Reverberi BABY S User manual

MEDICAL APPLIANCE DIVISION
Cod.
Operation and maintenance manual
STEAM STERILIZERS
MODELS
BABY S
GB

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 2 di 28
Table of contents:
1. INTRODUCTION..................................................................................................................................................................... 3
2. T E C H N I C A L S P E C I F I C A T I O N S .............................................................................................................. 4
3. G E N E R A L R E C O M M E N D A T I O N S ........................................................................................................... 6
3.1 Regulations for the operator .......................................................................................................................................... 6
4. L O C A T I O N OF T H E CON T R O L S ............................................................................................................. 7
5. S T A R T I N G A N D S E T T I N G AT W O R K ................................................................................................. 8
5.1 Removing the machine from the packing............................................................................................................................ 8
5.2 Installation and preliminary inspections........................................................................................................................... 10
6. G E N E R A L I N S T R U C T I O N S F O R U S E ............................................................................................. 13
6.1 Directions for use......................................................................................................................................................... 13
6.2 How to drain the water from the external tank ............................................................................................................ 13
6.3 End of work ..................................................................................................................................................................... 13
7. H O W TO ARRANGE T H E I N S T R U M E N T S F O R T H E S T E R I L I Z I N G
P R O C E S S ........................................................................................................................................................................... 14
7.1 Sterilizing table................................................................................................................................................................. 15
7.2 Notes and warnings ........................................................................................................................................................... 15
7.3 Monthly inspection proposal ............................................................................................................................................. 16
8. MESSAGES DISPLAYED..................................................................................................................................................... 17
8.1 Alarm management...................................................................................................................................................... 17
8.2 Operating messages ........................................................................................................................................................... 17
8.3 Printed Messages............................................................................................................................................................... 17
9.1 General maintenance (ALSO OPERATOR) ..................................................................................................................... 18
9.2 Daily routine maintenance (ALSO OPERATOR)............................................................................................................. 18
9.3 Weekly routine maintenance (ALSO OPERATOR) ......................................................................................................... 18
9.4 Monthly routine maintenance (ALSO OPERATOR)........................................................................................................ 19
9.6 Recommended inspections and replacements.................................................................................................................... 20
9.7 Corrective actions to prevent faults ................................................................................................................................... 20
WARRANTY CERTIFICATE…………………………………………………………………………………………………. 26
DECLARATION OF CONFORMITY………………………………………………………………………………………….29

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 3 di 28
1. INTRODUCTION
The machine described in this operation and maintenance manual is a steam sterilizer that has been
specially designed to sterilize most of the materials and instruments used in dental surgeries, doctors'
surgeries and hospitals in general.
The machine can either operate at a temperature of 134°C and a pressure of 2.1 Bar or 121°C and a
pressure of 1.1 Bar. These parameters are monitored and kept at constant levels by three mechanical and
electronic devices that ensure an optimal sterilizing process along with total safety.
The operating cycles can be visually checked on a display installed on the control panel of the machine,
or by means of a printer supplied on request.
The machine has been built so that the work cycle will automatically stop and the situation be indicated
by an error message on the display if the operator fails to carry out the loading operations correctly or if
a fault occurs on printer.
SYMBOLS AFFIXED TO THE MACHINE
WARNING: IDENTIFIES A HEAT SOURCE. A PART COULD BE
DANGEROUSLY HOT
WARNING: IDENTIFIES A GENERIC DANGER. THERE COULD
BE A POTENTIALLY DANGEROUS CONDITION
IDENTIFIES THE GROUND CONDUCTOR
Do not use the machine for purposes other than those for which it
has been built.
To prevent the autoclave from being subjected to electrical
disturbance, it is important to make sure that the earth resistance
value is sufficient and well coordinated with the protections in your
electrical system.
This symbol it means the product is covered by the European
Directive 2002/96/EC.
Please inform yourself about the local separate collection system
for electrical products.
Please act according to your local rules and do not dispose of
your old products with your normal household waste. The
correct disposal of your old product will help prevent potential
negative consequences for the environement and human healt.

