Revo RESPTZ36-3 User manual

INSTRUCTION MANUAL
REVO ELITE 36x IR
SPEED DOME CAMERA
Model#: RESPTZ36-3

II
Please read this manual thoroughly before use and keep it handy for future reference.

I
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO
NOT INSERT ANY METALLIC OBJECTS THROUGH THE
VENTILATION GRILLS OR OTHER OPENINGS ON THE
EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.

II
FCC COMPLIANCE STATEMENT
FCC INFORMATION: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CAUTION: Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

III
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
15. CAUTION –THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER
THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS
UNLESS YOU ARE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed
Class 2 power source only.

IV
Table of Contents
Chapter 1 —Introduction..................................................................................................... 1
1.1 Features..................................................................................................................................... 1
Chapter 2 —Installation and Configuration..................................................................... 2
2.1 Package Contents.................................................................................................................... 2
2.2 Installation................................................................................................................................. 2
2.1.1 Installation - Wall Mount.................................................................................................. 3
2.1.2 Installation - Ceiling Mount............................................................................................. 4
2.3 Basic Configuration of Camera System .............................................................................. 5
2.4 Setting Dome Camera Address (ID) ..................................................................................... 6
2.5 Setting Dome Camera Protocol............................................................................................. 8
2.6 Connections Setting Dome Camera Termination.............................................................. 9
2.7 Connections.............................................................................................................................10
2.8 Getting Started ........................................................................................................................11
Chapter 3 —Program and Operation .............................................................................. 12
3.1 Dome Camera Selection........................................................................................................12
3.2 Accessing the On-Screen Menu Utility...............................................................................12
3.3 How to control the On-Screen Menu Utility .......................................................................12
3.4 Auto Scan (Shortcut: SCAN) ...............................................................................................13
3.5 Preset (Shortcut: PRST).......................................................................................................15
3.6 Shortcut of Preset Program..................................................................................................17
3.7 Tour (Shortcut: TOUR) ..........................................................................................................17
3.8 Pattern (Shortcut: PTRN) ......................................................................................................18
3.9 Alarm.........................................................................................................................................19
3.10 Area Title ................................................................................................................................20
3.11 Privacy Zone..........................................................................................................................21
3.12 Camera Menu.........................................................................................................................22
3.13 Dome Setup ...........................................................................................................................27
3.14 Dome Communication .........................................................................................................33
3.15 Function Run.........................................................................................................................34
3.16 Motion Setup .........................................................................................................................35
Appendix A —Specifications ........................................................................................... 36
Appendix B —Troubleshooting ....................................................................................... 38
Appendix C —Glossary ..................................................................................................... 39
Appendix D —Short Cut Key............................................................................................ 41

1
Chapter 1 —Introduction
1.1 Features
The dome camera and the keyboard controller make up the building blocks for any surveillance/security
system. Using multiple Keyboard Controllers and multiple dome cameras, no place is too large for
monitoring. Extensible and flexible architecture facilitates remote control functions for a variety of external
switching devices such as multiplexers and DVRs.
·Built-in optical power zoom camera with True Night Shot function.
·Built-in Synchronized IR LED & Fixed IR LED:
The camera is equipped with two built-in IR LED’s, fixed one for wide view and zoom synchronized
adjustable one for distant view.
·240 Preset positions
·8 Tours consist of Preset, Pattern, Auto-Scan and other Tours can be programmed with over 300
functions and Preset location. While moving, each Preset scan can be watched in smooth Vector Scan
mode.
·16 Auto Scans with the normal, the vector, and the random mode and the Endless Auto-Pan with 13
speed steps.
·8 Patterns (up to 500 second) and 8 Privacy zones
·16 Area Titles
·4 Alarm inputs, 1 TTL Alarm output, 1 Relay Alarm output (NC & NO)
·Variable speed from 0.1°/sec to 380°/sec
Three Variable speed (SLOW, NORMAL, TURBO)
Turbo speed is Max 250°/sec with Ctrl key pressed.
·Pan / Tilt speed is inversely proportional to the zoom ratio with the option.
·Maximum speed is 380°/sec when preset command.
·Tilt range is -10°to 90°
·Programmable user preferences (alarm, preset, title, etc.)
·90°Auto Flip
·Up to 999 selectable camera addresses (3999 by software setting).
·Multi-language Menu Display, Password Confirmation
·Function Run menu using DVR without function key (Pattern, SCAN, …)
·Built-in RS-485 receiver driver
·12VDC for dome
·Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

