Ricoh DDP 70e User manual

Installation
Manual
© 2005 Ricoh Printing Systems, Ltd.
March, 2007
N90411

Revision Table for manual
Rev. for
Manual
Machine
Rev. Page No.(Contents) Date
00 - First dition May, 23. ’05
01 - Table of Contents ii(01) 2-3(01), 2-4(01), 2-5(01),
4-4(01), 4-15(01), 5-1(01), 5-2(00) to 5-7(00)
Oct, 21. ’05
02 U5 RoHS Compliance. 2-4(02),2-5(02),2-7(01) to 2-10(01),2-16(01)
3-2(01),3-4(01),3-9(01) to 3-11(01),3-15(01),4-5(01),4-7(01),
4-10(01) to 4-12(01),4-19(01),4-21(01) to 4-23(01),4-25(01),
4-27(01) to 4-29(01),4-32(01) to 4-35(01),
Mar, 24. ‘06
03 - 2-4(03),2-5(03) Mar, 5. ‘07
04 - 5-8(00) Jan,22.’08
05 - Table of Contents i(01),ii(02),1-1(01),1-2(01) ,4-1(01), 4-37(02),
Added pages : 2-17(00),2-18(00),2-19(00),3-16(00) ,
4-5(00),4-14(00),4-15(00),4-16(00),4-17(00),4-18(00),4-19(00),
4-20(00),4-44(00),4-45(00),4-46(00),4-47(00),
4-48(00),4-49(00),4-50(00), 4-51(00),Appendix9(00),
Appendix10(00),Appendix11(00), Appendix12(00)
Mar,28.’08
06 - 2-17(01),4-17(01),4-18(01) Apl, 10.’08
07 - 2-17(02),2-18(01) ,4-17(02),4-18(02), 4-48(01),4-49(01) Jun, 18.’08

© 2005 Ricoh Printing Systems, Ltd. All rights reserved.
No part of this document may be reproduced without the expressed permission of Ricoh Printing
Systems, Ltd.
The material in this document is for informational purposes and is subject to change without notice.
Ricoh Printing Systems, Ltd. assumes no responsibility for errors or omissions in this document. No
liability is assumed for any damages resulting from the use of the information it contains.
This manual describes information for handling and operating the DDP184 laser printer.
NOTICE TO USER
In an effort to meet the demands of a rapidly changing technology, the manufacturer is continually
developing new features and functions to meet your changing printing or printer needs. As a result,
this manual may not exactly reflect future changes made to the product. Please be sure to consult
all manual updates or addenda when using this product’s documentation.
INTRODUCTION
This manual provides essential information to install the DDP70 laser printer.
Carefully read and understand the safety instructions in this manual before starting installation.
Keep this manual on hand for reference.
DDP70 represent the model LB070B### laser printer.
(#:0-9, A-Z or blank).

