Ricoh RDC-5300 User manual

Operation Manual
To ensure correct use of your digital
camera, read this manual carefully
before use. Keep the manual handy
for future reference.

Introduction
Thank you for purchasing a Ricoh digital camera. This manual explains the correct
handling procedures and precautions for your camera. To ensure the best performance,
please read the manual thoroughly before using the camera. Keep the manual handy
for quick future reference. Ricoh Co., Ltd.
Test Shots
Check that your camera is recording the images correctly by taking a number of test
shots.
Copyright
Reproduction or alteration of copyrighted documents, magazines, music and other
materials, other than for personal, home or similarly limited purposes, without the
consent of the copyright holder is prohibited.
Exemption from Liability
Ricoh Co., Ltd. assumes no liability for failure to record or play back images caused
by malfunction of the digital camera.
Warranty
This product is manufactured to local specifications and the warranty is valid within
the country of purchase. Should the product fail or malfunction while you are abroad,
the manufacturer assumes no responsibility for servicing the product locally or bearing
the expenditure incurred therefor.
Radio Interference
Operating the digital camera in the vicinity of other electronic equipment may adversely
affect the performance of both devices. In particular, operating the camera close to
a radio or television may lead to interference. If interference occurs, follow the
procedures below.
– Move the camera as far away as possible from the TV, radio or other device
– Reorient the TV or radio antenna.
– Plug the devices into separate electrical outlets.
• This publication may not be reproduced in whole or part without the express written permission of Ricoh.
©1999 Ricoh Co., Ltd. All rights reserved.
• Ricoh reserves the right to change the contents of this publication without notice. Considerable care was
taken in preparing this manual. If, however, you have questions about any part of the manual, or note
mistakes or inaccuracies, please contact us at the address listed on the back cover.
Microsoft, MS and Windows are registered trademarks of Microsoft Corporation in the United States of America
and other countries. Macintosh is a registered trademark of Apple Computer, Inc., in the United States of America
and other countries. All trademarked company and product names mentioned in this manual are the property of
their respective owners.

1
Camera Features
●2,300,000-pixel resolution compact camera
With a 2,300,000-pixel resolution CCD, the compact camera produces high-quality,
high-resolution images (1792 ×1200). The camera is so light you can carry it with you
anywhere.
● Immediate recording
Using the camera is as simple as clicking the shutter release button. Images thus shot
are written to internal memory (8 MB) or a SmartMedia memory card (2/4/8/16/32/
64 MB).
* Internal memory allow you to take pictures without the need for SmartMedia card.
● Instant playback
You can instantly review recorded image files simply by switching to Play mode. You
can also magnify the images zoom playback or display several images at once
(6-image display).
* SmartMedia memory cards let you exchange shot images with your friends.
● Multiple image recording modes
The RDC-5300 offers multiple image recording modes to suit your specific
photographic needs, including F (Fine) mode, which puts the emphasis on image
quality, N (Normal) and E (Economy) mode, which allows you to capture more images
than any other mode.
● Wide shooting range
The 3.0 ×zoom lens allows you to capture subjects in a variety of compositions, from
close-ups to shots with a background.
● Natural colors
The white balance feature allows you to capture a subject in its natural colors under
any lighting conditions, indoors or outdoors.
● Close-ups
Macro mode for taking close-up shots at distances up to 4 cm (1.6 inches) (at wide) is
ideally suited for taking flowers and small objects, etc.
● Monitors images on the TV screen
Connect the digital camera to a TV set with the video interface cable supplied and you
can display your image files on the TV screen. You can also connect the camera to a
video deck or video printer to dub the images onto a videotape or make full color
prints.
● Transfers images to a PC
You can transfer the images onto a PC using software compatible with the digital
camera. When loaded onto a PC, the images can be printed on a color printer or color
copier.

