RH NICCOLO User manual

NICCOLO FLOATING MIRROR 26" (66 CM) X 48" (122 CM)
ASSEMBLY AND INSTALLATION INSTRUCTIONS
ENGLISH

NICCOLO FLOATING MIRROR 26" (66 CM) X 48" (122 CM) ENGLISH
RH.COM
REVISION 24-05-22
NICCOLO FLOATING MIRROR 26" (66 CM) X
48" (122 CM)
PART LIST
(A) Mirror With Bracket (1)
(B) Steel screw (5)
(C) EZ mini anchor (5)
(D) Aluminum hanger (1)
(E) Buffer (4)
WARNING
1. In order to prevent falling down this product must be used with the
wall attachment device provided.
2. Assess the suitability of the wall to ensure that the fastening devices
will withstand the forces generated.
STORAGE
1. Do not stack anything on top of the mirror.
2. Keep the mirror packaged until installation.
3. Store mirror upright on the long edge.
MIRROR HANDLING INSTRUCTIONS
Caution:
1. Remove vertically from package.
2. Always carry mirror vertically as illustrated.
Carrying flat will cause breakage.
BEFORE YOU BEGIN
1. Professional installation recommended.
2. Tool and materials required:
Carpenter's level
Phillips head screwdriver
3. These instructions are provided for your safety. It is important that
they are read carefully and completely before installation of the
fixture.
4. For your safety, it is recommended that two people hang the fixture.
5. Check with a professional to ensure your wall can tolerate a fixture
weighing 80 lbs (36 kg).
6. When wall mounting, stud mounting is strongly recommended.
(A)
(B)
(C)
(D)
(E)

NICCOLO FLOATING MIRROR 26" (66 CM) X 48" (122 CM) ENGLISH
RH.COM
REVISION 24-05-22
INSTALLATION OF MIRROR
**NOTE: Before hanging the mirror on the wall remove the support
bars.
WALL MOUNTING
1. Unpack all parts and place them on a protected work surface.
2. Determine the exact location of the fixture and mark the holes on the
wall surface using the holes in the aluminum hanger (D) as a guide.
3. Drill small holes on each point location on the wall.
Each hole should be just large enough to accommodate EZ mini
anchor (C).
4. Insert the EZ mini anchors (C) into the holes on the wall.
5. Mount the aluminum hanger (D) into the wall using screws (B).
6. Check that the aluminum hanger fixture is securely screwed into the
wall.
7. Attached buffer (E) at 4 corners of the back mirror (A).
8. Place the mirror with hanger cleat (A) into the aluminum hanger
fixture.
9. Installation is complete.
**NOTE: MAKE SURE THAT THE TWO (2) CLEATS (1 ON MIRROR
AND 1 ON WALL) ARE LOCKED AND SECURED WITH EACH
OTHER. A LEVEL CHECK IS HIGHLY RECOMMENDED.
CHECK AND ADJUST IF NEEDED.
CLEANING INSTRUCTIONS
To clean, use a soft dry or damp cloth.
Do not use abrasive cleaners.
REMOVE THE WOOD SUPPORT
FIGURE 1
WALL MOUNTING
FIGURE 2
A
E
E
E
E
BC
Wall
Mirror
FIGURE 5
FIGURE 3
FIGURE 6
FIGURE 4
OK NOT OK
C
Wall
B
D
Plywood frame
Backside
Backside

NICCOLO FLOATING MIRROR 30" (76 CM) X 40" (102 CM)
ASSEMBLY AND INSTALLATION INSTRUCTIONS
ENGLISH

NICCOLO FLOATING MIRROR 30" (76 CM) X 40" (102 CM) ENGLISH
RH.COM
REVISION 24-05-22
NICCOLO FLOATING MIRROR 30" (76 CM) X
40" (102 CM)
PART LIST
(A) Mirror With Bracket (1)
(B) Steel screw (6)
(C) EZ mini anchor (6)
(D) Aluminum hanger (1)
(E) Buffer (4)
WARNING
1. In order to prevent falling down this product must be used with the
wall attachment device provided.
2. Assess the suitability of the wall to ensure that the fastening devices
will withstand the forces generated.
STORAGE
1. Do not stack anything on top of the mirror.
2. Keep the mirror packaged until installation.
3. Store mirror upright on the long edge.
MIRROR HANDLING INSTRUCTIONS
Caution:
1. Remove vertically from package.
2. Always carry mirror vertically as illustrated.
Carrying flat will cause breakage.
BEFORE YOU BEGIN
1. Professional installation recommended.
2. Tool and materials required:
Carpenter's level
Phillips head screwdriver
3. These instructions are provided for your safety. It is important that
they are read carefully and completely before installation of the
fixture.
4. For your safety, it is recommended that two people hang the fixture.
5. Check with a professional to ensure your wall can tolerate a fixture
weighing 50 lbs (22 kg).
6. When wall mounting, stud mounting is strongly recommended.
(A)
(B)
(C)
(D)
(E)

