ResMed HumidAire 3i User manual

HumidAire 3i™
User’s Manual
English • Deutsch • Français • Italiano
Español • Português • Nederlands
338284r3 Cover.qxp 27/11/2006 10:07 AM Page 1

HumidAire 3i™
A
B
12
4
D
1 4
1
2
56
234
3
© 2006 ResMed Ltd. © 2006 ResMed Ltd. © 2006 ResMed Ltd. © 2006 ResMed Ltd. © 2006 ResMed Ltd.
C
E
12
3
(a)
(a)
Component of 338284/3
Air outlet / Luftauslass /
Sortie d'air /
Presa di uscita dell'aria /
Salida de aire / Saída de ar /
Luchtuitgang
Control dial / Regler / Bouton de
réglage / Selettore di regolazione /
Escala de control /
Botão de controle / Schaal
Docking station / Andock-Station
Support / Unità di alloggiamento
Estación de carga / Estação de
ancoragem / Docking-station
Heater plate
Heizplatte / Plaque chauffante /
Piastra di riscaldamento / Placa de
calefacción / Placa de aquecimento /
Verwarmingsplaat
Latch / Lasche /
Languette / Gancio
d'arresto / Cerrojo /
Trinco / Vergrendeling
Cover / Deckel / Capot / Coperchio /
Cubierta / Tampa / Afdekplaat
Cover seal / Deckeldichtung / Joint du capot /
Guarnizione del coperchio / Junta de la cubierta /
Vedação da tampa / Afdekplaatafdichting
Connector seal / Konnektordichtung /
Joint du connecteur / Guarnizione del connettore /
Junta conectora / Vedação do conector /
Connectorafdichting
Water chamber /
Befeuchterkammer /
Réservoir /
Camera dell'acqua /
Cámara de agua /
Câmara de água /
Waterkamer
ILLUSTRATIONS
ABBILDUNGEN
ILLUSTRATIONS
ILLUSTRAZIONI
FIGURAS
ILUSTRAÇÕES
ILLUSTRATIES
REMOVING THE FRONT CAP (IF FITTED) / ABNEHMEN DER FRONTABDECKUNG
(FALLS VORHANDEN) / RETRAIT DU CAPOT AVANT (LE CAS ÉCHÉANT) / RIMOZIONE DEL
COPERCHIO FRONTALE (SE INSTALLATO) / PARA QUITAR LA CUBIERTA DELANTERA (SI ESTÁ
INSTALADA) / REMOÇÃO DA TAMPA DA FRENTE (NO CASO DESTA SE ENCONTRAR EM POSIÇÃO) /
VERWIJDEREN FRONTKAP (INDIEN AANWEZIG)
REMOVING AND STORING THE CONNECTOR PLUG / ENTFERNEN UND
AUFBEWAHRUNG DES KONNEKTORSTECKERS / RETRAIT ET RANGEMENT DU CACHE DU
CONNECTEUR / RIMOZIONE E SISTEMAZIONE DELLA SPINA DEL CONNETTORE / PARA
QUITAR Y GUARDAR EL ENCHUFE CONECTOR / REMOÇÃO E ARMAZENAGEM DA TAMPA
DO CONECTOR / VERWIJDEREN EN OPSLAG CONNECTORPLUG
Connector plug / Konnektorstecker / Cache du connecteur / Spina del
connettore / Enchufe conector / Tampa do conector / Connectorplug
ATTACHING YOUR HUMIDAIRE 3i / ANSCHLUSS IHRES HUMIDAIRE 3i / FIXATION DE VOTRE HUMIDAIRE 3i / COLLEGAMENTO DELLO HUMIDAIRE 3i / ACOPLE DEL HUMIDAIRE 3i /
MONTAGEM DO HUMIDAIRE 3i / BEVESTIGING VAN UW HUMIDAIRE 3i
FILLING THE WATER CHAMBER / AUFFÜLLEN DER BEFEUCHTERKAMMER / REMPLISSAGE DU RÉSERVOIR / RIEMPIMENTO DELLA CAMERA DELL'ACQUA /
LLENADO DE LA CÁMARA DE AGUA / ENCHER A CÂMARA DE ÁGUA / VULLEN VAN DE WATERKAMER
Front cap /
Frontabdeckung /
Capot avant /
Forhette /
Coperchio frontale /
Cubierta delantera /
Tampa da frente /
Frontkap
338284r3 illos.qxp 14/11/2006 12:46 PM Page 1