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 4 di 28
2. TECHNICAL SPECIFICATIONS
BABY S are autoclaves designed and built in compliance with the operators' need for functionality,
practical use and safety.
Are fully automatic. All functions are electronically servo-assisted, so the operator knows what the
machine is doing at any given moment.
Have functional characteristics that make them unique, i.e.:
AUTOMATIC POWERING, thanks to which the electric heating element maintains the chamber at a
temperature of 80°C for up to 60 min., after which it will automatically switch off if not used, if the
“night” program is selected.
AUTOMATIC WATER FILLING by means of an electric pump.
AUTOMATIC AIR EXHAUST to eliminate the air from inside the chamber at the beginning of the
cycle, thus achieving the utmost steam saturation.
SAFETY VALVE to prevent overpressures.
DRYING CYCLE included: with thermodynamic system and vacuum pump
SAFETY THERMOSTAT to prevent overtemperatures.
Electronic DISPLAY for all functions, with message display and printout.
Press-moulded seamless 18/10 STAINLESS STEEL CHAMBER.
7 lt. CAPACITY chamber.
Riscaldamento graduale al fine di ottenere una temperatura più precisa e una migliore sterilizzazione.
After each cycle, the BABY S autoclave, as required, triggers an anti-condensation system unless the
door is opened within a few minutes.
POSSIBILITY OF CONNECTING THE DRAIN to the sewage system or can provided.
TANK FOR CLEAN WATER

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 5 di 28
Description
Unit of measurement
Values
Power source voltage rating
V
230 V.a.c. ~
Power source frequency
Hz
50
Machine power rating
W
1000
Boiler volume
mm
Ø 170 x 270
Operating pressure
Bar
2.1 - 1.1
Machine dimensions X, Y, Z
mm
390 x 370 x 300
Gross weight
Kg
25
Pack dimensions
mm
470 x 450 x 380
Operating temperatures
°C
+ 3°C …… + 35°C
Distance from walls
cm
8 - 10
X = depth
Y = width
Z = height
The electrical system is protected against the risk of over-currents installed inside
the machine by two 10 A delayed action fuses ( T 10 A ).
The electronic control and powering boards protect the various users by means of 3
dedicated fuses: 2 quick-acting 1 A types (F 1 A) and one 100 mA delayed action
type (T 100 mA) –(see enclosed wiring diagram).
Only have these fuses changed by a skilled electrician.
The noise level of the machine has been tested. The continuous equivalent weighted
acoustic pressure level A is less than 70 dB (A) and the continuous equivalent
weighted acoustic power level A does not exceed 85 dB (A). The measured noise
level measured is therefore very low. For this reason, the operator need not take any
particular measures (also in view of the fact that the machine operates
automatically).
DATA AND SPECIFICATIONS OF THE PRESSURIZED VESSEL:
Serial N° of vessel, Serial N° of door
Month N°, Year N° (see internal label)
Max. operating pressure:
2.4 Bar
Max. operating temperature:
160°C
Min. operating pressure:
-0.9 Bar
Test pressure:
8 Bar
Reference standards:
TRD 421
Volume of vessel:
7 lt.

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 6 di 28
3. GENERAL RECOMMENDATIONS
3.1 Regulations for the operator
Always wear personal protective equipment in compliance with the directives that establish the current
accident-preventing provisions.
Do not approach the machine with inflammable materials.

Do not carry out repairs or maintenance work whilst the machine is operating or plugged into the
electricity main or when parts of it are hot.
Only responsible adults may use the machine in places inaccessible to children.
Use the machine in a dry place, sheltered from the rain. Si raccomanda di non appoggiare sulla macchina nessun materiale nè solido nè liquido.
Periodically inspect the power cable to make sure that it is in a good condition.
If there are several persons in the place of work, remember to keep at a safe distance from the machine
to prevent accidental contact with hot parts.
Never ever operate the appliance unless the power cable is in a perfect condition and the structure
undamaged.
It is advisable to keep the door half-open with switch (8) turned off in “0” position, when the
appliance is not in use.
It is advisable to nominate a person responsible for the autoclave, as established by
directive 626/94.
Pay the utmost attention to those parts of the appliance that become hot
during operation and that still remain hot after it has been switched off.
Keep your face well away from the top part of the machine when the
door is opened to prevent it from being scalded by steam. Keep about 50
cm. away from the machine when opening the door.
As specified in the technical specifications, these autoclaves operate at a
pressure that can reach 2.2 Bar at most. Do not use the autoclave in an
improper way and do not carry out maintenance operations while the
sterilizing cycles are in progress. Remember that the pressure is shown
by the pressure gauge installed on the front of the machine itself.
Wait at least 20 minutes after the appliance has been switched off, to
allow the boiler to completely cool.

