Renesas R0E000010ACB10 User manual

User’s Manual
R0E000010ACB10 R20UT0164EJ0300
Rev.3.00
Oct 14, 2011
Isolator for the E1 Emulator
R20UT0164EJ0300 Rev.3.00 Page 1 of 8
Oct 14, 2011
1. Preface
The R0E000010ACB10 is an isolator for the E1 and E8a emulators. This product
is used for a debugging environment where there is a GND gap between the user
system and emulator system.
Package Components
Before using this product, check if your R0E000010ACB10 contains all of these
items.
Table 1.1 Package Components
Item Qty.
R0E000010ACB10 (Isolator for the E1 emulator) 1
R0E000010ACB10 User's Manual (English) (This manual) 1
R0E000010ACB10 User's Manual (Japanese) 1
Note: Please handle this product as precision equipment for transportation.
Important
When disposing of this product:
Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.
European Union regulatory notices
Renesas development tools and products are directly covered by the European Union's Waste Electrical and
Electronic Equipment, (WEEE), Directive 2002/96/EC. As a result, this equipment, including all accessories, must
not be disposed of as household waste but through your locally recognized recycling or disposal schemes. As part of
our commitment to environmental responsibility Renesas also offers to take back the equipment and has implemented
a Tools Product Recycling Program for customers in Europe. This allows you to return equipment to Renesas for
disposal through our approved Producer Compliance Scheme. To register for the program, click here
“http://www.renesas.com/weee".
Notes on Handling the Board:
Take full care not to touch any parts or cause short circuits on this product.
Protect this product from excessive physical shock.
Do not modify this product. Modifying the product will void your warranty.
Notes on Connecting the Board:
Always switch OFF the power before connecting or disconnecting this product.
This product has some switches. Make settings depending on debugging interface you use.
Before changing settings power off this product and other connected devices.
To connect this product to the user system align the #1 pin of the connector to the right position.
To connect this product to the emulator align the #1 pin of the connector to the right position.
European Union regulatory notices
This product complies with the following EU Directives.
Environmental Compliance and Certifications:
Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive
2002/95/EC
Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC

R0E000010ACB10 User’s Manual
R20UT0164EJ0300 Rev.3.00 Page 2 of 8
Oct 14, 2011
2. Specifications
Table 2.1 Product Specifications
Item Specification Remark
Supported Emulator 1) E1 emulator
2) E8a emulator This isolator is not usable with the E20 emulator.
Power supply Both of the following two power supplies are
necessary.
1) Supply from the user system (UVCC)
Voltage: 3.0 V to 5.5 V
2) Supply from the emulator’s power supply
facility
Voltage: 3.3 V
Supply from the user system (UVCC)
needs to be 50 mA (max).
Applicable MCU Series RX600 Series
RX200 Series
R32C/100 Series
M32C/80 Series
M16C/60 Series *1
M16C/50 Series *1
M16C/30 Series
M16C/Tiny Series
R8C/Lx Series
R8C/Mx Series
R8C/5x Series
R8C/3xT-A Series
R8C/3x Series
R8C/2x Series
R8C/1x Series
H8S/Tiny Series
H8/300H Tiny Series
H8/300H Super Low Power Series
H8/300L Super Low Power Series
38000 Series
Isolator's switch settings vary
depending on the target MCU you
use.
See 4.5 Switch Settings for Each
MCU for switch setting.
Device for isolation ACSL-6420-00TE (Avago Technologies US Inc.)
IL260-3E (NVE Corporation)
IL261-3E (NVE Corporation)
LED indication LED1: Illuminated when power is supplied from
the emulator
LED2: Illuminated when power is supplied from
the user system
This isolator is only usable when both
LEDs are illuminated.
*1 Clock-asynchronous serial (communication via CNVss pin) of the M16C/60 Series and the M16C/50 Series is not supported.
3. Notes on Usage
Note on power-supply voltage:
When you use an emulator with this isolator connected, power-supply voltage of the MCU on your system should be
between 3.0 V and 5.5 V. Power-supply voltage less than 3.0 V is not supported.
Note on signal delay:
When this isolator is connected, because of signal delay in the isolation circuit, speed of the communication interface
may be limited. As an example, the JTAG frequency of the RX600 series needs to be 12.38 MHz or less.
Note on Use temperature:
Please use this product at 5 - 35°C.
Note on power supply of disconnect:
Please turn off the emulator debugger and turn off the power supply of the user system when you disconnect.
If the power supply of the user system is not turned off, the reconnection cannot be likely to be done normally.
When an attempt to reconnect to the user system has failed, turn off the user system and then unplug and plug the USB
cable of the emulator before trying again.