I
1 2
34
5
© 2006 ResMed Ltd.
6
F H
3
56
9
1
4
10 min
G
© 2006 ResMed Ltd.© 2006 ResMed Ltd.
© 2006 ResMed Ltd.
2
3
54 UNDERSIDE VIEW / ANSICHT UNTERSEITE / VUE DU DESSOUS /
VISTA DAL DISOTTO / VISTA INFERIOR / VISTA INFERIOR /
AANZICHT ONDERZIJDE
78
1
10 min
2
STARTING YOUR TREATMENT / BEHANDLUNGSBEGINN / DÉBUT DE VOTRE TRAITEMENT / AVVIO DEL TRATTAMENTO /
INICIO DEL TRATAMIENTO / INICIAR O TRATAMENTO / BEGINNEN MET UW BEHANDELING
Left key / Linke Taste / Touche de gauche /
Tasto sinistro / Tecla Izquierda /
Tecla Esquerda / Linkertoets
Control panel / Bedienfeld /
Panneau de contrôle / Pannello di controllo / Panel de
control / Painel de controle / Bedieningspaneel
Control dial / Regler/ Bouton de réglage /
Selettore di regolazione / Escala de control /
Botão de controle / Schaal
Indicator light / Thermostatanzeige / Témoin lumineux /
Spia di funzionamento / Luz indicadora /
Indicador luminoso / Indicatielampje
Right key / Rechte Taste /
Touche de droite / Tasto destro /
Tecla Derecha / Tecla Direita /
Rechtertoets
Up/Down keys /
Pfeil-nach-oben-/Pfeil-nach-unten-Tasten /
Touches de déplacement vers le haut et vers le bas /
Tasto su/giù / Teclas Superior/Inferior / Teclas Para cima/Para baixo /
Omhoog/Omlaag-toetsen
Start/Stop key /
Start-/Stopptaste /
Touche Marche/Arrêt /
Tasto di avvio/stop /
Tecla de Inicio/Detención /
Tecla de Iniciar/Parar /
Start/Stop-toets
DETACHING YOUR HUMIDAIRE 3i / ABNEHMEN IHRES HUMIDAIRE 3i / RETRAIT DE VOTRE HUMIDAIRE 3i /
DISTACCO DELLO HUMIDAIRE 3i / DESACOPLAMIENTO DEL HUMIDAIRE 3i / SEPARANDO O SEU HUMIDAIRE 3i /
LOSKOPPELEN VAN UW HUMIDAIRE 3i
DETACHING YOUR HUMIDAIRE 3i / ABNEHMEN IHRES HUMIDAIRE 3i / RETRAIT DE VOTRE HUMIDAIRE 3i /
DISTACCO DELLO HUMIDAIRE 3i / DESACOPLAMIENTO DEL HUMIDAIRE 3i / SEPARANDO O SEU HUMIDAIRE 3i /
LOSKOPPELEN VAN UW HUMIDAIRE 3i
RE-ASSEMBLING YOUR HUMIDAIRE 3i / WIEDERZUSAMMENBAU IHRES HUMIDAIRE 3i /
REMONTAGE DE VOTRE HUMIDAIRE 3i / RIASSEMBLAGGIO DELLO HUMIDAIRE 3i /
MONTAJE DEL HUMIDAIRE 3i / REMONTAGEM DO HUMIDAIRE 3i /
HERMONTAGE VAN UW HUMIDAIRE 3i
Large silver button /
Große, silberne Taste /
Gros bouton argenté /
Grande bottone argentato /
Botón plateado grande /
Botão prateado grande /
Grote zilverkleurige knop
Press button and pull apart / Lasche drücken und auseinanderziehen / Appuyez
sur le bouton et tirez pour détacher / Premere il bottone e separare / Oprima el
botón y separe / Premir botão e separar / Knop indrukken, daarna lostrekken
338284r3 illos.qxp 14/11/2006 12:46 PM Page 2