2
Table of Contents
Camera Features ................................................................................... 1
Table of Contents................................................................................... 2
Safety Precautions ................................................................................. 5
Parts & Names ..................................................................................... 10
Explanation of LCD Monitor Displays .................................................. 12
LCD Monitor ......................................................................................... 12
LCD Panel ............................................................................................ 14
Menus ................................................................................................... 17
Basic Operation/Quick Reference ....................................................... 20
Chapter 1 GETTING STARTED
Before Using the Camera ................................................................... 26
Checking the Package Contents ......................................................... 26
Attaching the Wrist Strap ..................................................................... 26
Powering the Camera ......................................................................... 27
Loading the AA Batteries ..................................................................... 27
Using an AC Adapter ........................................................................... 29
SmartMedia Memory Cards................................................................ 31
What is a SmartMedia Memory Card? ................................................ 31
Inserting a SmartMedia Memory Card................................................. 32
Formatting a SmartMedia Memory Card ............................................. 33
Before You Start Recording................................................................ 35
Setting the Date and Time ................................................................... 35
Adjusting the LCD Monitor Brightness................................................. 37
How To Hold the Camera .................................................................... 37
Chapter 2 BASIC SHOOTING
Basic Shooting .................................................................................... 40
Operation Flow ..................................................................................... 40
Turning on the Camera ........................................................................ 41
Selecting IN/CARD (Internal memory/SmartMedia memory card)
Memory................................................................................................. 42
Selecting PIC (Image quality) Mode .................................................... 43
Selecting Recording Mode................................................................... 44
Setting the Size of the Subject (Zoom)................................................ 46
How to View Images on the LCD Monitor ........................................... 47
Shooting (Still Picture Mode) ............................................................... 48

3
Chapter 3 ADVANCED SHOOTING
Changing Flash Modes....................................................................... 54
Changing the flash mode ..................................................................... 55
Setting the Exposure Compensation.................................................. 57
Setting the Exposure Compensation ................................................... 57
Changing the White Balance Mode .................................................... 59
Changing the White Balance Mode ..................................................... 59
Special Shooting Functions ................................................................ 61
Using the Self-Timer ............................................................................ 61
Focus Lock Shooting............................................................................ 62
Focus Mode Shooting .......................................................................... 63
Date Imprint Mode................................................................................ 65
Redeye Reduction Mode ..................................................................... 66
Monochrome Mode (Black & White) Sepia ......................................... 67
Interval (Time lapse) Shooting Mode................................................... 68
Using SOFT Mode ............................................................................... 70
S Mode (Shutter Speed) ...................................................................... 71
Using Auto Bracket .............................................................................. 72
Macro Shooting (Close-up Shooting) .................................................. 73
Chapter 4 PLAYBACK/ERASING
Before Starting to Playback Recorded Images .................................. 76
Playback Display .................................................................................. 76
Connecting to a TV .............................................................................. 77
Playing Back a File ............................................................................. 78
Operation Flow ..................................................................................... 78
Playing an Image File .......................................................................... 79
Multi Image Playback ........................................................................... 80
Zoom Playback..................................................................................... 81
Auto Playback ...................................................................................... 82
Protecting a File ................................................................................... 83
Copying Files........................................................................................ 84
Playing a File Shot with Another Brand of Camera............................. 86
Setting DPOF (Direct Print of File) ...................................................... 87
Setting a Printing Service .................................................................... 87
Setting Secret File................................................................................ 91

4
Erasing a File (Image) ........................................................................ 94
Operation Flow ..................................................................................... 94
Erase .................................................................................................... 95
Erase All Images .................................................................................. 96
Erase Selected Files (Images)............................................................. 97
Chapter 5 MISCELLANEOUS
Transferring Images to a PC ............................................................ 100
Changing Camera Settings............................................................... 102
Beep Sound Setting ........................................................................... 102
Auto Power Off Setting ...................................................................... 103
Keep Settings ..................................................................................... 104
Formatting Internal Memory............................................................... 105
Changing OSD (On-Screen Display) Language................................ 106
Changing Video-Out Signal Method (NTSC/PAL)............................. 107
Changing LCD Confirmation .............................................................. 108
Changing the LCD Setting ................................................................. 109
Initializing Settings ............................................................................. 110
Changing File Names......................................................................... 111
Using the DISPLAY Button to Turn the Power ON and OFF ............ 112
Checking the Version ......................................................................... 113
Using the Remote Control ................................................................ 114
Shooting ............................................................................................. 114
Playing................................................................................................ 115
Erasing ............................................................................................... 116
Accessories....................................................................................... 118
Handling Precautions........................................................................ 119
Care and Storage.............................................................................. 120
Troubleshooting ................................................................................ 121
Using Your Digital Camera in Other Countries ................................ 124
About the Warranty and Servicing.................................................... 125
Specifications.................................................................................... 127
Recording Capacities........................................................................ 129
Ricoh Service Offices ....................................................................... 131