NICCOLO FLOATING MIRROR 30" (76 CM) X 40" (102 CM) ENGLISH
RH.COM
REVISION 24-05-22
INSTALLATION OF MIRROR
**NOTE: Before hanging the mirror on the wall remove the support
bars.
WALL MOUNTING
1. Unpack all parts and place them on a protected work surface.
2. Determine the exact location of the fixture and mark the holes on the
wall surface using the holes in the aluminum hanger (D) as a guide.
3. Drill small holes on each point location on the wall.
Each hole should be just large enough to accommodate EZ mini
anchor (C).
4. Insert the EZ mini anchors (C) into the holes on the wall.
5. Mount the aluminum hanger (D) into the wall using screws (B).
6. Check that the aluminum hanger fixture is securely screwed into the
wall.
7. Attached buffer (E) at 4 corners of the back mirror (A).
8. Place the mirror with hanger cleat (A) into the aluminum hanger
fixture.
9. Installation is complete.
**NOTE: MAKE SURE THAT THE TWO (2) CLEATS (1 ON MIRROR
AND 1 ON WALL) ARE LOCKED AND SECURED WITH EACH
OTHER. A LEVEL CHECK IS HIGHLY RECOMMENDED.
CHECK AND ADJUST IF NEEDED.
CLEANING INSTRUCTIONS
To clean, use a soft dry or damp cloth.
Do not use abrasive cleaners.
REMOVE THE WOOD SUPPORT
FIGURE 1
WALL MOUNTING
FIGURE 2
A
E
E
E
E
BC
Wall
Mirror
FIGURE 5
FIGURE 3
FIGURE 6
FIGURE 4
OK NOT OK
C
Wall
B
D
Plywood frame
Backside
Backside

NICCOLO FLOATING MIRROR 36" (92 CM) X 48" (122 CM)
ASSEMBLY AND INSTALLATION INSTRUCTIONS
ENGLISH

NICCOLO FLOATING MIRROR 36" (92 CM) X 48" (122 CM) ENGLISH
RH.COM
REVISION 24-05-22
NICCOLO FLOATING MIRROR 36" (92 CM) X
48" (122 CM)
PART LIST
(A) Mirror With Bracket (1)
(B) Steel screw (6)
(C) EZ mini anchor (6)
(D) Aluminum hanger (1)
(E) Buffer (4)
WARNING
1. In order to prevent falling down this product must be used with the
wall attachment device provided.
2. Assess the suitability of the wall to ensure that the fastening devices
will withstand the forces generated.
STORAGE
1. Do not stack anything on top of the mirror.
2. Keep the mirror packaged until installation.
3. Store mirror upright on the long edge.
MIRROR HANDLING INSTRUCTIONS
Caution:
1. Remove vertically from package.
2. Always carry mirror vertically as illustrated.
Carrying flat will cause breakage.
BEFORE YOU BEGIN
1. Professional installation recommended.
2. Tool and materials required:
Carpenter's level
Phillips head screwdriver
3. These instructions are provided for your safety. It is important that
they are read carefully and completely before installation of the
fixture.
4. For your safety, it is recommended that two people hang the fixture.
5. Check with a professional to ensure your wall can tolerate a fixture
weighing 70 lbs (31 kg).
6. When wall mounting, stud mounting is strongly recommended.
(A)
(B)
(C)
(D)
(E)