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 7 di 28
4. LOCATION OF THE CONTROLS
BABY S feature an elegant casing treated with scratch-proof epoxy powder paint in the RAL 9010
COLOUR. No particular preparations are required to operate the machines. Just fit the plug into a 230
V power socket.
CONTROL PANEL:
-1- INFO DISPLAY
-2- VALUE INCREASE / MENU’
-3- OK / ENTER
-4- VALUE DECREASE / MENU’
-5- START-STOP CYCLE
-6- PRINTER CONNECTION
-7- PRESSURE GAUGE
-8- MAIN SWITCH
-9- DOOR OPENING LEVER
-10- WATER FILL FUNNEL
-13- VISUAL LEVEL
THE FOLLOWING
ACCESSORIES ARE SUPPLIED:
1 TRAY HOLDER, 2 TRAYS, 1
TOOL TO TAKE OUT THE TRAYS
AND ADJUST THE DOOR, 1
SPONGE, 1 INSTRUCTION
MANUAL, 1 10 LITER CAN.

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 8 di 28
5. STARTING AND SETTING AT WORK
5.1 Removing the machine from the packing
The machine is consigned packed on a wooden pallet in a cardboard box: make sure that there are no dents
and that the wrapping is in optimum conditions.
The machine must be stored in a dry place, sheltered from adverse weather conditions, at a temperature
between +3°C and +35°C. The machine must be handled without jolting and using appropriate means.
Open the pack without overturning it. Remove the polystyrene from the top and sides (the weight of the
model is given in chap. 2, technical specifications).
Lift the machine out of the box in a vertical direction using the 2 hooks supplied in the bag inside the pack.
These should be inserted into the two holes at the sides of the casing (see drawing on page 9). Remove the
pluriball wrapping from around the machine and make sure that all parts of this latter are undamaged and
complete with all the accessories indicated on the consignment note. Immediately notify our dealer if
discrepancies are discovered.
Keep the packing materials for as long as the machine remains in use, not just for the warranty period. This
is because the autoclave may need to be calibrated or regulated by the manufacturer's staff of by an after-
sales center. Non-original packing is unable to ensure that the machine is correctly protected during
transport.
The original packing comprises the following items:
- BIWALL BOX IN CARDBOARD WITH 3 CORRUGATIONS
- PLURIBALL POLYETHYLENE BAG
- SHAPED POLYSTYRENE FOAM
- PALLET INSIDE THE BOX

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 9 di 28
DRAWING ILLUSTRATING HOW THE MACHINE MUST BE LIFTED FROM THE PACK

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 10 di 28
5.2 Installation and preliminary inspections
The installer is obliged to make sure that the place in which the sterilizer is installed
is fit for that purpose (CEI 62/4).
Install the autoclave in a well ventilated place, well away from sinks, heat sources, grinders and from all
other machines.
Comply with the following instructions to simply and efficiently check that the machine has been
positioned correctly:
Fit the electric plug into a socket WITH A CAPACITY OF AT LEAST 10 Ampere AND
EQUIPPED WITH AN EARTH CONNECTION. Make sure that the mains voltage rating
corresponds to the value indicated on the label at the rear of the machine (230 Volts).
BABY S must only be filled with DISTILLED WATER to ensure that the electrical and air-operated
devices operate efficiently and are long lasting.
Never connect the plug of the machine to a reduction.
Use a bubble level to make sure that the surface on which the appliance is
to be positioned is perfectly horizontal.
Fill out and send off the warranty form.

