Revox M30 User manual

User Manual
Multiuser Amplifier
M30

Overview and content
Introduction ........................................................................................................................................................3
Unpacking .................................................................................................................................................................................3
Network requirements for M30................................................................................................................................................3
Included in delivery...................................................................................................................................................................3
Front of M30..........................................................................................................................................................................4
Display...................................................................................................................................................................................5
Connection panel...................................................................................................................................................................6
Detailed description /Connection panel...................................................................................................................................7
IR Link........................................................................................................................................................................................7
Network ....................................................................................................................................................................................7
Trigger IN...................................................................................................................................................................................7
Trigger OUT ...............................................................................................................................................................................7
USB ...................................................................................................................................................................................7
WiFi antenna.............................................................................................................................................................................7
Rack installation ........................................................................................................................................................................8
Environmental conditions in the rack .......................................................................................................................................8
Installation with wall-mounting bracket................................................................................................................................9
Integration ........................................................................................................................................................10
First steps ............................................................................................................................................................................ 10
Establishing a new WLAN connection (manually activating REVOX Connect) ......................................................................11
I/O module........................................................................................................................................................12
Installing module.................................................................................................................................................................12
Connections......................................................................................................................................................................... 13
Anschlussbeschreibung...........................................................................................................................................................13
Technical data of I/O module ..............................................................................................................................................13
Technical data M30............................................................................................................................................14

Introduction M30 Multiuser Amplifier
3
Introduction
Congratulations on acquiring your new M30 Multiuse amplifer. We would like to thank you for the trust you have shown in our
company by purchasing this high-quality product. Before commissioning your Revox M30, you should pay attention to the
following instructions in order to fully benefit from the acoustic qualities of the product.
For general safety instructions, information on how to dispose of your old devices and the warranty terms, please refer to the
enclosed leaflet.
Pay attention to the warning labels on the device and/or its external power supply unit:
In order to prevent the risk of electric shock, do not remove any coverings.
Maintenance and repairs are only to be performed by qualified specialists!
Unpacking
We recommend keeping the packaging materials in case the product needs to be transported at a later point in time.
Please check the M30 Multiuse Amplifer and its accessories after unpacking to ensure that it is complete and has not suffered
any damage during transport. Before commissioning the device, please read through the operating manual carefully. Keep it as
a reference document.
A device which has suffered mechanical damage or which liquids have penetrated into is not to be connected to the mains.
Network requirements for M30
The Multiuser amplifer is a network device and requires a network connection for operation. It can be integrated into the
network with a cable (LAN) or via a 2.4 GHz or 5 GHz WiFi interface that supports 802.11 g/n/a/ac wireless technology. You can
find more about this in the “Integration” chapter. In a multiuser system, a maximum of 7 M30 amplifiers can be wirelessly
connected to a network via WLAN. All other M30 amplifiers must then be connected by cable via LAN.
The Revox Multiuser app is available free of charge in the store for Android devices from Android 7.0 and Apple devices from
iOS 9.35.
Included in delivery
•M30 Multiuser amplifier
•WiFi antenna 2,4/ 5 GHz
•Power cable 3-pol
•Network cable
•Feet of unit (self-adhesive)
Described software version: 0.5.0 (see Display)

Introduction M30 Multiuser Amplifier
4
Front of M30
No Power
Status Display Function
1
⚫
⚫
M30 is starting
2
⚫

M30 in standby, but no network connection (status flashing)
3
⚫
⚫
M30 is switched on and connected to the network, playback is running
4
⚫
⚫
M30 in Standby
5
⚫
⚫
M30 active in the background: one or more inputs from an optional module are
in sensitive mode and/or are being streamed from other amplifiers.
6
⚫
⚫
M30 is switched on but not connected to the network or has been disconnected
from the network.
Name Function
Info display
Displays various operating data details. Called through the Setup button
Ventilation intake
Do not cover the opening - required for fresh air intake
Monitor [socket]
Headphone output - 3.5 mm, stereo jack
Power [LED]
Operational state status display
Setup [button]
For calling up various operational data in the info display
Status [LED]
System activity display