R0E000010ACB10 User’s Manual
R20UT0164EJ0300 Rev.3.00 Page 3 of 8
Oct 14, 2011
4. Usage
The sections 4.2 and 4.3 in this chapter explain the usage of this product taking an example of the E1 emulator. Read
“E1” as “E8a” when using the E8a emulator.
4.1 Setting Switches (JP1-JP6)
To configure the circuit of this product depending on the communication method of the MCU you use, set switches JP1
through JP6. For details, see 4.5 Switch Settings for Each MCU.
4.2 Setup
Confirm both the user system and the emulator are switched OFF before installing this product. Do not connect the
USB cable to the emulator.
To connect this product to the user system or the emulator, be sure to align the #1 pin of the connector to the right
position.
Figure 4.1 Mounting the R0E000010ACB10
4.3 Starting the Power Supply
Start the power supply following the procedure below.
(1) Turn ON the emulator.
Connect the host machine and the E1 emulator with the USB cable, then switch ON the E1 emulator.
(2) Turn ON the user system.
Turn ON the user system.
(3) Start the debugger (Power supply setting).
Start the debugger from the control PC, and set the power supply to the target device to ON in the initial setting
screen. Select 3.3V for supply voltage regardless of the voltage used for the user system.
For the settings after the above, refer to the user’s manual for the emulator used (E1 or E8a).
U
ser s
y
stem
E1
emu
l
ato
r
Isolation board for the E1 (R0E000100ACB10)
E1
user
i
nter
f
ace
cable
C
onnector
f
or t
h
e
E1
(
14-
p
in connector
)

R0E000010ACB10 User’s Manual
R20UT0164EJ0300 Rev.3.00 Page 4 of 8
Oct 14, 2011
al Dimensions 4.4 Extern
S
o
ld
ere
d
s
id
e
P
arts s
id
e
U
n
i
t: mm
Figure
4.2 Ex sionsternal Dimen

R0E000010ACB10 User’s Manual
R20UT0164EJ0300 Rev.3.00 Page 5 of 8
Oct 14, 2011
ch MCU4.5 Switch Settings for Ea
Table 4.1 dence between the MCUs Supported by the E1 and t tch Settings
MCU User interface Switch setting No.
See Table 4.3
Correspon he Isolator Swi
JTAG Setting 1RX Family RX600 Series When using Flash Development Toolkit Setting 2
FINE Setting 7RX Family RX200 Series When using Flash Development Toolkit Setting 2
R8C Family R8C/Lx Series
R8C Family R8C/5x Series
R8C Family R8C/3xT-A Series
R8C Family R8C/3x Series
1-line clock-asynchronous serial
(communication via MODE pin) Setting 3
Table 4.2 Correspondence between the MCUs Supported by the E8a and the Isolator Switch Settings
MCU User interface
Switch setting
See T No. able 4.3
R8C Family R8C/Mx Series
R8C Family R8C/Lx Series
R8C Family R8C/3x Series
R8C Family R8C/2x Series
R8C Family R8C/1x Series
R8C/14,15,16,17,18,19,1A,1B Groups
1-line clock-asynchronous serial
(communication via MODE pin) Setting 3
Clock-synchronous serial
(communication via P00/P37/CNVss pin) Setting 4R8C Family R8C/1x Series R8C/10,11,12,13 Groups When using Flash Development Toolkit Setting 3
M16C Family R32C/100 Series
M16C Family M32C/80 Series
M16C Family M16C/60 Series
M16C/6S Group
Clock-synchronous serial Setting 6
Clock-asynchronous serial
(communication via CNVss pin) Not supportedM16C Family M16C/60 Series M16C/6C,6B, 64A,65,63 Groups Clock-synchronous serial
(communication via P64/P65/P66/P67) Setting 6
M16C Family M16C/60 Series
M16C/64,62P,6N Groups Clock-synchronous serial (communication via P64/P65/P66/P67) Setting 6
Clock-asynchronous serial
(communication via CNVSS pin) Not supportedM16C Family M16C/50 Series
Clock-synchronous serial
(communication via P64/P65/P66/P67) Setting 6
M16C Family M16C/30 Series
M16C Family M16C/Tiny Series Clock-synchronous serial (communication via P64/P65/P66/P67) Setting 6
Clock-synchronous serial Setting 4H8 Family H8/300L Super Low Power Series
H8 Family H8/300H Tiny Series
H8 Family H8/300H Super Low Power Series
H8S Family H8S/Tiny Series
When using Flash Development Toolkit Setting 2
740 Family 38000 Series
38D5,38D2,3803L,3804L Groups Clock-synchronous serial Setting 5