NICCOLO FLOATING MIRROR 36" (92 CM) X 48" (122 CM) ENGLISH
RH.COM
REVISION 24-05-22
INSTALLATION OF MIRROR
**NOTE: Before hanging the mirror on the wall remove the support
bars.
WALL MOUNTING
1. Unpack all parts and place them on a protected work surface.
2. Determine the exact location of the fixture and mark the holes on the
wall surface using the holes in the aluminum hanger (D) as a guide.
3. Drill small holes on each point location on the wall.
Each hole should be just large enough to accommodate EZ mini
anchor (C).
4. Insert the EZ mini anchors (C) into the holes on the wall.
5. Mount the aluminum hanger (D) into the wall using screws (B).
6. Check that the aluminum hanger fixture is securely screwed into the
wall.
7. Attached buffer (E) at 4 corners of the back mirror (A).
8. Place the mirror with hanger cleat (A) into the aluminum hanger
fixture.
9. Installation is complete.
**NOTE: MAKE SURE THAT THE TWO (2) CLEATS (1 ON MIRROR
AND 1 ON WALL) ARE LOCKED AND SECURED WITH EACH
OTHER. A LEVEL CHECK IS HIGHLY RECOMMENDED.
CHECK AND ADJUST IF NEEDED.
CLEANING INSTRUCTIONS
To clean, use a soft dry or damp cloth.
Do not use abrasive cleaners.
REMOVE THE WOOD SUPPORT
FIGURE 1
WALL MOUNTING
FIGURE 2
A
E
E
E
E
BC
Wall
Mirror
FIGURE 5
FIGURE 3
FIGURE 6
FIGURE 4
OK NOT OK
C
Wall
B
D
Plywood frame
Backside
Backside

NICCOLO FLOATING MIRROR 60" (153 CM) X 60" (153 CM)
ASSEMBLY AND INSTALLATION INSTRUCTIONS
ENGLISH

NICCOLO FLOATING MIRROR 60" (153 CM) X 60" (153 CM) ENGLISH
RH.COM
REVISION 24-05-22
NICCOLO FLOATING MIRROR 60" (153 CM) X
60" (153 CM)
PART LIST
(A) Mirror With Bracket (1)
(B) Steel screw (6)
(C) EZ mini anchor (6)
(D) Aluminum hanger (1)
(E) Buffer (4)
WARNING
1. In order to prevent falling down this product must be used with the
wall attachment device provided.
2. Assess the suitability of the wall to ensure that the fastening devices
will withstand the forces generated.
STORAGE
1. Do not stack anything on top of the mirror.
2. Keep the mirror packaged until installation.
3. Store mirror upright on the long edge.
MIRROR HANDLING INSTRUCTIONS
Caution:
1. Remove vertically from package.
2. Always carry mirror vertically as illustrated.
Carrying flat will cause breakage.
BEFORE YOU BEGIN
1. Professional installation recommended.
2. Tool and materials required:
Carpenter's level
Phillips head screwdriver
3. These instructions are provided for your safety. It is important that
they are read carefully and completely before installation of the
fixture.
4. For your safety, it is recommended that two people hang the fixture.
5. Check with a professional to ensure your wall can tolerate a fixture
weighing 145 lbs (65 kg).
6. When wall mounting, stud mounting is strongly recommended.
(A)
(B)
(C)
(D)
(E)

NICCOLO FLOATING MIRROR 60" (153 CM) X 60" (153 CM) ENGLISH
RH.COM
REVISION 24-05-22
INSTALLATION OF MIRROR
**NOTE: Before hanging the mirror on the wall remove the support
bars.
WALL MOUNTING
1. Unpack all parts and place them on a protected work surface.
2. Determine the exact location of the fixture and mark the holes on the
wall surface using the holes in the aluminum hanger (D) as a guide.
3. Drill small holes on each point location on the wall.
Each hole should be just large enough to accommodate EZ mini
anchor (C).
4. Insert the EZ mini anchors (C) into the holes on the wall.
5. Mount the aluminum hanger (D) into the wall using screws (B).
6. Check that the aluminum hanger fixture is securely screwed into the
wall.
7. Attached buffer (E) at 4 corners of the back mirror (A).
8. Place the mirror with hanger cleat (A) into the aluminum hanger
fixture.
9. Installation is complete.
**NOTE: MAKE SURE THAT THE TWO (2) CLEATS (1 ON MIRROR
AND 1 ON WALL) ARE LOCKED AND SECURED WITH EACH
OTHER. A LEVEL CHECK IS HIGHLY RECOMMENDED.
CHECK AND ADJUST IF NEEDED.
CLEANING INSTRUCTIONS
To clean, use a soft dry or damp cloth.
Do not use abrasive cleaners.
REMOVE THE WOOD SUPPORT
FIGURE 1
WALL MOUNTING
FIGURE 2
A
E
E
E
E
BC
Wall
Mirror
FIGURE 5
FIGURE 3
FIGURE 6
FIGURE 4
OK NOT OK
C
Wall
B
D
Plywood frame
Backside
Backside