5
RWarning
RCaution
o
m
Safety Precautions
Warning Symbols
Various symbols are used throughout this instruction manual and on the product to
prevent physical harm to you or other people and damage to property. The symbols
and their meanings are explained below.
This symbol indicates matters that may lead to death or serious
injury if ignored or incorrectly handled.
This symbol indicates matters that may lead to injury or physical
damage if ignored or incorrectly handled.
Sample Warnings
The osymbol alerts you to actions that must be performed.
The msymbol alerts you to prohibited actions.
The msymbol may be combined with other symbols to indicate
that a specific action is prohibited.
●Examples
nDo not touch qDo not disassemble
Observe the following precautions to ensure safe use of this equipment.
●Turn off the power immediately in the event of
irregularity, such as the equipment emitting smoke or a
strange smell. Remove the batteries as soon as
possible, being careful to avoid electric shocks or burns.
If you are drawing power from a household electrical
outlet, be sure to unplug the power cord from the outlet
to avoid fire or electrical hazards. Discontinue use of the
equipment immediately if it is malfunctioning. Contact
the nearest service center at your earliest convenience.
o
RWarning

6
RWarning
o●Turn off the power immediately if any metallic object,
water, liquid or other foreign object gets into the
equipment. Remove the batteries as soon as possible,
being careful to avoid electric shocks or burns. If you
are drawing power from a household electrical outlet, be
sure to unplug the power cord from the outlet to avoid
fire or electrical hazards. Discontinue use of the
equipment immediately if it is malfunctioning. Contact
the nearest service center at your earliest convenience.
●Avoid any contact with the liquid crystal inside the LCD
monitor, should the monitor be damaged. Follow the
emergency measures below in the following
circumstances.
• SKIN: If any of the liquid crystal gets on your skin, wipe
it off and rinse the affected area thoroughly with water,
then wash well with soap.
• EYES: If it gets in your eyes, wash your eyes with
clean water for at least 15 minutes and seek medical
advice immediately.
• INGESTION: If any of the liquid crystal is ingested,
rinse the mouth out thoroughly with water. Have the
victim drink a large amount of water and induce
vomiting. Seek medical assistance immediately.
●Follow these precautions to prevent the batteries from
leaking, overheating, igniting or exploding.
• Do not use batteries other than those specifically
recommended for the equipment.
• Do not put the batteries in a fire, short-circuit the
terminals, or attempt to disassemble, heat or recharge
them. (Only nickel-cadmium (Ni-Cd) and nickel-metal-
hydride (Ni-MH) batteries are rechargeable).
• Do not use a mix of battery types. Avoid mixing
different styles or classifications, batteries by different
manufacturers, or old batteries with new.
• Check that the batteries are loaded with the positive (+)
and negative (–) terminals correctly oriented.
• Do not solder the batteries.
●Do not mix rechargeable battery types or use batteries
with substantially different charge statuses.
o
m
m

7
RWarning
●Keep the batteries used in this equipment out of the
reach of children to prevent accidental ingestion of
harmful substances. Consumption of battery fluid is
extremely harmful to human beings. If swallowed, seek
immediate medical assistance.
Never use batteries in the following condition as this could
lead to leaks, overheating, ignition, explosions or short
circuits.
●Do not use batteries with insulation missing from around
the negative (–) terminal.
●Do not use batteries with outer casings that are
damaged or missing.
●Keep the equipment out of the reach of children. Their
inability to read and understand warnings and safety
precautions may lead to accidents.
●Do not touch the internal components of the equipment if
they become exposed as a result of being dropped or
damaged. The high-voltage circuitry in the equipment
could lead to an electric shock. Remove the batteries as
soon as possible, being careful to avoid electric shocks
or burns. Take the equipment to your nearest dealer or
service center if it is damaged.
●Do not attempt to disassemble, repair or alter the
equipment yourself. The high-voltage circuitry in the
equipment poses significant electrical hazard.
●Do not use the equipment in the bathroom or shower as
this could result in fire or electric shock.
m
Negative (–) Terminal
Positive (+) Terminal
Never use batteries with insulation
missing in these areas.
Outer Casing
o
m
n
q

8
RWarning
m●Do not use the equipment near flammable gases,
gasoline, benzine, thinner or similar substances to avoid
the risk of explosion, fire or burns.
●Do not use the equipment in aircraft or other locations
where usage is restricted or prohibited as this may lead
to disasters or accidents.
●Wipe off any dust that accumulates on the electrical plug
as this may lead to fire.
●Use only the specified AC adapters for this equipment
(optional AC-3) in household electrical outlets. Other
adapters pose the risk of fire, electric shock or injury.
●To avoid the risk of fire, electric shock or injury, do not
use the AC adapter with commercially available
electronic transformers when traveling abroad.
o
m