2
Chapter 2 —Installation and Configuration
2.1 Package Contents
The package contains the following.
Dome Camera 1
Instruction Manual (This Document) 1
2P screw type Connector 1
5P screw type Connector 2
12VDC Adaptor 1
2.2 Installation
You need one optional mount kit of the wall mount and the ceiling mount to install.
The wall or ceiling mount must be attached to a structural object such as hard wood, concrete that will
support the weight of the mount and dome camera.
The use of a solid backboard is recommended when attaching to gypsum walls.
1. Remove the Protection pad and the tape from attached the dome camera.
2. Attach the mounting base to wall using the supplied M8 tapping screw and plastic bushing. (Ceiling
using the supplied M6 tapping screw and bushing)
3. Wind the both thread of the pipe end with Teflon tape about 20 times for sealing. Then use a silicone
rubber sealant to seal the area where the wall (ceiling) mount and the pipe meet.
4. Place a bead of silicone sealant around the wall and ceiling mount mounting flange, press it to the
surface and line up the flange hole with drilled holes.
CAUTION 1: A silicone rubber sealant must be applied to seal the housing to secure waterproofing.
CAUTION 2: When installing, a bracket must be applied.

3
2.1.1 Installation - Wall Mount
The wall mounting plate must be attached to a structural object such as concrete that will support the
weight of the mount and Dome Camera.
1. Select a suitable mounting location and verify there is sufficient cable to reach the middle of the Wall
Mount.
2. Mark and drill mounting holes in the surface using the Wall Mount Flange.
3. Pull out cables required to connect to the dome camera from the wall or route cables through a
section of 0.75 in. (19 mm) conduit pipe.
4. Remove the access plate from the wall mount bracket.
5. Attach the wall mount bracket using screws routing cables through the access plate’s hole.
6. Attach the housing’s safety wire to the wall mount’s latch.
7. Fix the housing to the wall mount bracket using the locking nut after routing cables through the wall
mount bracket and tighten the housing set screw with the supplied wrench.
8. After connecting cables, attach the access plate.

4
2.1.2 Installation - Ceiling Mount
The ceiling mounting plate must be attached to a structural object such as concrete that will support the
weight of the mount and Dome Camera.
1. Select a suitable mounting location
and verify there is sufficient cable
to connect with cables from the
housing.
2. Mark and drill mounting holes in
the surface using the ceiling
mount flange.
3. Pull out cables required to connect
to the dome camera from the
ceiling.
4. Attach the ceiling mount bracket
using screws routing cables
through the locking nut.
5. Tighten the housing with the pipe
using the socket after routing
cables through the pipe.
6. Attach the housing's safety wire to
the ceiling mount's m6X35
tapping screw.
7. After connecting cables, fix the
pipe to the ceiling mount using the
locking nut.
8. Tighten set screws of the socket
and locking nut with the supplied
wrench.

5
2.3 Basic Configuration of Camera System
No. CONNECTOR COLOR DESCRIPTION
1 DC JACK BLACK 12VDC
2 BNC Cable BLACK VIDEO OUTPUT
3 5P Cable
RED ALARM INPUT 1
ORANGE/WHITE ALARM INPUT 2
ORANGE ALARM INPUT 3
GREEN/WHITE ALARM INPUT 4
BLACK GND
4 5P Cable
BLUE ALARM OUTPUT
GRAY GND
GREEN COM (RELAY)
VIOLET NO (RELAY)
PINK NC (RELAY)
5 2P Cable BROWN RS485+(A)
BROWN/WHITE RS485-(B)
6 1P Cable YELLOW/GREEN F_GND
The camera must be installed by qualified service personnel in accordance with all local and federal
electrical and building codes.