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 11 di 28
DESCRIPTION OF THE REAR PART
1) Pipe can.
2) Water drainpipe used for
connecting to the can
through "1". The same
pipe can be used for
draining into the sewage
system.
3) Label showing the
following data: Model,
CE mark, power voltage
and frequency, power
input, serial number, year
of manufacture,
manufacturer's details.
4) Power group.
5) Safety valve guard.
6) Thermostat manual
rearmament.
LANGUAGE SETTING:
With the door open and the machine on, scroll through the menu using key (2) or (4). Besides the
sterilisation cycles, machine setting data can be displayed in succession (temperature in the chamber etc.).
Enter the desired item and confirm with key (3). Change the figures with keys (2) and (4).
Once desired changes have been made, always confirm with key (3).
TABLE OF CYCLES END SERVICES:
Nr. Progressiv
Cycle or service
1
CYCLE FREE
2
CYCLE FREE
3
CYCLE 121° UNWRAPPED
4
CYCLE 121° WRAPPED
5
CYCLE 134° UNWRAPPED
6
CYCLE 134° WRAPPED
7
CYCLE 134° PRIONE
B & D TEST
BOWIE & DICK TEST
DRY FN
CYCLE DRY
FIALE
CYCLE PHIALE
NIGHT
CYCLE NIGHT S/N
PRINTER
PRINT S/N
LANGUAGE
LANGUAGE GB/F/D/E/I

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 12 di 28
READ OF INFO DISPLAY:
3
1
5
5
3= Cycle number 15= Sterilization time 5= Dry time
121= Temperature of sterilization °C
..
1
2
1
4
2
0
1
5
4= Cycle number 20= Sterilization time 15= Dry time
121= Temperature of sterilization °C
..
1
2
1
5
4
5
5= Cycle number 4= Sterilization time 5= Dry time
134= Temperature of sterilization °C
..
1
3
4
6
1
0
1
5
6= Cycle number 10= Sterilization time 15= Dry time
134= Temperature of sterilization °C
..
1
3
4
7
1
5
2
0
7= Cycle number 15= Sterilization time 5= Dry time
134= Temperature of sterilization °C
..
1
3
4
B
&
D
T
E
S
T
BOWIE & DICK TEST not for instruments
134= Temperature of sterilization °C
..
D
R
Y
F
N
ADDITIONAL DRY
110= Temperature of sterilization °C
..
B
O
T
T
L
E
PHIAL CYCLE
54= Temperature of sterilization °C for 48 hour
..
N
I
G
H
T
F
N
NIGHT CYCLE
YES= Active NO= Inactive
Y
E
S
/
N
O
P
R
I
N
T
E
R
PRINTER SELECTION
YES= Active NO= Inactive
Y
E
S
/
N
O
L
A
N
G
U
A
G
E
LANGUAGE SELECTION
..
N
.
C
Y
C
L
E
S
NUMBER OF CYCLES
..
W
A
I
T
>
6
5
Chamber very hot. To attend the cooling.
P
L
E
A
S
E

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 13 di 28
6. GENERAL INSTRUCTIONS FOR USE
6.1 Directions for use
OPEN DOOR WITH SWITCH (9) TURNED.
-Remove the tray holder pack from the chamber.
-Switch on the master switch (8).
-The display unit will indicate lack of water with the message NO WATER IN TANK.
- to pour with caution the water in the funnel (10).
- Check the filling operation through window (13) and wait for the acoustic signal indicating that the
maximum level has been reached.
-The display (1) unit will show the number of the previously performed cycle.
-If a different cycle to that shown on the display unit (1) is to be performed, press button (2) or (4) to
scroll the menu.
-For a customised ("special") cycle, select cycles number one or two. Once a "special" cycle has been
selected, press key (3) to change the settings made. It is possible to change the sterilisation time, the
drying time, the sterilisation temperature. Refer to the cycle table on page 15.
-After terminating the settings on the display unit (1), introduce the tray holder into the chamber with
the load to be sterilised.
-To start the cycle, close the door with the handle (9).
-Press key (5) to start the cycle.
-The end of the cycle is indicated by a message on the display unit (1).
6.2 How to drain the water from the external tank
-Chek the tank level (used water) bifore each cycle.
-In case the level is nearly full, please beh ave as follows:
-Unscrew the plug of the tank.
-Empty the tank in drainage and rinse with care.
-Screw the plug of the tank (make attention to not twist the discharge tube and be sure that the tank is in
stable position.
6.3 End of work
At the end of the operations, open the door and position the green master switch (8) on OFF.
Pay particular attention to the temperature of the various components
when you switch off the machine.
Wait a few minutes to allow the components to cool.