9
Observe the following precautions to ensure safe use of this unit.
RCaution
●Contact with fluid leaking from a battery can lead to
burns. If part of your body comes in contact with a
damaged battery, wash the area with water immediately.
(Do not use soap.) If a battery starts to leak, remove it
immediately from the equipment and wipe the battery
chamber thoroughly before replacing it with a new
battery.
●Plug the power cords securely into the electrical outlets.
Loose cords pose a fire hazard.
●Do not allow the camera to get wet. In addition, do not
operate it with wet hands. Both pose the risk of electric
shock.
●Do not fire the flash at drivers of vehicles, such as
bicycles, cars and trains, as this may cause the driver to
lose control and result in a traffic accident.
●Do not grasp batteries with metallic tweezers as this may
form a short circuit and lead to fire or electric shock.
Safety Warnings for Accessories
•Safety warnings for the optional accessories, such as the AC adapter, are contained
in the instruction manual provided with each product and should be read thoroughly
before operating the equipment.
o
m
m
m
o

10
Parts & Names
■Camera Body
Front
POWER Switch
(p.41)
Flash LED (p.61)
AF Indication LED (p.48)
Zoom button (p.46)
ENTER button
MENU button
DISPLAY button
Back
RS-232C/AUX Terminal
(USB cable can be connected)
Video Output Terminal (p.77)
Power Supply Terminal
(DC Input) (p.30)
Reset Button
Card Door (p.32)
Viewfinder
Flash (p.55)
Lens
Flash Sensor Reception Window
Remote Control Reception
Self Timer LED
(p.61)
Mode Dial (p.41)
LCD panel
PIC (Image quality) button (p.43)
Self Timer button (p.61)
Flash Mode button (p.55)
CARD/IN button (p.42)
Shutter Release
button (p.48)
Terminal
Cover
LCD Monitor
Video Input/
Output switch

11
Battery Cover (p.28)
Brightness Adjustment
Dial (for the LCD
monitor) (p.37)
Tripod Screw Hole
Wrist Strap Eyelet (p.26)
Contact Surface
Label Position
Write Protect Area
RELEASE
ERASE FWD PROGRAM
EV
MULTI REV
ENTER
DR-3
REMOTE CONTROLLER
MADE IN JAPAN
Bottom
■AC Adapter (optional)
•AC-3 (100V-240V)
■SmartMedia ■Remote Control Unit
Memory Card (optional) (optional) (DR-3)
Connection Cable
Power Cord
External Flash
Synchro Socket

12
Date & Time Display (p.35)
Zoom Indication Bar (p.46)
PIC (Image quality) Mode
(p.43)
• 1800 ×1200/900 ×600
Fine Mode [F]
• 1800 ×1200/900 ×600
Normal Mode [N]
• 1800 ×1200/900 ×600
Economy Mode [E]
Battery Symbol (p.13, 29)
Recording Data Indicator
Displays the remaining
number of pictures.
Focus (p.62)
AF•MF•SP
Recording Mode (p.44)
• Quick shooting mode ( )
• Still Picture Mode ( )
• Text Mode ( )
Exposure
compensation level
Recording Data
No. of the image file
displayed.
Total no. of files recorded.
Source for playback (p.76, 79)
• Internal memory ( )
• SmartMedia ( )Folder name/File name
(xxx-000)
xxx: Folder name in wich
pictures are recorded.
0000: File name of a picture
Shooting Date and Time
Explanation of LCD Monitor Displays
The LCD monitor or the LCD panel displays symbols and figures showing the status of
your digital camera, such as the battery level, the number of pictures that can be
taken, and the mode settings.
LCD Monitor
■ Recording Mode Displays
Redeye reduction mode
(p.66)
White Balance Indicator (p.59)
• Auto (no symbol)
• Daylight Mode [ ]
• Cloudy Mode (Overcast Mode) ( )
• Tungsten Light mode ( )
• Fluorescent Light Mode ( )
IN/CARD (internal card) memory (p.42)
• Internal memory ( )
• SmartMedia ( )
Message Display
Self-Timer Mode (p.61)
■ Play Mode Displays
Image Protect Mark (p.83)
Secret mark ( ) (p.91)
Battery symbol
PIC (Image quality) Mode
(p.79)
• 1800 ×1200/900 ×600
Fine Mode [F]
• 1800 ×1200/900 ×600
Normal Mode [N]
• 1800 ×1200/900 ×600
Economy Mode [E]
Flash Mode (p.55)
• Flash Off Mode ( )
• Forced Flash Mode ( )
• Slow Synchro Mode ( : flashing)
• Auto Flash Mode ( )
100-0045
1800x1200 N
1999/05/15 10:12
18/19
MF AB 1800x1200 N
T
W
EV+0.5 1999/05/15 10:12
12
SET
DATE/TIME
Auto Bracket (p.72)

