Repotec RP-G3224DB User manual

24-Port 10/100M +
2-Port Gigabit
Fast Ethernet Switch
User´s Manual
V1.0
1 | Page

FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including interference that
may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 class A for ITE, the essential protection requirement of
Council Directive 2004/108/EC on the approximation of the laws of the Member
States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible
that information in this document is not up-to-date. Please check with your local
distributors for the latest information. No part of this document can be copied or
reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
2 | Page

The Ethernet Switch is suitable for the networking of small and medium-sized
enterprises, Internet cafe and households. The Ethernet Switch provides 24 *
10/100M, 2 * 10/100/1000M, and 2 SFP Ports.
HARDWARE INSTALLATION
Location
Choose a suitable location for the rack mountable switch, considering the following
requirements:
Suitable power source
Keep it away from heat sources and sunlight
Keep it away from electromagnetic interference
Allow 10 cm space above the unit for good ventilation
Installation
1. Remove the backing paper from the rubber feet and stick one in each of the
indicated locations on the bottom of the switch.
2. Attach the L” bracket to the front corners of the switch using the mounting
screws.
3. Place the switch in a standard EIA 19" rack. Adjust the mounting brackets so
the holes align with the mounting holes in the rack and fasten the switch to the
rack (NOTE: screws are not provided with the switch for this purpose).
4. Plug the power cable into the socket at the rear of the switch and an
appropriate power source. The switch will adjust the input voltage
automatically within the input range indicated on the rear panel.
5. The switch performs a self-test (all LED indicators on the status panel flash
then sweep from left to right).
When the lights turn off, the test is finished and the switch is ready for use.
6. To connect data sources, plug one end of an Ethernet cable into one of the
numbered RJ45 ports of the switch and connect the other end to the source.
Category 3, 4 or 5 cables can be used, however Category 5 is recommended.
Caution: Do not connect a phone line to the RJ-45 port; phone signals will
damage the unit.
3 | Page

LED Indicators
When the power to the switch is on, the following indicators show system status:
Technical Specifications
Items
Specification
Standards and
Protocols
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z,
IEEE 802.3x
Fixed Port
24 10/100M auto-negotiation RJ45 port
2 gigabit uplink RJ45/SFP(mini GBIC) multiplex port
Cable Type
10Base-T: Category 3/4/5 UTP, support maximum
transmission distance 100m
100Base-
TX: CAT5 UTP, support maximum transmission
distance 100m
1000Base-T: CAT5e UTP, support maximum
transmission distance 100m
Fiber Type
50/125µm multimode fiber, transmission distance 550m
9/125µm single mode fiber, transmission distance 10km
9/125µm single mode fiber, transmission distance 40km
9/125µm single mode fiber, transmission distance 80km
LED Indicators
Power, Link/Act 1~26, Speed 1~26
Background Bandwidth
8.8Gbps
MAC Address Table
8K
Forwarding Rate
10Mbps: 14880PPS
100Mbps: 148800PPS
100Mbps: 1488000PPS
Dimensions (W*H*D)
440*180*44(mm)
Input Voltage
100V~240VAC,50/60Hz
Power Consumption
< 15W
Working Temperature
0ºC
～
40ºC
Store Temperature
-40ºC
～
70ºC
Operating Humidity
10%
～
90% RH Non-Condensing
4 | Page

Storage Humidity
5%
～
90% RH Non-Condensing
Heat Dissipation
natural heat dissipation
Package contents:
Fast Ethernet switch*1
AC power cord*1
Rubber foot*4 and screws
Rack-mounted bracket *2
User manual*1
5 | Page