6
2.4 Setting Dome Camera Address (ID)
When the COMMUNICATION MODE is set to S/W
Dome camera address (ID) and Protocol can be used by selecting from the MENU.
You can call up the On-screen menu utility on your monitor by pressing MENU key on the keyboard
controller, the following On-screen menu utility will appear:
Select the”DOME COMMUNICATION”and set the desired idem by twist the Joystick
See Chapter 3 —Program and Operation for DOME COMMUNICATION.
If you want to set the address more than 999, you should contact the service provider.
NOTE: COMMUNICATION MODE is set to S/W, the Hardware (H/W) setting is ignored.
DOME MENU
AUTO SCAN
PRESET
TOUR
PATTERN
ALARM
AREA TITLE
PRIVACY ZONE
CAMERA
DOME SETUP
DOME COMMUNICATIOM
FUNCTION RUN
EXIT(ESC TO EXIT)
DOME COMMUNICATION SETUP
COMMUNICATION MODE : S/W
DOME ID 0001
PROTOCOL AUTO
BAUDRATE 9600
PARITY NONE
SAVE AND EXIT(ESC TO CANCEL)

7
When the COMMUNICATION MODE is set to H/W
Dome camera address (ID) and Protocol can be used by selecting from the Hardware.
To prevent damage, each dome camera must have a unique address (ID). When installing multiple dome
cameras using a multiplexer, it is suggested that the dome camera address match the multiplexer port
number.
If you want to set the address more than 999, you should contact the service provider.
Example: Port 1 = Dome 1, Port 2 = Dome 2 …Port 16 = Dome 16. If more than 16 dome cameras are
installed using two or more multiplexers, ID of the dome camera should be ID of MUX x No. of camera IN.
(e.g. multiplexer ID= n, Camera IN= m then ID of Dome =16x
(n-1)+m )
Refer to Figures 1-2 for setting the dome camera address (ID) and protocol selection.
Figure 1 –Setting Dome Camera Address (ID)
1
2
3
4
5
6
7
8
9
0
8
1
1
2
3
4
5
6
7
8
9
0
8
1
1
2
3
4
5
6
7
8
9
0
8
1
S3
S2
S1
DOME ID S3 S2 S1
1 0 0 1
2 0 0 2
. . . .
999 9 9 9

8
2.5 Setting Dome Camera Protocol
If a dome camera is to be installed with a Fastrax keyboard controller,
select the default protocol.
Consult service personnel if a dome camera is installed with device other than a keyboard controller.
S/W On Off FUNCTION
D1
S4
-
1
En
able
Disable
Alarm
D2 S4-2 PAL NTSC NTSC/PAL
D3 S4-3 Reserved
D4
S4
-
4
On
Off
Termination
D5 D6 D7 D12 PROTOCOL
S5-1 S5-2 S5-3 S6-4
Off
Off
Off
Off
F2,F2E,
Pelco
-
D,Pelco
-
P
:
default
Off Off On Off F2,F2E
Off On Off Off Sensormatic RS422
Off
On
On
Off
Pelco
-
D,
Pelco
-
P
On
Off
Off
Off
Vicon
On Off On Off Ernitec
On On Off Off Reserved
On
On
On
Off
F2
Off Off Off On Philips(Bosch)
Off Off On On Reserved
Off
On
Off
On
Dynacolor
Off
On
On
On
Reserved
D8
D9
D10
BAUD RATE
S5-4 S6-1 S6-2
Off Off Off 2400 bps
Off
Off
On
4800 bps
Off
On
Off
9600 bps (Default)
Off On On 19200 bps
On Off Off 38400 bps
D11 PARITY BIT
S6-3
Off
None
On Even
Figure 2 –Protocol Selection Switches
NTSC
PAL
o
n
o
n
S4 S4