R0E000010ACB10 User’s Manual
R20UT0164EJ0300 Rev.3.00 Page 6 of 8
Oct 14, 2011
Switch setting No. Settings of JP1 to JP6
Table 4.3 Isolator Switch Setting
Setting 1
Setting 2
Setting 3
Setting 4
Setting 5
Setting 6
Setting 7
* other than thDo not use the isolator with settings e above.

R0E000010ACB10 User’s Manual
5. Warranty
R20UT0164EJ0300 Rev.3.00 Page 7 of 8
Oct 14, 2011
es with a one-year warra
(1) Should the product break down or be damage s user’s
manual, it will be repaired or replaced free
er, if the following failure or damage o aired
replaced at cost.
a) Failure or damage attributable to the misuse o ditions.
b) Failure or damage attributable to improper ha he
product when it is transported or moved.
ilure or damage to the product caused by
d) Failure or damage attributable to fire, earthqu normal
voltages, etc.
e) Failure or damage attributable to modificatio by other
an Renesas Electronics Corporation.
(3) This product is accessories product. We ca
ions
This product is only intended for use in a laborato
conditions. A safe separation distance should be u de the
laboratory, classroom, study area or similar such f
ctromagnetic Compatibility Directive and cou
The product generates, uses, and can radiate radio f radio
communications. However, there is no guarantee th is
ent causes harmful interference to radio
ent off or on, you are encouraged to try to
measures;
• ensure attached cables do not lie across th
• increase the distance between the equipment and the receiver
• connect the equipment into an outlet on a circuit different from that which the receiver is connected
• power down the equipment when not is use
• consult the dealer or an experienced radio/TV technician for help NOTE: It is recommended that wherever
possible shielded interface cables are used.
The product is potentially susceptible to certain EMC phenomena. To mitigate against them it is recommended
that the following measures be undertaken;
• The user is advised that mobile phones should not be used within 10m of the product when in use.
• The user is advised to take ESD precautions when handling the equipment.
This product does not represent an ideal reference design for an end product and does not fulfil the regulatory
standards for an end product.
This product com nty after purchase.
d while you’re using it under normal condition based on it
of cost.
ccurs to the product under warranty, the product will be rep(2) Howev
or r abuse of the product or its use under other abnormal con
ndling of the product after purchase, such as dropping of t
c) Fa other pieces of equipment connected to it.
akes, thunderbolts, floods, or other natural disasters or ab
ns, repairs, adjustments, or other acts made to the product
th
nnot accept any request for repair.
Precaut
ry environment under ambient temperature and humidity
sed between this and any sensitive equipment. Its use outsi
area invalidates conformity with the protection requirements o
the Ele ld lead to prosecution.
requency energy and may cause harmful interference to
at interference will not occur in a particular installation.
or television reception, which can be determined by turning the
If th
equipm
equipm correct the interference by one or more of the following
e equipment
• reorient the receiving antenna