USER’SMANUAL 1
MANUEL UTILISATEUR 43
BEDIENUNGSANLEITUNG 21
MANUALE DELL’UTENTE 65
HUMIDAIRE 3i™
ENGLISHDEUTSCHITALIANO FRANÇAISESPAÑOLPORTUGUÊS
NEDERLANDS
MANUAL DEL USUARIO 87
MANUAL DO UTILIZADOR 109
HANDLEIDING VOOR DE GEBRUIKER 131
338284r3.book Page iii Tuesday, November 14, 2006 1:23 PM

Patents and designs pending.
HumidAire, HumidAire 3i, S8 and SmartStart are trademarks of ResMed Ltd and HumidAire is registered in
U.S. Patent and Trademark Office.
© 2006 ResMed Ltd.
ResMed Ltd (Manufacturer) 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia
ResMed Corp (US Designated Agent) 14040 Danielson Street Poway CA 92064-6857 USA
ResMed (UK) Ltd (EU Authorized Representative) 65 Milton Park Abingdon Oxfordshire OX14 4RX UK
ResMed Offices Australia, Austria, Finland, France, Germany, Hong Kong, Japan, Malaysia, Netherlands,
New Zealand, Singapore, Spain, Sweden, Switzerland, UK, USA (see www.resmed.com for contact details).
338284r3.book Page iv Tuesday, November 14, 2006 1:23 PM

ENGLISH
1
USER’S MANUAL
English
HumidAire 3i™
338284r3.book Page 1 Tuesday, November 14, 2006 1:23 PM

2
CONTENTS
WELCOME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
WHAT IS THE HUMIDAIRE 3i? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
YOUR RESPONSIBILITY 3
MEDICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INTENDED USE 4
CONTRAINDICATIONS 4
WARNINGS 4
COMPONENTS OF YOUR HUMIDAIRE 3i . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SETTING UPYOUR HUMIDAIRE 3i FOR USE . . . . . . . . . . . . . . . . . . . . . . . 5
REMOVING THE FRONT CAP (IF FITTED) 5
REMOVING AND STORING THE CONNECTOR PLUG 6
ATTACHING YOUR HUMIDAIRE 3i 6
FILLING THE WATER CHAMBER 6
STARTING AND STOPPING TREATMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
STARTING YOUR TREATMENT 7
STOPPING YOUR TREATMENT 8
DETACHING YOUR HUMIDAIRE 3i 8
FREQUENTLY ASKED QUESTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DISASSEMBLING YOUR HUMIDAIRE 3i 10
CLEANING YOUR HUMIDAIRE 3i 10
REASSEMBLING YOUR HUMIDAIRE 3i 12
SERVICING 12
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
338284r3.book Page 2 Tuesday, November 14, 2006 1:23 PM

3
WELCOME
ENGLISH
WELCOME
Thank you for choosing the ResMed HUMIDAIRE 3i™ humidifier. The HUMIDAIRE 3i
is designed to humidify (moisten) the air delivered to your airway during CPAP
(continuous positive airway pressure) therapy. The HUMIDAIRE 3i attaches to your
ResMed S8™ Series CPAP flow generator with a simple ‘click-in’ mechanism.
This user manual contains the information you need for the correct use of your
HUMIDAIRE 3i.
WHAT IS THE HUMIDAIRE 3i?
The HUMIDAIRE 3i is designed to form a single unit with a ResMed CPAP flow
generator. The combined unit provides humidification during CPAP therapy, and can
make therapy more comfortable.
You may have experienced nasal congestion or dryness of the nose, mouth, or throat
during CPAP therapy. These symptoms are caused by dry climates, cold air
temperatures, the airflow delivered from your flow generator, or mouth leak. Moist air
may help relieve these symptoms of dryness.
Refer to your flow generator manual to see whether it is compatible with the
HUMIDAIRE 3i. Contact your equipment supplier or ResMed office if you require
further information.
YOUR RESPONSIBILITY
You or the user of this system shall have sole responsibility and liability for any injury
to persons or damage to property resulting from:
•operation which is not in accordance with the operating instructions supplied
•maintenance or modifications carried out unless in accordance with authorised
instructions and by authorised persons.
Please read this manual carefully before use.
This manual contains special terms and icons that appear in the margins to draw your
attention to specific and important information.
•Warning alerts you to possible injury.
•Caution explains special measures for the safe and effective use of the device.
•Note is an informative or helpful note.
338284r3.book Page 3 Tuesday, November 14, 2006 1:23 PM

