RIDGID 1215 User manual

1215 Threading
Machine
•Français– 17
• Castellano – 35
Threading Machine Manual

1215 Threading Machines
999-997-051.10_REV B
ii
Table of Contents
Recording Form for Machine Serial Number................................................................................................................................... 1
Safety Symbols..................................................................................................................................................................................2
General Power Tool Safety Warnings*..............................................................................................................................................2
Work Area Safety..........................................................................................................................................................................2
Electrical Safety............................................................................................................................................................................2
Personal Safety ............................................................................................................................................................................3
Power Tool Use and Care .............................................................................................................................................................3
Service .........................................................................................................................................................................................4
Specific Safety Information ..............................................................................................................................................................4
Threading Machine Safety Warnings............................................................................................................................................4
RIDGID Contact Information.............................................................................................................................................................4
Description.........................................................................................................................................................................................4
Specifications ....................................................................................................................................................................................5
Standard Equipment.....................................................................................................................................................................5
Machine Assembly.............................................................................................................................................................................6
Mounting on Stands .....................................................................................................................................................................6
Mounting on Bench ......................................................................................................................................................................6
Pre-Operation Inspection.................................................................................................................................................................. 6
Machine and Work Area Set-Up........................................................................................................................................................ 6
Die Head Set-Up and Use..................................................................................................................................................................8
Removing/Installing Die Head ......................................................................................................................................................8
Quick-Opening Die Heads............................................................................................................................................................8
Operating Instructions ......................................................................................................................................................................9
Cutting with No. 732 Cutter......................................................................................................................................................... 10
Reaming with No. 344 Reamer................................................................................................................................................... 10
Threading Pipe........................................................................................................................................................................... 11
Threading Bar Stock / Bolt Threading......................................................................................................................................... 11
Removing Pipe from the Machine .............................................................................................................................................. 11
Inspecting Threads..................................................................................................................................................................... 12
Preparing Machine for Transport ................................................................................................................................................ 12
Machine Storage.............................................................................................................................................................................. 12
Maintenance Instructions ............................................................................................................................................................... 13
Cleaning ..................................................................................................................................................................................... 13
Lubrication.................................................................................................................................................................................. 13
Oil System Maintenance............................................................................................................................................................. 13
Replacing No. 732 Cutter Wheel................................................................................................................................................. 13
Replacing Jaw Inserts ................................................................................................................................................................ 13
Replacing Carbon Brushes ........................................................................................................................................................ 14
Troubleshooting .......................................................................................................................................................................... 14
Service and Repair..................................................................................................................................................................... 15
Optional Equipment ........................................................................................................................................................................ 15
Thread Cutting Oil Information....................................................................................................................................................... 16
Disposal............................................................................................................................................................................................ 16
EC Declaration ........................................................................................................................................................ Inside Back Cover
Lifetime Warranty...............................................................................................................................................................Back Cover
*Original Instructions - English

1215 Threading Machines
1215 Threading Machine
Threading Machine Manual
WARNING!
Read this Operator’s Manu-
al carefully before using this
tool. Failure to understand
and follow the contents of
this manual may result in
electrical shock, re and/or
serious personal injury.
1215
1215 Threading Machines
Record Serial Number below and retain product serial number which is located on nameplate.
Serial
No.