BLANK

Table of Contents i
II L 01
Table of Contents
SAFETY SUMMARY
1. General Safety Guidelines …………………………………………………………………. Safety-1
2. Hazard Warning Statements ……………………………………………………………… Safety-2
2.1 WARNING Statement …………………………………………………………………. Safety-2
CHAPTER 1. INSTALLATION REQUIREMENTS ........................................1-1
1.1 A PPLICATION ......................................................................................................................1-1
1.2 I
NSTALLATION A R A ...........................................................................................................1-1
1.3 I
NSTALLATION U NIT ............................................................................................................1-1
1.4 T
OOLS R QUIR D .............................................................................................................1-2
1.5
NVIRONM NTAL C ONDITIONS ...........................................................................................1-2
1.6 I
NPUT L IN V OLTAG .........................................................................................................1-2
CHAPTER 2. UNPACKING ............................................................................2-1
2.1 U NPACKING OF TH NGIN ...............................................................................................2-1
2.1.1 Components in the package................................................................................................ 2-1
2.1.2 Unpacking Procedures ........................................................................................................ 2-2
2.1.3 Parts Check in the Accessory Box ...................................................................................... 2-4
2.2 U NPACKING OF TH F INISH R ............................................................................................2-6
2.2.1 Components in the package................................................................................................ 2-6
2.2.2 Unpacking Procedures ........................................................................................................ 2-7
2.2.3 Parts Check in the Accessory Box ...................................................................................... 2-9
2.3 U NPACKING OF TH H IGH C APACITY H OPP R ..................................................................2-11
2.3.1 Confirmation of Parts Quantities.........................................................................................2-11
2.3.2 Unpacking Procedures .......................................................................................................2-11
2.4 U NPACKING OF TH C ONTAIN R S TACK R 1 OR 2............................................................2-13
2.4.1 Confirmation of Parts Quantities........................................................................................ 2-13
2.4.2 Unpacking Procedures ...................................................................................................... 2-14
2.4.3 Parts Check in the Accessory Box .................................................................................... 2-16
2.5 U NPACKING OF TH T RANSIT P ASS U NIT T YP DDP .......................................................2-17
2.5.1 Confirmation of Parts Quantities........................................................................................ 2-17
2.5.2 Confirmation of the Accessories Parts .............................................................................. 2-17
2.5.3 Unpacking Procedures ...................................................................................................... 2-18
2.6 U NPACKING OF TH F INISH R SR5000............................................................................2-19
2.6.1 Confirmation of Parts Quantities........................................................................................ 2-19
2.6.2 Unpacking Procedures ...................................................................................................... 2-19
CHAPTER 3. PREPARATION FOR INSTALLATION...................................3-1
3.1 P R PARATION FOR I NSTALLATION OF TH P RINT R .............................................................3-1

Table of Contents ii
II L 02
3.1.1 Removing the Protection Tape and Mat from the ngine.................................................. 3-1
3.1.2 Set the PS Air Filter for the ngine Rear Cover.................................................................. 3-2
3.1.3 Removing the Protection Tape from 2000 Sheet Hopper.................................................. 3-3
3.1.4 Removing the Protection Tape from 500 Sheet Hopper ; 2 portion................................ 3-3
3.2 P R PARATION FOR I NSTALLATION OF TH F INISH R ............................................................3-4
3.3 P
R PARATION FOR I NSTALLATION OF TH H IGH C APACITY H OPP R ..................................3-12
3.4 P
R PARATION FOR INSTALLATION OF TH C ONTAIN R S TACK R 1 OR 2............................3-14
3.5 P
R PARATION FOR INSTALLATION OF TH T RANSIT P ASS U NIT T YP DDP ......................3-16
CHAPTER 4. INSTALLATION.........................................................................4-1
4.1 I NSTALLATION IN TH COMPOSITION OF TH P RINT R AND F INISH R / F INISH R SR5000 ...4-1
4.2 I
NSTALLATION IN TH COMPOSITION WITH TH H IGH C APACITY H OPP R ...........................4-21
4.3 I
NSTALLATION IN TH COMPOSITION WITH TH C ONTAIN R S TACK R 1 OR 2.....................4-24
4.3.1 Connection of the ngine and Container Stacker 1 or 2.................................................. 4-24
4.3.2 Connection of the Container Stacker 1 and Container Stacker 2 .................................... 4-32
4.3.3 Connection of the Container Stacker 2 and Finisher / Finisher SR5000......................... 4-37
CHAPTER 5. CHECKS...................................................................................5-1
5.1 C ONFIRMATION OF TH PAP R SIZ INDICATION ..................................................................5-1
5.2 P
RINTING OF TH STATUS R PORTS ...................................................................................5-4
5.3 C
H CK TH PRINT CONTAMINATION ....................................................................................5-5
5.4 C
ONFIRMATION OF TH STAPLING .......................................................................................5-5
5.5 A
DJUSTM NT OF PAP R F DING POSITION OF T RAY 1.......................................................5-6
APPENDIX 1. INSTALLATION AREA INFORMATION....................................1
APPENDIX 2. LOCATIONS OF THE LEVELING BOLT AND CASTER ......10