4
MEDICAL INFORMATION
INTENDED USE
The HUMIDAIRE 3i is indicated for humidification of the air delivered from the ResMed
S8 Series CPAP devices. The HUMIDAIRE 3i is for use only as recommended by a
physician.
CONTRAINDICATIONS
The HUMIDAIRE 3i is contraindicated for use with patients whose upper (supraglottic)
airway has been bypassed. Please also refer to the relevant system manual for
contraindications associated with CPAP therapy.
WARNINGS
The following are general warnings. Specific warnings and cautions appear next to the
relevant instructions in the manual.
!
WARNINGS
•Use the HUMIDAIRE 3i only for its intended use as described in this manual.
•Make sure that the water chamber is empty before transporting the
HUMIDAIRE 3i.
•The HUMIDAIRE 3i is designed only for use with specific ResMed CPAP devices.
Do not use the HUMIDAIRE 3i with any other CPAP device.
•The HUMIDAIRE 3i should only be used with delivery tubes or accessories
recommended by ResMed. Connection of other delivery tubes or accessories
could result in injury, or damage to the device.
•The HUMIDAIRE 3i, including the associated tubing, is for single-patient use and
must not be re-used on another person. This is to avoid the risk of cross-infection.
•Always place the HUMIDAIRE 3i device lower than the level of the patient. If it is
placed at or above the level of the patient, heated water may flow down the air
tubing and into the mask.
•There exists the possibility that if the device is placed above the level of the patient
and is tipped over, or if the tubing is filled with condensate, the mask might fill with
water. The HUMIDAIRE 3i should therefore be used with caution in patients who
are unable to guard their airways, or are unable to pull the mask off, for example
following a stroke. Attention should be given to the relative risks and benefits.
•Do not attempt to dismantle the HUMIDAIRE 3i docking station. There are no
user-serviceable parts inside. Repairs and internal servicing should only be
performed by an authorised service agent.
•Take care when handling the HUMIDAIRE 3i. The heater plate and the water in the
water chamber may be hot.
•If liquids are inadvertently spilled into or on the HUMIDAIRE 3i docking station,
unplug the CPAP device from the power outlet. Disconnect the docking station
from the CPAP device and allow the docking station to drain and dry before using.
338284r3.book Page 4 Tuesday, November 14, 2006 1:23 PM

5
COMPONENTS OF YOUR HUMIDAIRE 3i
ENGLISH
•Do not operate the HUMIDAIRE 3i if the CPAP device has a damaged power cord
or plug.
•Do not operate the HUMIDAIRE 3i if it is not working properly or if any part of it
has been dropped or damaged.
•Keep the CPAP device power cord away from heated surfaces.
•Do not drop or insert any object into any opening or tubes.
•Do not use the HUMIDAIRE 3i in the presence of flammable or explosive
materials.
•Explosion hazard—do not use in the vicinity of flammable anaesthetics.
•If oxygen is used with this device, the oxygen flow must be turned off when the
device is not operating.
If oxygen has been left on, turn off the flow generator, then wait 30 minutes before
turning on the flow generator again.
Explanation: When the CPAP device is not in operation and the oxygen flow is
left on, oxygen delivered into the air delivery tubing may accumulate within the
CPAP machine enclosure and create a risk of fire. This applies to most types of
CPAP machines.
•Oxygen supports combustion. Oxygen should not be used while you are
smoking or in the presence of an open flame.
•Always ensure airflow is being generated by the device before the oxygen
supply is turned on.
•Always turn the oxygen supply off before stopping the airflow from the device.
Note: At a fixed rate of supplemental oxygen flow, the inhaled oxygen concentration
will vary, depending on where the oxygen is introduced, the pressure settings, patient
breathing pattern, mask selection and leak rate.
COMPONENTS OF YOUR HUMIDAIRE 3i
Please refer to the illustrations in section Aof the illustration sheet.
SETTING UPYOUR HUMIDAIRE 3i FOR USE
!
WARNING
Make sure your flow generator is switched off at the power outlet before
connecting the HumidAire 3i.
REMOVING THE FRONT CAP (IF FITTED)
Please refer to the illustrations in section Bof the illustration sheet.
Your flow generator may be fitted with a front cap (B-1). Before you can attach the
HUMIDAIRE 3i, press the button underneath the front cap (B-2) and pull it away from
the body of your flow generator (B-3 & B-4).
338284r3.book Page 5 Tuesday, November 14, 2006 1:23 PM