http://www.renesas.com
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2880 Scott Boulevard Santa Clara,CA 95050-2554,U.S.A.
Tel: [phone],Fax:[phone]
Renesas Electronics Canada Limited
1101 Nicholson Road,Newmarket,Ontario L3Y 9C3,Canada
Tel:[phone],Fax:[phone]
Renesas Electronics Europe Limited
Dukes Meadow,Millboard Road,Bourne End,Buckinghamshire,SL8 5FH,U.K
Tel:[phone],Fax:[phone]
Renesas Electronics Europe GmbH
Arcadiastrasse 10,40472 Düsseldorf,Germany
Tel:[phone],Fax:[phone]
Renesas Electronics (China) Co.,Ltd.
7th Floor,Quantum Plaza,No.27 ZhiChunLu Haidian District,Beijing 100083,P.R.China
Tel:[phone],Fax:[phone]
Renesas Electronics (Shanghai) Co.,Ltd.
Unit 204,205,AZIA Center,No.1233 Lujiazui Ring Rd.,Pudong District,Shanghai 200120,China
Tel:[phone],Fax:[phone] / -7898
Renesas Electronics Hong Kong Limited
Unit 1601-1613,16/F.,Tower 2,Grand Century Place,193 Prince Edward Road West,Mongkok,Kowloon,Hong Kong
Tel:[phone],Fax:[phone]
Renesas Electronics Taiwan Co.,Ltd.
7F,No.363 Fu Shing North Road Taipei,Taiwan
Tel:[phone],Fax:[phone]
Renesas Electronics Singapore Pte.Ltd.
1 harbourFront Avenue,#06-10,keppel Bay Tower,Singapore 098632
Tel:[phone],Fax:[phone]
Renesas Electronics Malaysia Sdn.Bhd.
Unit 906,Block B,Menara Amcorp,Amcorp Trade Centre,No.18,Jln Persiaran Barat,46050 Petaling Jaya,Selangor Darul Ehsan,Malaysia
Tel:[phone],Fax:[phone]
Renesas Electronics Korea Co.,Ltd.
11F.,Samik Lavied' or Bldg.,720-2 Yeoksam-Dong,Kangnam-Ku,Seoul 135-080,Korea
Tel:[phone],Fax:[phone]
SALES OFFICES
Renesas Tools Website http://www.renesas.com/tools
A
ll trademarks and registered trademarks are the property
of their respective owners.
If the requirements shown in the "CAUTION"
sentences are ignored, the equipment may cause
personal injury or damage to the products.
© 2011 Renesas Electronics Corporation and Renesas Solutions Corp. All rights reserved.
Colophon 1.0
Notice
1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or
using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to
additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website.
2. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas
Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual
ics or others.
or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.
4. Descriptions rate the operation of semiconductor products and application examples. You are
fully responsi r equipment. Renesas Electronics assumes no responsibility for any losses incurred by
you or third p ising from the use of these circuits, software, or information.
5. When export ed by
such laws an y the
military, including b ectronics products and technology may not be used for or incorporated into any products
or systems w se m foreign laws or regulations.
6. Renesas Ele e.
Renesas Ele
7. Renesas Ele onic ording to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas
Electronics p ular
application. ou may not
use any Rene be in any way
liable for any hich the
product is no tend t of Renesas Electronics. The quality grade of each Renesas Electronics product is "Standard" unless
otherwise ex
"Standard": e tools;
"High Qualit utomobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment
"Specific": vices or
sy n (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life.
8. You should u nt within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating
supply voltag nesas Electronics shall have no liability for
malfunctions
9. Althoug Ren aracteristics such as the occurrence of failure at a
certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety
measu to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for
hardware but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures.
Because omputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you.
10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use
Renesas tation, the EU RoHS
Directive. R
11. This docume
12. Please conta ve any other
inquiries.
(Note 1) "Renesas -owned subsidiaries.
(Note 2) "Renesas ectronics product(s)" means any product developed or manufactured by or for Renesas Electronics.
property rights of Renesas Electron
3. You should not alter, modify, copy,
of circuits, software and other related information in this document are provided only to illust
ble for the incorporation of these circuits, software, and information in the design of you
arties ar
ing the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures requir
d regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use b
ut not limited to the development of weapons of mass destruction. Renesas El
anufacture, use, or sale is prohibited under any applicable domestic orho
ctronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error fre
ctronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.
ctr s products are classified acc
roduct depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a partic
You may not use any Renesas Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, y
sas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not
damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Specific" or for w
t in ed where you have failed to obtain the prior written consen
pressly specified in a Renesas Electronics data sheets or data books, etc.
Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machin
personal electronic equipment; and industrial robots.
y": Transportation equipment (a
not specifically designed for life support.
Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support de
stems), surgical implantations, or healthcare interventio
Renesas Electronics products described in this documese the
e range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Re
or damages arising out of the use of Renesas Electronics products beyond such specified ranges.
esas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific chh
res
and software including
the evaluation of microc
Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limi
enesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
nt may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics.
ct a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you ha
Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority
El