RH Baby&child 1088 - 9/10 User manual

Page 1 of 12
TODDLER BED CONVERSION KIT (SOLD SEPARATELY)
KAYSE CRIB/TODDLER BED KIT – ASSEMBLY INSTRUCTIONS
Model No: 1088 - 9/10
Made in Vietnam
Distributed in the U.S.A. by:
RH Baby & Child
2900 N MACARTHUR DRIVE
TRACY, CA 95376
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
WARNING: Read all
instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Or call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools needed: key wrench (included)
Two people are recommended for assembly.
When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After bed is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool,
dry place and carefully package all original hardware to protect from loss.

Page 2 of 12
KAYSE CRIB/TODDLER BED KIT – ASSEMBLY INSTRUCTIONS
Model No: 1088 - 9/10
Never use plastic shipping bags or other plastic film as a mattress cover because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
Strangulation Hazard:
Strings can cause strangulation! DO NOT place items with a string around a child's neck, such as hood strings or
pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
To help prevent strangulation, tighten all fasteners. A child can trap parts of their body or clothing on loose fasteners.
DO NOT place the crib near a window, where cords from blinds or drapes may strangle a child.
Fall Hazard:
When child is able to pull up to a standing position, set mattress to lowest position and remove bumper pads,
large toys and other objects that could serve as steps for climbing out.
When child is able to climb out or reaches the height of 35 inches (89 cm), the crib should no longer be used, and
the child should be placed in a youth or regular bed.
Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly
and frequently during use. DO NOT use crib if any parts are missing, damaged or broken.
Contact customer service at 1-800-762-1751 for replacement parts and instructional literature if needed.
DO NOT substitute parts.
DO NOT use a water mattress with this crib.
If refinishing, use a non-toxic finish specified for children's products.
Follow warnings on all products in the crib.
Never use plastic shipping bags or other plastic film as a mattress cover because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
WARNING: Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions could result
in serious injury or death.

Page 3 of 12
KAYSE CRIB/TODDLER BED KIT – ASSEMBLY INSTRUCTIONS
Model No: 1088 - 9/10
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST
27 1/4 INCHES BY 51 5/8 INCHES WITH A THICKNESS NOT
EXCEEDING 6 INCHES.
WARNING:
Do not use this crib if the enclosed or attached instructions cannot
be strictly adhered to. Do not use this crib if the child is able to climb
out unaided or is taller than 35 inches (890 mm). Do not place
cords, straps or similar items that could become wound around the
child's neck in or near this crib. Ensure that the sides are properly
latched or locked in place when the crib is occupied. The mattress
used with this crib should not be more than 5 7/8 inches (150 mm)
thick and should be of such length and width that the gap between
the mattress and the sides of the crib does not exceed 1 3/16 inches
(30 mm) when the mattress is pushed into the corner of the crib.
Parents should inspect the crib regularly before putting the child
in the crib each day and confirm that every component of the crib
is properly and securely in place.

Page 4 of 12
KAYSE CRIB/TODDLER BED KIT – ASSEMBLY INSTRUCTIONS
Model No: 1088 - 9/10
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
The mattress intended for use on the bed must be a full-size crib mattress
having minimum dimensions of 51 5/8 inches (1310 mm) in length, 27 1/4
inches (690 mm) in width and 4 inches (100 mm) in thickness, not
exceeding 6 inches (152 mm) in thickness.
If guard rails are used as the mattress containment means, the guard rail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed, which could cause an entrapment.
DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
DO NOT place items with a string, cord, or ribbon around a child's neck,
such as hood strings or pacifier cords.
A child using the toddler or day bed must be at least 15 months of age
and weigh 50 lbs (22.7 kg) or less.
WARNING: ENTRAPMENT/STRANGULATION HAZARD

Page 5 of 12
KAYSE CRIB/TODDLER BED KIT – ASSEMBLY INSTRUCTIONS
Model No: 1088 - 9/10
PARTS INCLUDED:
A
B
C
D
HARDWARE INCLUDED:
[2]
[2]
[1]
[1]
HEADBOARD/FOOTBOARD
STATIONARY SIDE RAIL
MATTRESS SUPPORT
BASE FRAME
1
2
3
4
5
6
4 pieces
NO. ITEM DESCRIPTIONQTY.
4 pieces
6 pieces
14 pieces
1 piece
A
A
B
B
C
D
Insert Head 6mm
L Pin 6mm
Allen Key 4mm 1 piece
Allen Key 6mm
Medium Bolts 5/16" x 2"
Flat Washer 5/16" x 19 x 2mm

ASSEMBLY INSTRUCTIONS
Note: - Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the above parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten bolts until all steps are finished.
STEP 1:
Page 6 of 12
KAYSE CRIB/TODDLER BED KIT – ASSEMBLY INSTRUCTIONS
Model No: 1088 - 9/10
Attach the Headboard Panel/Footboard Panel (A)
to the Base Frame (D) by aligning wooden dowel
on the Base Frame (D) with the pre-drilled holes
on Headboard Panel/Footboard Panel (A).
Insert Medium Bolts (5) and Flat Washer (6), and
tighten with Allen Key (2).
A
A
A
A
D
D
2
5
6

Page 7 of 12
KAYSE CRIB/TODDLER BED KIT – ASSEMBLY INSTRUCTIONS
Model No: 1088 - 9/10
Highest level
Lowest level
Middle level
STEP 2:
Carefully turn the crib upright.
Insert L Pins (3) into the pre-drilled holes on the
Headboard/Footboard (A). Position the Matttress
Support (C) between the Headboard/Footboard (A).
Then align L Pin (3) into the pre-drilled holes of the
Mattress Support (C). Tighten with Insert Head (4)
and Allen Key (1).
Note: The Mattress Support (C) should be at the
highest level when the child is born. It must be at
the lowest level before the child can stand up.
Before installing the Mattress Support (C), please
ask the customer at which height they want it
installed.
A
A
A
CC
1
3
4
Top
Bottom

Page 8 of 12
KAYSE CRIB/TODDLER BED KIT – ASSEMBLY INSTRUCTIONS
Model No: 1088 - 9/10
After crib is completely assembled, return to
each bolt and tighten to a snug fit.
DO NOT overtighten.
WARNING:
STEP 3:
STEP 4:
Attach the Stationary Side Rails (B) to the
Headboard/Footboard (A) with Medium
Bolt (5), and tighten using Allen Key (2).
Position the Stationary Side Rails (B)
between the Headboard/Footboard (A)
and align the holes.
A
A
A
A
A
B
B
B
B
2
5

Page 9 of 12
KAYSE CRIB/TODDLER BED KIT – ASSEMBLY INSTRUCTIONS
Model No: 1088 - 9/10
TODDLER RAIL ASSEMBLY
1 piece
4 pieces
PARTS INCLUDED:
E [1] TODDLER RAIL
HARDWARE INCLUDED:
E
7
8
9
Medium Bolts 5/16" x 2"
NO. ITEM DESCRIPTION QTY.
Allen Key 4mm
2 pieces
Short Bolts 5/16" x 3/4"

Page 10 of 12
KAYSE CRIB/TODDLER BED KIT – ASSEMBLY INSTRUCTIONS
Model No: 1088 - 9/10
STEP 5:
Remove Stationary Side Rail (B) from the crib
by carefully unscrewing and removing the
four Medium Bolts (5) with spring washer on
Left/Right sides of the Stationary Side Rail (B)
using Allen Key (9).
A
A
A
B
B
9
5
A
A
B