6
Notes
•To replace the front cap, align it with your flow generator (B-4) and push it firmly until it
clicks into place.
•Remember to take the front cap with you when travelling, in case you need CPAP
therapy without a humidifier.
REMOVING AND STORING THE CONNECTOR PLUG
Please refer to the illustrations in section Cof the illustration sheet.
Before attaching the HUMIDAIRE 3i, remove the connector plug from your flow
generator (C-1) and attach it to the back of the docking station (C-2).
ATTACHING YOUR HUMIDAIRE 3i
Please refer to the illustrations in section Dof the illustration sheet.
1Align your HUMIDAIRE 3i with your flow generator (D-1) and push them together
until they click into place (D-2).
!
WARNING
•The HumidAire 3i docking station should only be connected or disconnected
when the water chamber is empty.
•Water must be prevented from entering your flow generator. Do not transport
the flow generator with the HumidAire 3i attached.
2Insert the power cord into the socket at the rear of your flow generator. Plug the other
end of the power cord into a power outlet (D-3).
Note: If your flow generator is powered via the DC input, the HumidAire 3i is not powered
and humidification output will be reduced.
3Place the combined unit on a firm, level surface near your bed at a level lower than
your sleeping position. Ensure the surface is not sensitive to heat and/or moisture, or
use a protective mat.
!
CAUTION
Be careful not to place the unit where it can be bumped into and knocked over.
4Connect one end of the air tubing firmly onto the air outlet of your HUMIDAIRE 3i
and the other end to your mask (D-4).
FILLING THE WATER CHAMBER
Please refer to the illustrations in section Eof the illustration sheet.
!
WARNING
Take care when handling your HumidAire 3i. The water and the water chamber
base may both be hot. Allow ten minutes for the heater plate and any excess water
to cool.
1Release the cover latch (E-1) and lift the cover until it rests in the upright position (E-2).
338284r3.book Page 6 Tuesday, November 14, 2006 1:23 PM

7
STARTING AND STOPPING TREATMENT
ENGLISH
2Remove the water chamber (E-3) and carefully fill it with fresh, clean water (E-4). Make
sure you keep the level of the water under the maximum water level mark (E-4a).
Always ensure that the water chamber is clean. See “Cleaning and Maintenance” on
page 10.
!
WARNING
Do not overfill the water chamber, as water may enter your flow generator and air
tubing.
!
CAUTION
Do not use any additives (eg scented oils and perfumes). They may reduce the
humidification output of the HumidAire 3i and/or cause deterioration of the water
chamber materials.
3Carefully place the filled water chamber into the humidifier docking station (E-5) and
latch the cover (E-6).
The HUMIDAIRE 3i is now ready for use.
STARTING AND STOPPING TREATMENT
STARTING YOUR TREATMENT
Please refer to the illustration in section Fof the illustration sheet.
1When your HUMIDAIRE 3i is attached and the flow generator is powered, the
indicator light lights up on the HUMIDAIRE 3i. A prompt for the Warm-Up feature
(not available on all models) may appear.
When activated, this feature allows the water to warm up before you start treatment.
2If the Warm-Up feature is available, use it to pre-heat the water before starting your
treatment. Skip this step if you wish to start treatment immediately.
WARM-UPFEATURE (NOT AVAILABLE IN ALL MODELS)
Note: Check your flow generator user’s manual to see if this feature is available.
To start the Warm-Up feature:
i. Select Warmup by pressing the Right key on the control panel.
The following message is displayed for 2 seconds:
ii. After 2 seconds the WARMING screen is displayed.
RAMP: 10min
menu

warmup
HUMIDIFIER
WARMING
WARMING
menu exit
338284r3.book Page 7 Tuesday, November 14, 2006 1:23 PM