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 14 di 28
7. HOWTO ARRANGE THE INSTRUMENTS FOR
THE STERILIZING PROCESS
Before being sterilized, the instruments must be cleaned to remove blood residues, incrustations, foreign
bodies, etc. These impurities can damage the items being sterilized, the autoclave components and
prevent the sterilizing process from being correctly carried out.
These instruments must be made of NO-ferrous material since they could damage or oxidize the other
instruments or the autoclave itself.
To achieve perfect sterilizing, it is therefore important to proceed in the following way:
1. Rinse and brush the instruments under running water immediately after use to remove all deposits.
2. Place the instruments in the ultrasound machine with distilled water and detergent solution if
possible.
3. Thoroughly rinse the instruments in demineralised water to prevent scaling stains.
4. Dry the instruments to eliminate all water residues which could lead to oxidation.
5. Wash, rinse and dry the supplied trays and make sure that they are perfectly clean.
6. To ensure that packaged instruments are perfectly dried, we recommend use of support art. M9050
supplied as an optional.
7. If loose instruments must be sterilized, it is advisable to cover the trays with a paper or fabric napkin
to prevent direct contact with the tray surface: do not place the instruments straight on to the trays.
8. Scissors and forceps should be slightly opened. Mirrors and containers should be placed upside
down for the sterilizing process.
9. It is advisable to keep the instruments separated from each other to achieve a better sterilizing action.
Overloading will impair the sterilizing process.If packaged instruments must be sterilized on the
trays, place the packets with their transparent side downwards and do not overlap. The packets
should not be too large. Drying will be difficult if their edges overlap.
10. The machine can operate with a maximum 3 Kg load.
Sterilizing handpieces:
Carefully read the handpiece operation manual with particular attention to the part about sterilizing
(121°).
Wrap the handpiece in the special sterilizing cloth.
Place the wrapped handpiece on a NON-perforated tray to prevent spilt lubricating oil from polluting
the pipes of the autoclave.
Proceed with a short cycle 121°C sterilizing program.
Remember to immediately remove the handpiece from the autoclave at the end of the sterilizing
process.
For a valid sterilizing process, it is obligatory to add a chemical indicator for each cycle.

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 15 di 28
7.1 Sterilizing table
CYCLES FREE
STERILIZING TIME (Min.)
DRYING TIME (Min.)
1
*
*
2
*
*
CYCLES AT 121°
STERILIZING TIME (Min.)
DRYING TIME (Min.)
3 UNWRAPPED
15
5
4 WRAPPED
20
20
CYCLES AT 134°
STERILIZING TIME (Min.)
DRYING TIME (Min.)
5 UNWRAPPED
5
5
6 WRAPPED
10
20
7 PRIONE
18
20
TEST
STERILIZING TIME (Min.)
DRYING TIME (Min.)
BOWIE & DICK*
3,5
2
CYCLE PHIAL
STERILIZING TIME (Min.)
54°
48h (Total length of test)
* Preset value.
7.2 Notes and warnings
1- Strictly comply with the manufacturer's instructions when sterilizing materials.
2- To preserve packaged and loose sterilized materials, the trays must be stored in special cabinets fitted
with ultraviolet lamps and designed for this specific use.
3- Whenever a sterilizing process is carried out, it is advisable to add a chemical indicator that we can
supply on request, code 1468.
4- It is advisable to purchase a printer with date stamp code M 9003 to file and record the sterilizing
cycles and any faults that may have occurred.
5 - There must always be trays and tray-holders in the chamber. Without these accessories, abnormal
pressures and temperatures could develop inside and these could cause the cycle to abort.
6 - It is advisable to place a phial containing culture spores in the chamber along with each load sterilized
in order to make sure that the sterilizing process is valid.
7 - If the packets are not perfectly dry at the end of the sterilizing process, proceed with the supplementary
drying cycle with cycle (DRY FN).