9
2.6 Connections Setting Dome Camera Termination
The device which is connected at end of line, whether it be a dome camera or keyboard controller, must
have the cable for communication terminated by setting the appropriate DIP switch. Without proper
termination, there is potential for control signal errors. Total length of the cable for communication should
not exceed 4000ft (1.2km).
Figure 3- Termination Diagram

10
2.7 Connections
•Connecting to the RS485
The dome camera can be controlled remotely by an external device or control system,
such as a control keyboard, using RS485 half-duplex. Connect Marked RS_485+(A), RS_485-(B) of the
RS485 control system.
•Connecting Video output connector
Connect the video output (BNC) connector to the monitor or video input.
•Connecting Alarms
AL1 to 4 (Alarm Input)
You can use external devices to signal the dome camera to react on events. Mechanical or electrical
switches can be wired to the AL (Alarm Input) and GND (Ground) connectors.
See Chapter 3 —Program and Operation for configuring alarm input.
GND (Ground)
NOTE: All the connectors marked GND are common.
Connect the ground side of the Alarm input and/or alarm output to the GND connector.
TTL Out 1, Relay Out 1 (TTL : 5V Output, Relay : Normal Close or Normal Open)
The dome camera can activate external devices such as buzzers or lights. Connect the device to the
Alarm out and GND or the NC(NO) (Alarm Out) and COM (Common) connectors.
See Chapter 3 —Program and Operation for configuring alarm output.
Connecting the Power
Connect the power of 12VDC 5A to the dome camera.
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

11
2.8 Getting Started
Once installed apply power to the dome camera. The dome camera will start a configuration sequence.
OSD Position
The dome can move the OSD position in the OSD position setup.
OSD Position Setup
001 AF AE
EMPTY DATA
DOMEID:0001
ALARM:1 W→360.0,090.0
(AREA TITLE) (AF AE)
(FUNC TITLE )
(CTRL KEY TO MOVE)
SAVE AND EXIT(ESC TO CANCEL)
(ALARM MESSAGE) (DOME ID…)
(ANGLE…)
INFORMATION
DISPLAY
FUNCTION
UNDER RUNNING
ALARM DISPLAY
CAMERA TITLE
CAMERA ID
VIEW DIRECTION
PAN & TILT ANGLE
PRESET TITLE
AREA TITLE STATUS of
FOCUS and AE

12
Chapter 3 —Program and Operation
3.1 Dome Camera Selection
Before you program or operate a dome camera, you must select the dome camera by pressing the dome
camera No. + CAM
Example:Pressing 1, 0and CAM key sequentially will select dome camera 10. The selected dome
camera ID will be displayed on the LCD monitor of the keyboard controller.
3.2 Accessing the On-Screen Menu Utility
You can call up the On-screen menu utility on your monitor by pressing MENU key on the keyboard
controller, the following On-screen menu utility will appear:
3.3 How to control the On-Screen Menu Utility
Function Button
Call the On-screen menu utility MENU
Navigate through the menu items. Joystick up or down
Go into the sub-menu items. Joystick left or right
or IRIS Open
Change value.
Enter the editing title mode.
Joystick left or right or
Zoom handle twist or
Tele , Wide
Change value of angle CTRL + Joystick
Enter the changing angle mode. IRIS Open
Exit the changing angle mode. IRIS Close
Escape (EXIT) ESC
DOME MENU
AUTO SCAN
PRESET
TOUR
PATTERN
ALARM
AREA TITLE
PRIVACY ZONE
CAMERA
DOME SETUP
FUNCTION RUN
EXIT(ESC TO EXIT)