8
iii. While your HUMIDAIRE 3i is in Warm-Up mode you can:
•Start treatment at any time by pressing the Start/Stop key.
•Access the menus by pressing Menu (Left key).
•Stop the Warm-Up feature at any time by pressing Exit (Right key).
The Warm-Up feature will automatically turn off after 30 minutes if treatment has not
started.
3Turn the humidity control dial to the desired setting. The setting switches heated
humidification off and delivers minimum humidification. The indicator light will remain
lit to indicate standby mode. A setting of 6 ( ) delivers maximum humidification.
We recommend that you initially set the control dial to 3 ( ). If necessary, adjust the
control dial up or down to find the setting that is most comfortable and effective for
you. You can adjust the humidity setting at any time.
The aim is to have moist air delivered to your mask but to avoid condensation forming
in the air tubing. The temperature and humidity of the surrounding air will affect the
setting you need.
See “Frequently Asked Questions” for further tips on the correct humidity setting.
4Fit your mask as described in your mask user instructions.
5Press the Start/Stop key on the control panel. Alternatively, if your flow generator
has the SmartStart™ function available, simply breathe into your mask and air should
begin to flow.
Note: During operation, the indicator light becomes brighter to indicate that the heating
element is active. Your HumidAire 3i has a rapid heating element which allows very short
heating times. Do not be concerned if the light only brightens very briefly.
6Lie down and arrange the air tubing so that it is free to move if you turn in your sleep.
!
WARNING
Do not leave an excessive length of air tubing around the top of your bed. It could
twist around your head or neck while you are sleeping.
STOPPING YOUR TREATMENT
To stop your treatment at any time, remove your mask and press the Start/Stop key.
Alternatively, if your flow generator has the SmartStart function available, simply
remove your mask and treatment will end.
Some flow generators continue to blow air gently after you have stopped your
treatment. This can continue for up to one hour to assist the heater plate in cooling.
However, you can unplug the device from the power outlet at any time and allow the
heater plate to cool without airflow.
DETACHING YOUR HUMIDAIRE 3i
Please refer to the illustrations in section Gof the illustration sheet.
338284r3.book Page 8 Tuesday, November 14, 2006 1:23 PM

9
FREQUENTLY ASKED QUESTIONS
ENGLISH
1Unplug the power cord from the power outlet (G-1).
!
WARNING
Take care when handling your HumidAire 3i. The water and the water chamber
base may both be hot. Allow ten minutes for the heater plate and any excess water
to cool (G-2).
2Remove the water chamber from the docking station (G-3).
3Press the large silver button located midway underneath the docking station
(G-4) and pull the HUMIDAIRE 3i and flow generator apart (G-5).
Note: Re-attach the connector plug firmly to your flow generator.
FREQUENTLY ASKED QUESTIONS
WHY IS THERE CONDENSATION IN MY MASK AND/OR AIR TUBING?
You may experience excessive condensation in your mask or air tubing. This may occur
seasonally, particularly when the room temperature is low or cool air is circulating
around the tube. Turn the control dial down to a lower setting until the condensation
decreases.
You may have to adjust your humidity setting from season to season.
DOI HAVE TO USE DISTILLED WATER IN THE WATER CHAMBER?
Using distilled water will maximise the life of the water chamber and reduce mineral
deposits. See “Cleaning your HumidAire 3i” on page 10 for further details.
WHAT IF I STILL HAVE SYMPTOMS OF DRYNESS?
If you still experience symptoms of dryness, then your humidity setting may be set too
low to be effective. Gradually turn the humidity control dial up over a few nights until
the symptoms disappear.
If you are still experiencing symptoms of dryness, even after increasing the humidity
setting, you may be breathing through your mouth. Mouth breathing or mouth leaks
cause drying and irritation of the upper airway. If this is a problem, a full face mask or
chin strap may help. Consult your clinician or equipment supplier for details.
Large silver button
UNDERSIDE VIEW
338284r3.book Page 9 Tuesday, November 14, 2006 1:23 PM