SAFET SUMMAR
Safety 1
II L 00
The hazard warnings which appear on the warning labels on the machine or in the manual have one of
the following alert headings consisting of an alert symbol and a signal word, DANG R, WARINIG, or
CAUTION.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANG R: Indicates an imminently hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING: Indicated a potentially hazardous situation which, if not avoided, can result
in death or serious injury.
CAUTION: Indicates a hazardous situation which, if not avoided, will or can result in
minor or moderate injury, or serious damage of product.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result
in property damage.
1. General Safety Guidelines
Before operating the machine, read the following instructions carefully:
• Follow all the installation procedures provided in this manual.
• Pay special attention to and follow all the hazard warnings on the machine and in the manual.
Failure to do so can cause injury to yourself or damage to the machine.
• Do not perform any installation in any way other than as provided in this manual.
• Keep in mind that the hazard warnings in this manual or on the machine cannot cover every
possible case, as it is impossible to predict and evaluate all circumstances beforehand. Be alert
and use your common sense.

SAFET SUMMAR (Continued)
Safety 2
II L 00
2. Hazard Warning Statements
The following are the hazard warning statements contained in this manual.
2.1 WARNING Statement
• Leave over than 400mm at the rear of the Printer for ventilation. Otherwise print quality may be
degraded.
(Section 1.2,Page 1-1)
• Be careful when unpacking using the crane or forklift. Do not to drop device, hit it
against something, or turn it over on its side.
(Section 2.1,Page 2-1)
(Section 2.2,Page 2-6)
(Section 2.4,Page 2-11)
• Perform unpacking where there is no dust or water leaking.
(Section 2.1,Page 2-1)
(Section 2.2,Page 2-6)
(Section 2.3,Page 2-9)
(Section 2.4,Page 2-11)
(Section 2.5,Page 2-15)
• Do not place heavy objects which weigh 5 kg or more on device.
(Section 2.1,Page 2-1)
(Section 2.2,Page 2-6)
(Section 2.3,Page 2-9)
(Section 2.4,Page 2-11)
• Be careful when lifting device with the forklift so device is well-balanced on the arms of
the lift. Also put the packing (cushion) between device and the forklift so device is not
damaged.
(Section 2.1,Page 2-1)
(Section 2.2,Page 2-6)
(Section 2.4,Page 2-11)

SAFET SUMMAR (Continued)
Safety 3
II L 00
• Observe the speed limit of 300 mm/sec. (1.08 km/hr) when moving device. Do not
move device on unleveled floor. Do not tilt device 15 ° or more.
(Section 2.1,Page 2-1)
(Section 2.2,Page 2-6)
(Section 2.3,Page 2-9)
(Section 2.4,Page 2-11)
• Choose the location to place device where the slope is less than 15 °. (Only left and right
direction from view of operator’s side.)
(Section 2.1,Page 2-1)
(Section 2.2,Page 2-6)
(Section 2.3,Page 2-9)
• Choose the location to place device where there is no condensation.
(Section 2.1,Page 2-1)
(Section 2.2,Page 2-6)
(Section 2.3,Page 2-9)
(Section 2.4,Page 2-11)
• Choose the location to place device where the slope is less than 15 °.
(Section 2.4,Page 2-11)
• The voltage is constantly in unless the machine is unplugged or Breaker Switch is turned off.
(Section 4.1,Page 4-3)
• Unplug the Power Supply Cable prior to connecting the power supply source.
(Section 4.1,Page 4-3)
• Be careful not to have other personnel plug in the power cable while performing the connecting.
(Section 4.1,Page 4-3)
(Section 4.1,Page 4-4)