13
•All items of information are shown for illustration purposes. During actual
camera operation, only the relevant items are displayed.
■Warning Messages
If any of the warning messages listed below appears on the camera’s LCD monitor,
read the corresponding explanation and take the corrective action suggested.
Note
Warning
Message Status Explanation and Remedy Reference
Page
Lit
Flashing
Flashing
Flashing
Flashing
Lit
Flashing
Flashing
Flashing
Indicates low batteries. Have
replacement batteries ready.
A SmartMedia memory card is out of
position. Mount a SmartMedia
memory card.
A write-protected SmartMedia memory
card is found. Remove the write
protection label from the card to gain
access to it.
The file you are attempting to erase is
a secret file. Do not attempt to erase
secret files.
You attempted to erase a protected
file. Unprotect the file before erasing
it.
There are no files to play. Mount a
SmartMedia memory card having files
recorded on it.
You attempted to play an unplayable
file.
No more files can be recorded.
Format the internal memory or insert a
new SmartMedia memory card to
continue recording. (Displayed when
the file name becomes Rxxx 9999
during setting the sequential File No.)
The date has not been set. Set the
date before starting operations with
the camera.
P. 27
P. 32
P. 31
P. 91
P. 83
P. 32
P. 76
P. 32, 105
P. 35
NO CARD
WRITE
PROTECTED
SECRET
FILE
FILE
PROTECTED
NO IMAGE
UNMATCHED
FILE
FILE
NUMBER
OVER
SET
DATE/TIME

14
■ Error Messages
If any of the error messages listed below appears on the camera’s LCD monitor, read
the corresponding explanation and take the corrective action suggested.
Error message
Error
Message Explanation and Remedy Reference
Page
The SmartMedia memory card is
unformatted. Format the card with the
camera before using it.
Format the internal memory before using it.
A SmartMedia memory card of this type is
not supported by this camera.
Slide the power switch to turn the power off
and then on again.
P. 33
P. 105
–
FORMAT CARD
FORMAT
INTERNAL
MEMORY
CARD ERROR
ERROR
XX-XX-XX-XX-XX
If the error display does not clear, reset the LCD monitor to its factory default:
How to reset: With the terminal cover open, press the reset button (p. 10). If
the error display still won’t clear, call your dealer or our service contact.
LCD Panel
■Initial display (SETUP mode)
Note
The LCD panel appears
blank.
FORMAT
INTERNAL
MEMORY
–

15
■Displays Appearing during Recording
Battery Symbol (p.12, 29) Recording Data Indicator
Displays the available picture
count.
PIC Mode (p.43)
•1800/900
Fine Mode (F)
•1800/900
Normal Mode (N)
•1800/900
Economy Mode (E)
Self-Timer (p.61)
Redeye Reduction Mode (p.66)
Built-in Flash (p.55)
•Flash Off ( )
•Forced Flash ( )
•Slow Synchro ( : flashing)
•Auto Flash (no mark appearing)
Recording Destination
(p.42)
•Internal memory ( )
•SmartMedia memory card
( )
Note
•The recording information indicator uses the letter L to designate the 100s
place in the remaining number of files when it is 1,000 or more.
•In shooting with the digital zoom function enabled, only F, N or E is displayed
as a PIC mode.
■Displays Appearing during Playback/Erasure
Battery Symbol (p.12, 29) PIC Mode (p.43)
•1800/900
Fine Mode (F)
•1800/900
Normal Mode (N)
•1800/900
Economy Mode (E)
Source for Playback
(p.76, 79)
•Internal memory ( )
•SmartMedia memory card
( )
Note
•Either CARD or IN is displayed for files recorded on any other digital camera,
such as a digital camera from the RDC-300/RDC-4000 Family (Ricoh) or
one of non-Ricoh make.
•The PIC mode is not displayed when the multi-image playback or erase
function is enabled.
■Displays Appearing during Communication (Communication
Mode)
• On an RS-232C cable connection
Battery Symbol (p.12, 29) The LCD monitor displays the
message “WAITING.”
Recording Destination
(p.42)
•Internal memory ( )
•SmartMedia memory card
( )
• On a USB cable connection
Battery Symbol (p.12, 29) The LCD monitor displays
nothing.

