Repotec RP-1008W User manual

8 Port Nway Fast Ethernet
Web Smart Switch
User’s Manual

UFCC Warning
This device has been tested and found to comply with limits for a Class B digital device, pursuant to
Part 2 and 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates and radiates radio frequency energy and, if not installed and used in accordance with the
user’s manual, it may cause interference in which case users will be required to correct interference at
their own expenses.
UCE Warning
This is a Class B product. In a domestic environment, this product may cause radio interference in
which case the user may be required to take adequate measures.
UIntroduction
This switch provides 5/8 10/100M ports. It was designed for easy installation and high
performance in an environment where traffic is on the network and the number of
users increases continuously.
The small palm size with transparent plastic case was specifically designed for small
to medium workgroups. It can be installed where space is limited; moreover, it
provides smooth network migration and easy upgrade to network capacity.
UPackage Contents
Before you start to install this switch, please verify your package that contains the
following items:
zOne Fast Ethernet Switch
zOne Power Adapter
zOne User’s Manual
Note: If any of these items is found missing or damaged, please contact your local
supplier for replacement.
UKey Features
zSupports real time status(link,speed, duplex) of each port.
zSupports port setting for enable or disable operation (the 1’st port can’t be
disabled).
zSupports port setting for N-Way or force mode operation.
zSupports Broadcast Storm Protection.
zSupports Maximum Packet Length 1536 or 1552.
zSupports Port-bases VLAN.
zSupports two priority queues for QoS.
zSupports weighted round robin scheduling for queues.
zSupports Port-bases / 802.1p / Diff serv. priority three types of CoS.
1

UPowerU
Power is supplied through an external DC power adapter.
UFront Panel (LEDs)
LED Indicators of 5/8 Port 10/100M Switch
LED Status Operation
On Power is on.Power Off Power is off.
On Port is for connection
Off No connection.
LINK/ACT
Flashing Data is transmitting or receiving.
URear Panel (Connections)
Switch/Hub to this 5/8 Port Fast Ethernet Switch
This switch provides automatic crossover detection functionality for any port. It is
simple and friendly to up-link to another switch without crossover cable.
PC/Other devices to this 5/8 Port Fast Ethernet Switch
Via a twisted pair cable straight through, this switch can be connected to PCs, servers
and other network devices.
U
2

Configure
Please follow the steps to configure this Web Smart switch.
Step 1:
Use a twisted pair cable to connect this switch to your PC.
Step 2:
Set your PC’s IP to 192.168.2.xx.
Step 3:
Open the web browser (like IE…), and go to 192.168.2.1 site, and then you will see
the login screen.
Key in the user ID and the password to pass the authentication,
IP: 192.168.2.1
ID: admin
Password: admin
After the authentication procedure, the home page shows up.
3

Step 4:
On the following home page, select the configuration by clicking the icon. It
includes,
- Administrator
- Port Management
- VLAN Setting
- QoS Setting
- Port Security
- Logout
Administrator: Authentication Configuration
You can change the user name and the password, and click “Update” to confirm the
new change. After that, you can reset this switch by power off and then power on to
take the new user name and the password effectively.
4

Administrator: System IP Configuration
You can change the IP address by typing the new IP address and click “Update” to
confirm the new change, and then the message will show “Setting Process OK!!”,
After that, you should reset this switch by power off and then power on it to complete
the new change.
Administrator: System Status
It shows this switch MAC address, and you can select “Back to the last display” or
“Logout” when the time’s out.
Administrator: Load Default Setting to EEPROM
You can click “Load” to load the new factory default setting, and then reset the switch
by power off and then power on to take it effectively.
5

Administrator: Firmware Update
Follow the instruction on the screen to update the new firmware. Please contact with
your sales agents to get the latest firmware information.
Port Management: Port Control Configuration
Select the “Port No.” which you want to configure the mode below,
“Capability” - Auto-Nego. or force on 100M or 10M mode
“Duplex” - you can select the port is full/half-duplex or enable/disable this port.
6

Port Management: Bandwidth Control
Select the “Port No.” which you want to configure the mode below,
“TX Rate” is meant you can set the maximum transmission rate of this selected port
and choose the full speed or in 128K/256K/512K/1M/2M/4M/8M speed.
“RX Rate” is meant you can set the maximum receiving rate of this selected port and
choose full speed or in 128K/256K/512K/1M/2M/4M/8M speed.
Port Management: Broadcast Storm Control
You can enable or disable the broadcast storm protection feature by clicking “Update”.
7

Port Management: Max Packet Length
You can select the maximum packet length setting, 1536 byte or 1552 byte of this
switch.
VLAN Setting: Group VLAN Setting
There are 4 VLAN groups, 01, 02, 03, 04, can be used.
You can select a group, and then click the port number which you want to put it into
the selected VLAN group.
8

VLAN Setting: Multi to 1 Setting
This is a special design for easily setting the switch VLAN into “VLAN Per Port“.
After this setting, all ports can only connect to the destination port.
QoS Setting: Class of Service Configuration
You can select the class of service for each port.
QoS Setting: High Priority Queue Configuration
You can select WRR low weight 1/4 or 1/8.
9

QoS Setting: Customization Diffserv
Please follow the instruction on the screen to update the setting.
Port Security
When this function is enabled, the port will record the first receiving source MAC
address as the security MAC address and only allow the packet which has this MAC
address to activate on the port.
Logout: You can click “Logout” to logout.
U
10

Technical Specifications
Standards zIEEE 802.3 10BaseT
zIEEE 802.3u 100Base TX
zIEEE 802.3x Flow Control
zIEEE 802.1Q VLAN Tagging
zIEEE 802.1p, Class of Service, Priority Protocols
Ports z8 * RJ45 ports, with 10/100Mbps
Transmission method zStore-and-forward
Packet Buffer z512K bits
Mac Table Size z1K
Smart Features zPort-based VLAN: Maximum 5/8
zQoS: 2 Queues
zManagement: Password-protectedAccess, Port Settings,
Web-base Management, Graphic User Interface
Filtering/Forwarding Rates z100Mbps port – 148,800pps
z10Mbps port – 14,880pps
Transmission Media z10BaseT Cat. 3,4,5 UTP/STP
z100BaseTX Cat. 5 UTP/STP
Led Indicators zPer Port: Link/Act
zPer Unit: Power
Power zDC7.5V 0.8A adapter
Dimension z140* 105* 25 mm
Environment zOperating temperature : 0 to 40℃
zHumidity:10% to 90% (Non-condensing)
Certification zCE, FCC
11