SAFET SUMMAR (Continued)
Safety 4
II L 00
• Unplug the Power Supply Cable prior to connecting.
(Section 4.1,Page 4-4)
• Be careful not to have other personnel plug in the power cable while performing the connecting.
(Section 4.1,Page 4-4)
• Be sure to use power supply cable which complies with the following specification :
Power plug rating ; Min. AC 250V, Min. 15A (2-Pole, 3-Wire, Grounded)
6-15P UL Listed, CSA Certified in North America
Type CA, Conformed to I C 950 in urope
Power cable rating ; Min. AC 250V, Min. 15A
Type SJT or SVT, UL Listed, CSA Certified in North America
Conformed to I C 950 in urope
(Section 4.1,Page 4-4)
• Use the Power Supply Cable which is approximately 50 mm longer for the FG. The cable should be
designed as below, so the FG power cable remains connected if the other cables are accidentally
disconnected.
(Section 4.1,Page 4-4)
• Make sure that the power cables are connected to the correct terminals (“L”, “N” ) on the power plug
and Terminal Block. ( FG power cable is connected to chassis.)
(Section 4.1,Page 4-4)
• The socket-outlet shall be installed near the printer and be easily accessible.
(Section 4.1,Page 4-4)

Installation Requirements 1-1
II L 00
Chapter 1. Installation Requirements
1.1 Application
This specification is applied to the DDP70 Printer for Unpacking, Installing and Adjustment.
1.2 Installation Area
Installation area is shown in Appendix 1.1–1.12 corresponding to Table 1.1.
Table 1.1 Installation area
Appendix Printer Finisher
Transit Pass
Unit Type
DDP
Finisher
SR5000
High Capacity
Hopper
Container
Stacker 1
Container
Stacker 2
1.1 X X
1.2 X X X
1.3 X X
1.4 X X X
1.5 X X X
1.6 X X X X
1.7 X X X
1.8 X X X X
1.9 X X X
1.10 X X X X
1.11 X X X X
1.12 X X X X X
X: Composed
Leave over than 400mm at the rear of the Printer for ventilation. Otherwise
print quality may be degraded.
1.3 Installation Unit
Locations of the leveling bolt and Caster is shown in Appendix 2.1–2.4.
WARNING
II L 01

Installation Requirements 1-2
II L 00
1.4 Tools Required
Table 1.2 Tools Required
Item Name Usage
1 Cutter Unpacking
2 Phillips Screw Driver NO.2 shaft
length; approx. 40 and 100mm
Removing and installing the screw for covers
3 Adjustable Open nd Wrench Leveling the bolt
Fixing the leveling the bolts
4 Level Meter Installation the Container Stacker
1.5 Environmental Conditions
Table 1.3 nvironmental Conditions
Items Value
Temperature 10 ~32 °C (50 ~ 89.6°F)
Humidity 20 ~80 %RH
(Wet Bulb 26 °C (78.8 °F ) max.)
Altitude 0 to 2,100 m (0 to 7,000 feet) max.
1.6 Input Line Voltage
Table 1.4 Print ngine Input Line Voltage
Input Line Voltage AC 200V ~ AC 240V
Phase Single Phase, two wires and grounding wire
Frequency 50/60 Hz ±1Hz
Transient (Static) ±10%
Transient (Dynamic) –18% / +15% 500ms
Drop out -100%, 20ms
II L 01

Unpacking 2-1
II L 00
Chapter 2. Unpacking
2.1 Unpacking of the Engine
1) Be careful when unpacking using the crane or forklift. Do not to drop
device, hit it against something, or turn it over on its side.
2) Perform unpacking where there is no dust or water leaking.
3) Do not place heavy objects which weigh 5 kg or more on device.
4) Be careful when lifting device with the forklift so device is well-balanced
on the arms of the lift. Also put the packing (cushion) between device
and forklift so device is not damaged.
5) Observe the speed limit of 300 mm/sec. (1.08 km/hr) when moving
device. Do not move device on unleveled floor. Do not tilt device 15 ° or
more.
6) Choose the location to place device where the slope is less than 15 °.
(Only left and right direction from view of operator’s side.)
7) Choose the location to place device where there is no condensation.
2.1.1 Components in the package
Table 2.1 Components in the package
Unit of Packing Quantity
ngine 1
Accessory Box 1
WARNING