10
CLEANING AND MAINTENANCE
You should regularly carry out the cleaning and maintenance of the water chamber,
cover and cover seal as described in this section.
DISASSEMBLING YOUR HUMIDAIRE 3i
Please refer to the illustrations in section Hof the illustration sheet.
!
WARNING
Beware of electrocution. Do not immerse your flow generator, docking station or
power cord in water. Always unplug the device before cleaning and be sure that it
is dry before plugging it back in.
1Unplug the power cord from the power outlet (H-1).
!
WARNING
Take care when handling your HumidAire 3i. The water and the water chamber
base may both be hot. Allow ten minutes for the heater plate and any excess water
to cool (H-2).
2Remove the water chamber from the docking station (H-3) and discard any excess
water (H-4).
3Detach the air tubing from the air outlet (H-5).
4Gently flex one cover arm away and up from the docking station until the cover
detaches completely (H-6 to H-8). Peel the cover seal away from the cover (H-9).
!
CAUTION
Do not remove the tub plate from the water chamber.
CLEANING YOUR HUMIDAIRE 3i
!
CAUTION
•Do not use any of the following to clean any part of the HumidAire 3i. These
solutions may cause damage and reduce the life of the product.
•bleach, chlorine-, alcohol- or ammonia-based solutions
•moisturising, antibacterial or glycerine based soaps
•water softening and unapproved descaling agents.
•Do not wash the water chamber in a dishwasher.
338284r3.book Page 10 Tuesday, November 14, 2006 1:23 PM

11
CLEANING AND MAINTENANCE
ENGLISH
WATER CHAMBER
DAILY
Wash the water chamber and tubing in warm water, using a mild detergent
(see previous caution). Use the yellow cleaning plug to assist in the cleaning process
(see steps 1 to 5 below).
Rinse them thoroughly with clean water and allow them to dry away from direct
sunlight.
WEEKLY
Inspect the water chamber for wear and deterioration. Replace the water chamber if
any component has cracked, become cloudy or pitted. Replace immediately if there is
any leaking from the water chamber.
If you notice white powder or deposits in the water chamber:
i. Fill the water chamber to the maximum water level mark with a solution of one
part vinegar to ten parts water.
ii. Let the solution soak for ten minutes.
iii. Discard the solution and rinse the water chamber with clean water.
COVER AND COVER SEAL
Inspect the cover and cover seal weekly for wear and deterioration. Replace any
damaged parts. When required, wash the cover and cover seal in warm water, using a
mild detergent (see previous caution). Rinse them thoroughly with clean water and
allow them to dry away from direct sunlight.
DOCKING STATION
Periodically wipe the outside of the docking station (including the connector seal) with
a damp cloth.
2
45
13
338284r3.book Page 11 Tuesday, November 14, 2006 1:23 PM

12
REASSEMBLING YOUR HUMIDAIRE 3i
Please refer to the illustrations in section Iof the illustration sheet.
Reassemble the parts when they are clean and dry.
1Align the cover seal to the guides on the cover (I-1) and press along the edges to
ensure it is fitted properly (I-2).
2Put one cover arm into its pivot point on the docking station (I-3) and gently flex the
other arm into its corresponding point (I-4 & I-5).
The cover should be able to open and close freely while securely attached to the
docking station.
3Replace the water chamber in the humidifier docking station (I-6).
SERVICING
With normal use of a HUMIDAIRE 3i, the water chamber needs to be replaced every
two years.
This product (HUMIDAIRE 3i) should be inspected by an authorised ResMed Service
Centre 5 years from the date of manufacture. Prior to this, the device is intended to
provide safe and reliable operation provided that it is operated and maintained in
accordance with the instructions provided by ResMed. Applicable ResMed warranty
details are provided with the device at the time of original supply. Of course, as with
all electrical devices, if any irregularity becomes apparent, you should exercise caution
and have the device inspected by an authorised ResMed Service Centre.
338284r3.book Page 12 Tuesday, November 14, 2006 1:23 PM