Introduction M30 Multiuser Amplifier
5
Display
The Setup button can be used to call up the various operating data.
No. Function
Explanation
1
The REVOX Connect integration routine for integration into the local WLAN is active.
Manual activation/deactivation via setup button (press 3 sec).
2
The M30 automatically receives the current firmware of the Multiuser Server. This can be,
for example, a STUDIOMASTER M300 / M500 or a V400 server. After the software package
has been downloaded, the new firmware is updated. A % display informs about the update
progress.
3
If the M30 does not receive an IP address via WLAN or LAN, it indicates this with the message
"No network". At the same time, it activates the Revox Connect interface in the background.
4
In the delivery state, the room is displayed with the corresponding MAC address of the M30.
A (0) completes the room identifier. After configuration in the Multiuser Configurator, the
display shows the assigned "Room Alias". A level display informs about the volume status of
the amplifier/power stage.
5
Like the room, the source is specified as a combination with the MAC address. A (0)
terminates the source indentifier. After configuration in the Multiuser Configurator, the
display shows the assigned "Source Alias". A level indicator informs about the input level of
the current source, if it is a local source of the optional I/O module.
Source index: CO: coaxial OP: optical AN: analogue
6
The trigger (IN/OUT) is also indicated as a combination with the MAC address. An indexing
completes the trigger identifier. After configuration in the Multiuser Configurator, the
display shows the assigned "Trigger Alias". The display shows the status of the IN or OUT
trigger in the bottom line.
7
Via the infrared display, you can read which RC5 code (address / command) was last
received. A current RC5 reception is displayed when [IR] is shown.
8
Display of the current version of the Multiuser System.
9
Display of the current version of the M30 operating system.
10
If an optional module is installed in the M30, its identity can be determined via the
displayed item number, here e.g. 1.563.080.00 of the I/O module.
11
The IP address of the M30 is displayed here, which it has obtained from the router via
DHCP.
12
Display of the pure MAC address of the M30.
13
Display of the system time of the Revox Multiuser Server.
14
At the end of the display loop, the M30 switches off if no audio input detects a signal.
Otherwise, the next time the Setup button is pressed, the room identifier is displayed again.

Connection panel M30 Multiuser Amplifier
6
Connection panel
Name
Function
AC Power
Power cable connection (class 1 with ground cable)
Please take note of the connection specifications: 100-240 VAC~ / 50-60 Hz / 140 W max.
[Retaining]
M4 threaded hole for locking the unit in place on the rack-assembly shelf or on the wall-mounted bracket.
[Blanking plate]
Opening for the installation of optional Multiuser modules, e.g. I/O module
IR Link*
Connection for Voxnet 218 wall-mounted keypad or various other Revox IR receivers.
[Ventilation outlet]
Do not cover the opening - required for expelling heated air
Network
RJ45 socket for LAN cabling in the network (100 Mbit)
R Speaker L
Speaker connection / Impedance: at least 4 
DSP correction profiles available for all Revox speakers in the Configurator
Trigger IN
Voltage trigger input: 5 - 48 VAC/VDC. Potential-free. Ri: approx. 1000 
Trigger OUT*
Voltage trigger output 12 VDC (configurable)
[Rating plate]
Unit-specific information
USB mini
USB mini socket for update (only manufacturer)
WLAN antenna
Antenna for WLAN connection. Network integration of the M30 via wireless WLAN connection or initial start-up with
the help of REVOX Connect via BLE (Bluetooth Low Energy) connection.
* Max. Gesamtstromstärke von IR-Link und Trigger OUT: 80 mA

Connection panel M30 Multiuser Amplifier
7
Detailed description /Connection panel
IR Link
Various Revox products can be connected to the IR Link:
•C18 wall remote control (I = 23mA)
•M204 IR Receiver (I = 7mA)
•M204 IR Receiver flange (I = 7mA)
•M204 IR Receiver aluminium housing (I = 7mA)
All products have one thing in common, that they send and/or forward RC5 commands to the M30.
If the M30’s Trigger OUT is not being used, devices with an overall current of up to 80 mA may be connected to the IR Link. The
individual current requirements in [mA] are listed above.
Please note that cables with small cross-sections or long cable lengths can impact both qualitatively and quantitatively on the
data signal to such an extent, that it is no longer recognised by the M30.
Max, lengths: 100 m at 0.25mm² / cable strand (AWG 23)
* Overall current
[IR-Link + Trigger Out): max. 80 mA
Network
Network connection: If the Revox Multiuser Amplifier M30 is connected to the network via cable, a multicast-capable network is
required (information on this can be found in the Multiuser Network Knowledge documentation). Minimum requirements: 100
Mbit; better 1 Gbit network, IGMP Querrier and IGMP Snooping V2 activated.
Trigger IN
Voltage-controlled input trigger (room trigger) that is given its function through the Multiuser Configurator. It can be used both
for the ON and the OFF state of different actions.
Input voltage can be between 5 and 48 volts, DC or AC. The IN trigger applies a load of approx. 1000 to the supplying source.
Trigger OUT
The output trigger supplies 12 VDC. Its function can be defined through the Configurator or by using Multiuser text. The OUT
trigger can deliver an overall current* of up to 80 mA, assuming that the IR Link is not being used.
USB
USB mini-port for installing the Multiuser M30 software (as a fallback solution) if the firmware is no longer functional.
WiFi antenna
Connect the supplied antenna here, which covers the WLAN range of 2.4 and 5 GHz. If you want to use a different antenna,
make sure that both frequencies (2.4 and 5 GHz) are supported.