Unpacking 2-2
II L 00
2.1.2 Unpacking Procedures
1) Cut the V Bands and remove the Cap.
2) Remove the screws.
3) Remove the Packing, Accessory box, Ramps, Upper Packing.
4) Remove the Box, Corner Packing.
Ramp
Box
Packing
Accessory Box
Screw
Upper Packing
Corner Packing
Corner Packing
Base Packing
Under Tray
Flat Pallet
Cap

Unpacking 2-3
II L 00
5) Jack up the ngine by rotating the leveling bolts.
Put the wood spacer (It is taken out from the accessories box.) under four leveling bolts.
Jack up the ngine by rotating the leveling bolts.
6) Remove the Base Packing.
7) Place all Casters in the same direction.
8) Lower the ngine on the Under Tray and screw the leveling bolts in all the way.
9) Attach the four Ramps under the Platform.
10) Carefully roll the ngine off the Tray.
Ramp
Platform
Caster
Down
Up
Leveling Bolt
II L 01

Unpacking 2-4
II L 00
2.1.3 Parts Check in the Accessory Box
II L 03
Developer Bottle
Toner(Black)
User’s Guide Installation Manual
Wire Cleaning Tool
Interlock Stopper
Maintenance Panel Ass’y
CD-ROM
(Documentation)
Special Tool
Cable Clamp
Screws
CD-ROM
(S/W & Manual)
CD-ROM
(Driver / JT)
Software License
Agreement
Wood Spacer
PS Air Filter
Notes For Users

Unpacking 2-5
II L 00
Table 2.2 Parts list in the Accessory Box
No. Parts Name Qty Use
1 US R’S GUID 1 For Customer
2 D V LOP R BOTTL 1 For Developer exhaust
3 MAINT NANC PAN L ASSY 1 For Customer ngineer
4 WIR CL ANING TOOL 1 For Customer ngineer
5 INT RLOCK STOPP R 1 For Customer ngineer
6 TON R(BLACK) 1 For Customer
7 INSTALLATION MANUAL 1 For Customer ngineer
8SOFTWAR LIC NS
AGR M NT 1 For Customer
9 CD-ROM (DOCUM NTATION) 1 For ngineer
10 CD-ROM (DRIV R / JT) 1 For ngineer
11 WOOD SPAC R 4 For Customer ngineer
12 PS AIR FILT R 1 For Customer ngineer
13 NOT S FOR US RS 1 For Customer
II L 03

Unpacking 2-6
II L 00
2.2 Unpacking of the Finisher
1) Be careful when unpacking using the crane or forklift. Do not to drop
device, hit it against something, or turn it over on its side.
2) Perform unpacking where there is no dust or water leaking.
3) Do not place heavy objects which weigh 5 kg or more on device.
4) Be careful when lifting device with the forklift so device is well-balanced
on the arms of the lift. Also put the packing (cushion) between device
and forklift so device is not damaged.
5) Observe the speed limit of 300 mm/sec. (1.08 km/hr) when moving
device. Do not move device on unleveled floor. Do not tilt device 15 ° or
more.
6) Choose the location to place device where the slope is less than 15 °.
(Only left and right direction from view of operator’s side.)
7) Choose the location to place device where there is no condensation.
2.2.1 Components in the package
Table 2.3 Components in the package
Unit of Packing Quantity
Finisher 1
Accessory Box 1
WARNING

Unpacking 2-7
II L 00
2.2.2 Unpacking Procedures
[FS-104H] (No RoHS Compliance Unit)
1) Cut the V Bands and remove the Outside Box.
2) Remove the two Upper packing, Accessory Box.
3) Remove the Tape of Protection Bag and take down the Protection Bag.
4) Carefully lift the Finisher by two persons and stand on Floor.
II L 01