Repotec RP-PE054 User manual

5 ports Fast Ethernet Switch
With 4 Ports 802.3at PoE
User Manual
Ver 1.0

1
Introductions
The PoE Switch is a 5-port 10M/100M Fast Ethernet Switch with one uplink port plus
4 ports of Power over Ethernet capability. Per PoE port is power supply up to 30W.
The total PoE power budget is 65W. It is an ideal solution where office and home
users utilize a combination of PoE and non-PoE enabled devices.
PoE Functionality for the LAN
Four ports on the PoE Switch are PoE enabled making it an ideal solution for most
office users that have PoE enabled devices located around the office. These
products can include a mixture of PoE IP Phones, PoE wifi APs and PoE IP Cam. It
is the perfect answer for offices that are upgrading their office equipment and LAN
infrastructure to include PoE capability. The switch automatically detects IEEE
802.3at/af compliant device connected and provides power and data over a single
cable to these devices.
Stable and Reliable Network Environment
The PoE Switch enables users to deploy a stable and reliable high-speed LAN
environment, with store-and-forward switching architecture, packet error filtering and
non-blocking packet forwarding. The 802.3x and backpressure flow control
mechanisms work respectively for full and half duplex modes. This device supports
N-way auto-negotiation protocol that automatically detects networking speed and
duplex modes.
Easy to Use
For instant error detection, the switch is equipped with a full range of LEDs to help
monitor and troubleshoot problems on the network.
Packing List
Inside the package you should find:
(1) One PoE Switch
(2) One Power Cord
(3) One User Manual
Please check if the packing is damaged or any component is missing. If so, please
contact your distributor.

2
Installation Steps
1. Use the power cord to power up the PoE switch, and the LED indicator “Power”
will be on.
2. Connect “UPLINK” port of the PoE switch to other LAN switch via Ethernet
Cat.5e/6/7 cables. The LED indicator “UPLINK” will be on.
3. Connect “LAN” ports of the PoE Switch to PoE PD devices. The corresponding
LED indicators “LAN” and “PoE” will be on.
4. Check whether the PoE PD device is on. If not, please make sure all Ethernet
cables are connected correctly and fastened tightly.
LED Indicators
On the front panel of PoE Switch, there are 10 LED indicators as the following;
POWER: “Green On” indicates power is on and normal.
UPLINK: “Green On” indicates Ethernet is in connection at 10/100M.
“Green Flashing” indicates Ethernet in data activities.
LINK: “Green On” indicates Ethernet is in connection at 10/100M.
“Green Flashing” indicates Ethernet in data activities.
PoE: “Green On” indicates Power over Ethernet function is enabled.
“OFF” indicates the PoE is disabled, and it becomes a regular LAN port.

3
Technical Specifications
Standards
IEEE 802.3: 10 BASE-T
IEEE 802.3u: 100 BASE-TX
IEEE 802.3at/af: Power Over Ethernet
Features
MAC Address: 1K
Buffer Memory: 512K bits
Transmission Method: Store and Forward
Filtering/Forwarding
Rates
100Mbps port - 148,800pps
10Mbps port - 14,880pps
Transmission Media
10BaseT Cat. 3, 4, 5 UTP/STP
100BaseTX Cat. 5 UTP/STP
Interface
5 x 10/100Mbps RJ-45 ports
Uplink Port
1
PoE Spec
Supports up to 30W per PoE port
PoE power budget: 65W
PD classification identify
PoE over current protection
PoE circuit sorting protection
PoE power on RJ-45 pin 1,2 for power ”+” / pin 3,6
for
power “-“
LED Indicators
Power, Uplink , LAN1~4 port , PoE 1~4 port
Power Supply Internal Power 100~240VAC/50~60Hz
Dimensions
160 × 122 × 44 mm
Weight
0.8 kgs
Operating Temperature 0 to 40℃
Humidity
10 to 90% RH (non-condensing)
Certifications
FCC , CE
P/N: 41NE-PE054000-A00