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 16 di 28
7.3 Monthly inspection proposal
Fac simile of an inspection form
Sterilizer data
Brand
Model
Year of purchase
Observations
Periodical internal inspection
Date
Cycle length on
display
Cycle temperature
Cycle temperature
07/11/2000
20’
134°
VAPOR LINE
The utilized indicator is enclosed for each inspection.
Always use biological indicators. 3 types of integrator are indicated as an alternative.
ORIGINAL
.
VAPOR L I N E
(COD.1468)
T H E R M A L O G S
VEER
EXAMPLE

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 17 di 28
8. MESSAGES DISPLAYED
8.1 Alarm management
MESSAGE
ERROR TYPE
REMEDY
NO POWER
No mains power
Fit the machine plug in a single socket that complies with standards
and is without adapters or extensions. Change the fuse and check the
causes. Make sure the master switch (8) is not turned off with closed
door.
NO WATER IN TANK
Not enough clean water in load tank
Fill up
HIGH
High temperature
Check generator solenoid valve and temperature probe cable (PT100)
LOW
Low temperature
Check solenoid valve, thermostat and heating element of
generator. Clean the generator probe.
VACUUM
Vacuum error
Check the vacuum pump and the relevant solenoid valve. Check the vacuum
values on the display unit and on the pressure gauge.
MAX TEMP.
High boiler pressure
Check the temperature probe (PT100) and cable or
detached cable.
PRESS. ERR.
Pressure error
Check for any leaks. Check for any heating element malfunctions.
To reset the machine, turn the switch (8) off and on.
8.2 Operating messages
MESSAGE
OPERATION IN PROGRESS
Phials
Pre-sterilised phial culture cycle
Print.
Start print
No cycle
Maintenance of instrumental drying
no. cycles
No. of cycle performed by machine
Italian
Current language (set)
End
Cycle finished
8.3 Printed Messages
MESSAGE
OPERATION
Ster. time
Sterilisation time
1
Type of cycle
Cycle type
2
Ster. time
Sterilisation time
3
Min.
Cycle min.
4
Sec.
Cycle sec.
5
C
Degrees centigrade
6
Sterilisation
Sterilisation phase
7
Drying
Drying stage
8
End
End of cycle
9
Total time
Total cycle time
10
Test
Test cycle
11
Release
Steam release
12
Stopped
Cycle stopped by operator
13

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 18 di 28
9. MAINTENANCE
Carry out the maintenance operations with the machine at a standstill, after having
removed the plug from the power socket and after having allowed the components to
cool down.
The declaration of conformity to the standards in force is not valid unless the
maintenance operations described below are carried out.
9.1 General maintenance (ALSO OPERATOR)
The machine needs to be serviced in a particular way. Users are therefore advised to comply with the
below listed recommendations:
Periodically check the condition of the electrical system with particular attention to the connection
cable. Contact our Technical Assistance Service or specialized personnel if faults are
discovered.
Periodically clean the door, the seal and take particular care when cleaning the internal part of the
boiler, removing any scaling with the damp sponge (supplied with the machine). Correct cleaning of
these parts of the machine will ensure that the sterilizing cycle takes place in the right way.
If the machine is not to be used for a long period of time, leave the door ajar and store it at a room
temperature of >8°C.
Use a damp cloth to clean the casing of the machine. Never ever use inflammable liquids for any
reason whatsoever.
9.2 Daily routine maintenance (ALSO OPERATOR)
Clear the door seal, door window and generally clean the outer and inner surfaces of the machine.
Clean the black silicone door seal, the outer and inner edges and the part where the door rests on the
sterilizing chamber and on which the seal must tightly fit. Use the supplied sponge to do this. The soft
part of the sponge can be used to clean the seal while the rough part can be used to clean the edge of the
chamber.
This cleaning operation must be carried out regularly to remove all impurities that could lead to loss of
pressure inside the sterilizing chamber.
Check the used water level and drain off the actual water into the sewer if necessary. Then wash out the
can under running water.
Check the level in the used water can
9.3 Weekly routine maintenance (ALSO OPERATOR)
Cleaning the sterilizing chamber (cleaning the trays and tray holders.
As specified in section 9.1 “ General maintenance “, all traces of deposits must be removed from the
bottom of the chamber. Use the rough side of the supplied sponge for this operation, attempting to
eliminate any scaling that may have formed.
Rinse everything with the same water used for the sterilizing process. The trays and tray-holders must
also be cleaned in this way.