13
3.4 Auto Scan (Shortcut: SCAN)
The Auto scan supports up to 17 programmed angles at user-programmable speeds. Follow these steps
to program Auto Scan:
NUMBER :01 -08, 10-17, 09:AUTO PAN mode
TITLE :up to 12 characters.
MODE :NORMAL, VECTOR, RANDOM (AUTO PAN mode :NORMAL, RANDOM only)
NORMAL: Move from start point to end point in panning only.
VECTOR: Move from start point to end point including tilt and zoom simultaneously and
linearly. In some model, the zoom is fixed at wider angle and the zoom magnification
information is not displayed.
RANDOM: Move randomly between the start point and the end point.
SPEED : 1 - 13 step, the lower number means the slower speed.
SCAN DIR : Set the scan direction, CCW(Counter Clock Wise), CW(Clock Wise)
SWAP : Swap the start point for the end point.
DWELL : Set the dwell time at the both end, 01 –99 seconds
1. Press the SCAN key to enter the auto scan menu directly. Or press the MENU key to display the main
menu on the monitor. Scroll to Auto Scan and push the Joystick to the right.
2. Select the”NUMBER”and set the desired number by pushing the Joystick left or right.
3. Select the “TITLE”and twist the Joystick to enter the title edit mode.
4. Twist the Joystick by changing the alphanumeric characters and move the next position. Or move
down to the character table and press CTRL or IRIS OPEN at the desired character then the cursor
position moves to the next position automatically. Push the Joystick left or right at the “ALL DELETE”
field to delete all characters. Push the Joystick left or right at the “EXIT”field to finish title edit menu.
AUTO SCAN SETUP
NUMBER : 01
TITLE : A01
MODE : NORMAL
SPEED : 5 STEP
START ANGLE : ----- -----
END ANGLE : ----- -----
SCAN DIR : CCW
SWAP : OFF
DWELL : 03 SEC
SAVE AND EXIT(ESC TO CANCEL)
TITLE EDIT MENU
A01
*
A B C D E F G H I J
K L M N O P Q R S T
U V W X Y Z 0 1 2 3
4 5 6 7 8 9 ( )
ALL DELETE
EXIT (ESC TO EXIT)

14
5. Select “MODE”and “SPEED”.
6. Select “START ANGLE”. Hold down the CTRL key while selecting the start position using the Joystick.
Current panning position will be displayed. Release CTRL key to complete the selection of the start
position. Or Press IRIS Open then the “CTRL”displays. Move the desired position and the zoom
position. Press IRIS Close then the “CTRL”disappears. To adjust at the 0.1 degree interval, twist the
Joystick at the pan field and the tilt field. To adjust at the one zoom interval, twist the Joystick at the
zoom field.
7. Select “END ANGLE.”Hold down the CTRL key while moving the Joystick to select the end position.
The end position angle should be larger than start position. Release the CTRL key to complete the
selection of the end position. Or Press IRIS Open then the “CTRL”displays. Move the desired position
and the zoom position. Press IRIS Close then the “CTRL”disappears. To adjust at the 0.1 degree
interval, twist the Joystick at the pan field and the tilt field. To adjust at the one zoom interval, twist the
Joystick at the zoom field.
8. Set “SCAN DIR”to CCW or CW.
9. Select “SWAP”. Set to ON, to exchange the start angle and the end angle.
10. Set “DWELL TIME”.
11. Select Save and Exit and push the Joystick to the right or press IRIS Open. Press ESC or IRIS
Close to exit the program without saving.
Pressing the HOME key delete stored data at the angle field.
To set the position using the preset position:
a. Before entering the Auto Scan menu, select a preset position as a starting point for
Auto Scan.
Example:2+ PRST and do step 1 to 4. In step 5, just press the Ctrl key at the start angle position, the
current position will be displayed as a start position.
b. Save and exit from the menu.
c. In normal mode, call a preset to be the end point of scan. Press 3+ PRST then press Scan key to
enter the Auto Scan menu. Move the cursor position to END ANGLE. Just press CTRL key at the end
angle position. Save and exit from the menu.
Press SCAN key on the angle field to display with the small OSD. Then the screen will show as below.
The setting procedure is the same as above.
NOTE: 09:AUTO-PAN mode(Endless panning)
AUTO SCAN AREA SETUP
(CTRL KEY)
NUMBER01
START: ----- ----- ---
END : ----- ----- ---
EXIT(ESC TO EXIT)