13
TROUBLESHOOTING
ENGLISH
TROUBLESHOOTING
If there is a problem, try the following suggestions. If the problem cannot be solved,
contact your equipment supplier or ResMed. Do not attempt to open the unit.
!
WARNING
Service and repair should only be performed by an authorised service agent.
Problem Possible Cause Solution
Device not working
(no display on LCD
screen and/or
indicator light not
lighting up)
Power cord is not plugged
in properly.
Faulty power outlet.
Flow generator and
docking station not
connected correctly.
Check that the power cord is plugged
firmly into the power outlet and the
switch (if available) is on at the outlet.
Try another power outlet.
Check that the docking station is
securely attached to the flow generator.
Indicator light
flickering
Indicator light periodically
becomes brighter to
indicate that the heating
element is active.
• Your HumidAire 3i has a rapid
heating element which allows very
short heating times. Do not be
concerned if the light only brightens
very briefly.
• Turn the dial to the setting to
switch heated humidification off. The
indicator light will remain lit to
indicate standby mode.
Indicator light is
permanently dull
and/or air does not
feel warm
HumidAire 3i reflector (see
illustration C-2a) is dirty.
Clean the reflector with a damp cloth.
Leaking water
chamber
The water chamber may be
damaged or cracked.
Cover is not attached
correctly.
Contact your supplier for a replacement.
Make sure the cover is fitted correctly.
338284r3.book Page 13 Tuesday, November 14, 2006 1:23 PM

14
No/low air flow The air tubing is not
connected properly.
The air tubing is blocked,
pinched or punctured.
The flow generator is not
working correctly.
The water chamber is
overfilled.
The cover is not latched
correctly.
The cover seal is not fitted
correctly.
Condensation is forming in
the air tube.
Connect the air tubing as described in
“Setting Up your HumidAire 3i For Use”
on page 5.
Unblock or free the air tubing. Check the
air tubing for punctures.
See the Troubleshooting section in the
flow generator manual.
Make sure that the water level is not
above the maximum water level mark.
Make sure the cover is latched onto the
docking station correctly.
Make sure the cover seal is facing the
right way up and fitted securely.
• Turn the control dial down.
• Insulate the air tubing.
Water splashing on
your face
The water chamber is
overfilled.
Condensation is forming in
the air tube and mask.
Empty some water from the water
chamber.
• Turn the control dial down.
• Insulate the air tubing.
Air does not feel
moist
The control dial is set too
low.
HumidAire 3i heating
element is not working.
Turn the control dial up.
Contact your equipment supplier.
Air too moist Control dial is set too high.
High relative humidity in
your room.
Turn the control dial down.
Adjust your humidity setting.
White powder or
deposits in the water
chamber
The water leaves scaly
mineral deposits.
• Use distilled water.
• To remove these mineral deposits, see
“Cleaning your HumidAire 3i” on
page 10.
Problem Possible Cause Solution
338284r3.book Page 14 Tuesday, November 14, 2006 1:23 PM

15
TECHNICAL SPECIFICATIONS
ENGLISH
TECHNICAL SPECIFICATIONS
PERFORMANCE
Maximum heater plate temperature: 85°C
Temperature cut-out: 93°C
Maximum output humidity: 95% relative humidity (control dial set to maximum setting,
flow rate 50 L/min, ambient temperature of 20°C, ambient relative humidity of 40%).
Maximum gas temperature: 41°C
DIMENSIONS (H XW XD)
Docking station and water chamber: 118 mm x 170 mm x 212 mm
WEIGHT
Docking station and unfilled water chamber: 670 g
Water capacity to maximum fill line: 415 mL
POWER SUPPLY
Input range for RESMED S8 flow generator with HUMIDAIRE 3i: 100–240V, 50/60Hz;
110V, 400Hz; 2.5A <140 VA (110 W) (maximum power consumption). Instantaneous
peak power consumption <340 VA.
Actual average power consumption will vary, depending on factors such as
temperature setting, set pressure, the use of accessories, height above sea level and
ambient temperature.
Maximum heater element power: 85 W.
HOUSING CONSTRUCTION
Docking station: Flame retardant engineering thermoplastic, plated cast aluminium.
Water chamber: Injection molded plastic, stainless steel.
ENVIRONMENTAL CONDITIONS
Operating temperature: +5°C to +40°C
Operating humidity: 10–95% non-condensing
Storage and transport temperature: -20°C to +60°C
Storage and transport humidity: 10–95% non-condensing
IEC 60601-1 CLASSIFICATION
Class II (double insulation)
Type CF
ELECTROMAGNETIC COMPATIBILITY
Please refer to your flow generator user's manual for details.
Note: The manufacturer reserves the right to change these specifications without notice.
338284r3.book Page 15 Tuesday, November 14, 2006 1:23 PM