16
■Error Displays and Contents
When one of the following errors appears on the LCD panel on top of the camera
body, check the contents and take appropriate action.
Slide the power switch on the camera body
to turn the power source being used
(battery, AC adapter) off and then on again.
If a battery is being used, replace the
battery with a new one.
Note
•If the error display does not clear, reset the LCD monitor to its factory default:
How to reset:With the terminal cover open, press the reset button (P.10). If
the error display still won’t clear, call your dealer or our service contact.
Reference pageContentsError display
E-0
E-1
E-2
E-3
E-4
E-5
–

17
Menus
This camera features four menus which can be used to enter or change the settings
for recording, playing or erasing image files.
■ SET UP Menu
With the camera turned on, set the mode dial to [SET UP]. To cancel the setup menu,
turn the mode dial to select another mode.
FORMAT: ................... Formats internal memory or a
SmartMedia memory card.
(p.33, 105)
DATE SETTING: ........ Sets the date and time. (p.35)
KEEP SETTINGS:...... Saves camera settings. (p.104)
BEEP SOUND:........... Switches the electronic beep on
and off. (p.102)
AUTO POWER
OFF:............................ Enables or disables the auto
power-off feature, whereby the
camera switches off
automatically when left idle for
about 5 minutes or longer.
(p.103)
LANGUAGE: .............. Switches the LCD monitor
display between Japanese and
English. (p.106)
VIDEO OUT MODE:... Switches the camera between
NTSC and PAL when it is
connected to a TV set. (p.107)
VERSION: .................. Displays current version
information about the camera.
(p.113)
LCD
CONFIRMATION: ...... Sets the confirmation time for
images after shooting. (p.108)
LCD SETTING: .......... Selects whether to let the
camera come up with the LCD
monitor enabled or disabled
when it is powered on in a
recording mode. (p.109)
INITIALIZE
SETTING: ................... Initialize all the settings. (p.110)
PASSWORD: ............. Sets a password for the secret
function. (p.91)
SEQUENTIAL FILE NO. :... Sets a sequential file NO. or not.
(p.111)
DISPLAY →POWER : ... Sets whether to turn the power
on/off by pressing the DISPLAY
button. (p.112)
MENU SET UP]
FORMAT
DATE SETTING :1999/1/1
KEEP SETTINGS
BEEP SOUND :ON
AUTO POWER OFF :1 MIN
LANGUAGE :ENGLISH
VIDEO OUT MODE :NTSC
VERSION
SEL.:ENTER
MENU SET UP]
LCD CONFIRMATION : 1SEC
LCD SETTING : ON
INITIALIZE SETTING
PASSWORD : OFF
SEQUENTIAL FILE NO:ON
DISPLAY POWER :OFF
SEL.:ENTER

18
RECORDING
MODE: ........................ Switches between recording
modes, such as text, quick
shooting and still picture (p.44).
WHITE BALANCE: .... Switches between the white
balance settings (p.59).
+/–(Exposure
compensation):......... Sets the exposure compensation
(p.57).
FOCUS: ...................... Switches between auto focus
and manual focus (p.63).
DATE IMPRINT:......... Records images with date. (p.65)
REDEYE REDUCTION:
.................................... Reduces the red-eye when
shooting live subjects with flash.
(p.66)
MONOCHROME: ....... Records images in Black &
White or sepia. (p.67)
INTERVAL MODE:..... Switches interval (time lapse)
setting on and off (p.68).
SOFT MODE: ............. Smooths the contours of the
image. (p. 70)
S MODE: .................... Sets the shutter speed to a faster
setting for shooting in dim light
(p.71).
AUTO BRACKET:...... Three frames are exposed: one
frame at the current exposure
compensation value, one at -
0.5EV and another at +0.5EV.
(p. 72)
■ Record Menu
With the camera turned on, set the mode dial to [ ] and press the menu button. To
exit the record menu, press the menu button again.
MENU RECORD]
RECORDING MODE :
WHITE BALANCE :AUTO
+/– :OFF
FOCUS :AUTO
DATE IMPRINT :OFF
REDEYE REDUCTION:OFF
MONOCHROME :OFF
INTERVAL MODE :OFF
BACK:MENU SEL.:ENTER
MENU RECORD]
SOFT MODE :OFF
S MODE :OFF
AUTO BRACKET :OFF
BACK:MENU SEL.:ENTER