Montage M30 Mulituser Amplifier
8
Rack installation
The M30 is designed for installation in a 19" rack. A shelf / tray (Revox Article no.: 1.563.090.00) is available as an accessory,
which can take two M30 amplifiers. The height of the shelf is 1 U.
The tray can be built into the rack with and without M30amplifiers. Both options are possible depending on the installation
environment.
The M30 has a recess to the left and right of the front edge which the metal lugs of the tray (upper picture / ) fit into. Locate
the amplifier, lined up with the right or the left of the tray and push it backwards until it reaches the back wall of the tray. The
amplifier is now fixed in place horizontally at the front and vertically.
Now turn your attention to the rear of the tray. Two knurled thumb screws are provided with each amplifier for fixing it into
place (lower picture / ). Screw the amplifier into place with these until they are hand-tight.
This completes the installation of the M30.
Environmental conditions in the rack
In the case of a rack installation, you must ensure that the inside temperature of the rack does not exceed +40°C / +104°F. If
necessary, the rack must be actively cooled using a fan.
The M30 amplifier itself is fitted with an active fan control and controls its own inner temperature. Cool air is sucked in at the
front of the amplifier, drawn through the unit and blown out of the slots at the back. For this reason, cool air must be able to
get to the front of the amplifier to be drawn in, even if the rack door is closed. Multiple trays can be mounted underneath each
other in the rack, without having to leave any gaps between them.
Heat dissipation M30
Typically: 13 W / 44 BTU/hr

Montage M30 Mulituser Amplifier
9
Use an inrush current limiter
When installing more than 4 pieces of M30 Multiuser Amplifiers per fused circuit (16 A), Revox recommends using an inrush
current limiter. This effectively prevents the fuse from blowing when the system is switched on again, e.g. in the event of a
power failure or night shutdown.
Installation with wall-mounting bracket
An optional wall-mounting bracket is available (Revox Article no.: 1.563.091.00), which can take one M30 amplifier. In this case,
the M30 connections are directed downwards. The front panel with the display is directed upwards.
The 4 x 30 mm pan head screws supplied are used for mounting the bracket on the wall, as shown in the assembly instructions.
Then, you can simply hang the bracket on the screws.
It is advisable to complete the cabling of the M30 before mounting it on the wall-mounted bracket as the connections are very
close to the wall.
The amplifier can now be placed on the bracket. It must be ensured that the M30 lies flush against the bracket and that its two
lugs are located in the recesses beneath the front of the M30 (lower picture / ).
Finally, the two knurled thumb screws (lower picture / ) are screwed into the amplifier's locking threads and hand-tightened.
The picture shows the positioning of the M30 (transparent) on the wall-mounted bracket (dark in the background).

Integration M30 Mulituser Amplifier
10
Integration
First steps
A network connection is required for the operation of the M30 Multiuser Amplifier in a Multiuser system. If the connection to
your own network is not wired via LAN using a network cable, you will need a mobile device (Revox C200, smartphone or tablet)
with Bluetooth and WLAN function. First of all, please download the Revox Multiuser App from the Apple App Store or the
Google Play Store and install it on your device.
You can obtain a direct link via the QR code. Simply photograph the QR code with the QR scanner of your handset and follow
the corresponding link. The link is equally valid for iOS and Android devices.
Note on the number of WLAN amplifiers
In a Multiuser system, a maximum of 7 M30 amplifiers may be wirelessly connected to a network via WLAN.
All other M30 Amplifiers must then be connected by cable via LAN.
WLAN integration into the network with Revox Connect
After switching on for the first time, the M30 display shows the following content if no network cable is connected:
The M30 is now ready to be set up via the Multiuser App. Now open the Multiuser App.
Revox Connect is a connection routine that uses Bluetooth to establish an initial connection between the M30 and your mobile
phone. Using the Multiuser App from Revox, the amplifier can now be informed of the WLAN network with its key (password)
via a Bluetooth connection.
Note: Bluetooth & location
In order to be able to use the Revox Connect function, the location function must usually also be activated on the mobile device.
Open the Multiuser
App and press the
blue Revox
Connect sign at the
bottom right.
Pressing the
Bluetooth
field starts the
search for
multiuser devices.
During the
search, the
Multiuser App
icon is shown.