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 19 di 28
9.4 Monthly routine maintenance (important)
Lubricate the pins and locking mechanisms.
Check the movement of the hinge and door locking pin. Lubricate with Vaseline oil.
Make sure that the door is well regulated. If it is excessively slack, it must be adjusted by means of the
supplied wrench. Turn the regulator at the rear of the door in a (A) direction. This will increase the
pressure exercised by the seal.
Attempt to shut the door. If some difficulty is encountered, turn the regulator in an (B) direction with the
supplied wrench.
Clean the entire autoclave cabinet with a slightly damp sponge, including the door casing.
Check and/or replace bacteriological filter Code. 1067 once a year.
9.5 Periodic extraordinary maintenance(ONLY FOR TECHNICIANS)
To allow the autoclave to operate in a regular way, the manufacturer advises users to carry out a
functional test to ensure that the temperature and pressure parameters of the machine comply with the
standards required for a correct sterilizing process.
These tests must be conducted by personnel authorized by the manufacturer, using calibrated and
periodically certified instruments.
The autoclave can also be sent to the manufacturer for this test, after form pag. 24, has been filled out
and accepted.
The autoclave is able to accept probes for the sterilizing tests.
It is advisable to have the appliance subjected to a Total Overhaul by After-sales Service staff at least
once every 12 months.

Operation and Maintenance Manual –Steam sterilizers mod. BABY S
Rev. 01 del 01-07-2013 - C:\Documenti\Manuali di istruzione\BABY S GB-R01.doc
Pag. 20 di 28
9.6 Recommended inspections and replacements
(ONLY FOR TECHNICIANS)
1) Make sure that the safety valve functions correctly.
-Remove the conveyor tube
- Carry out the 134° cycle and when the maximum pressure has been reached (2.2 bar), unscrew and
retighten the knurled ring nut on the safety valve.
- Check to make sure that steam issues by unscrewing the ring nut and, vice versa, that total retention is
achieved by tightening the same knurled ring nut again.
2) Replace the filter down the can.
3) Clean and inspect the sterilizing chamber (there must be no trace of scaling or coloured tarnishing)
4) Make sure that the cock (12) is not clogged by blowing through it with a little compressed air.
5) Make sure that the micro and micro-pressing system allows the door to close correctly. Lubricate with a
silicone spray.
6) Replace the filter on the water fill line.
7) Replace load pump.
Intervention date…………………………signature of the authorized technician………………………
N.B. to send back as photocopy if the building factory required it.
9.7 Corrective actions to prevent faults
1) Change the water inlet filter (internal) code 1484.
2) Clean the "Y" shaped filter (if installed) code 3136, and replace its seal, code 3188.
3) Replace the diaphragm and head seal of the vacuum pump (specify the model or serial number of the
machine).
4) Replace the N.O. solenoid valve or coil, code 1015.
5) Before closing up the machine, generally inspect the internal components to make sure that they are in a
good condition.
6) After these operations have been carried out, print out the report on the first cycles to make sure that the
sterilizer operates in a normally efficient way.
7) Check the temperature and pressure in the chamber with a special “logger” type instrument.
8) Send the report of inspection and replacements.