1215 Threading Machines
999-997-051.10_REV B
2
This symbol indicates the risk of fingers, hands, clothes and other objects catching on or between gears or other rotating parts
and causing crushing injuries.
This symbol indicates the risk of fingers, legs, clothes and other objects catching and/or wrapping on rotating shafts causing
crushing or striking injuries.
General Power Tool Safety
Warnings*
WARNING
Read all safety warnings, instructions, illustrations
and specications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, re and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE!
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work Area Safety
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and by-standers away while opera-
ting a power. Distractions can cause you to lose
control.
Electrical Safety
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adap-
ter plugs with earthed (grounded) power tools.
Safety Symbols
In this operator’s manual and on the product, safety symbols and signal words are used to communicate important safety
information. This section is provided to improve understanding of these signal words and symbols.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE indicates information that relates to the protection of property.
This symbol means read the operator’s manual carefully before using the equipment.The operator’s manual contains important
information on the safe and proper operation of the equipment.
This symbol means always wear safety glasses with side shields or goggles when handling or using this equipment to reduce
the risk of eye injury.
NOTICE
DANGER
WARNING
CAUTION
This symbol indicates the risk of electrical shock.
This symbol indicates the risk of machine tipping, causing striking or crushing injuries.
This symbol means do not wear gloves while operating this machine to reduce the risk of entanglement.
This symbol means always use a foot switch when using a threading machine/power drive to reduce the risk of injury.
This symbol means do not disconnect foot switch to reduce the risk of injury.
This symbol means do not block foot switch (lock in ON position) to reduce the risk of injury.
* The text used in the General Safety Rule section of this manual is verbatim, as required, from the applicable UL/CSA 62841-1 edition standard. This section
contains general safety practices for many different types of power tools. Not every precaution applies to every tool, and some do not apply to this tool.

1215 Threading Machines
999-997-051.10_REV B 3
3
Unmodified plugs and matching outlets will reduce
risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electrical
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electrical shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is un-
avoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the
risk of electric shock.
Personal Safety
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol, or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the OFF-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energizing power tools that have the switch
ON invites accidents.
• Remove any adjusting key or wrench before turn-
ing the power tool ON. A wrench or a key left at-
tached to a rotating part of the power tool may result
in personal injury.
• Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the
power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, and clothing away from
moving parts. Loose clothes, jewelry, or long hair
can be caught in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
Power Tool Use and Care
• Do not force power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it is designed.
• Do not use power tool if the switch does not
turn it ON and OFF. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/
or the battery pack, if detachable, from the power
tool before making any adjustments, changing ac-
cessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power
tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
tool. Power tools are dangerous in the hands of
untrained users.
• Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking
into account the working conditions and the
work to be performed. The use of the power tool for
operations different from those intended could result
in a hazardous situation.

1215 Threading Machines
999-997-051.10_REV B
4
of the machine. This practice could lead to trapping,
entanglement and loss of control.
• Do not operate the machine without all covers
properly installed. Exposing moving parts increases
the probability of entanglement.
• Do not use this machine if the foot switch is
broken or missing. The foot switch provides safe
control of the machine, such as emergency shutoff in
case of entanglement.
• One person must control the work process, ma-
chine operation and foot switch. Only the operator
should be in the work area when the machine is
running. This helps reduce the risk of injury.
• Never reach into the machine front chuck or rear
centering head. This will reduce the risk of entangle-
ment.
• Read and understand these instructions and the
instructions and warnings for all equipment and
materials being used before operating this tool to
reduce the risk of serious personal injury.
RIDGID Contact Information
If you have any question concerning this RIDGID®product:
– Contact your local RIDGID®distributor.
– Visit RIDGID.com to find your local RIDGID contact
point.
– Contact Ridge Tool Technical Service Department at
ProToolsT[email protected], or in the U.S.
and Canada call 844-789-8665.
Description
The RIDGID®Model 1215 Threading Machine is an elec-
tric-motor driven machine that centers and chucks pipe,
conduit and bolt stock and rotates it while cutting, reaming
and threading operations are performed.
Threading dies are mounted in a variety of available die
heads. An integral oiling system is provided to flood the
work with thread cutting oil during the threading operation.
With proper optional equipment, the 1215 Threading
Machine can be used to thread short or close nipples.
Service
• Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
Specic Safety Information
WARNING
This section contains important safety information
that is specic to these tools.
Read these precautions carefully before using
the 1215 Threading Machine to reduce the risk of
electrical shock or other serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE!
Keep this manual with machine for use by the operator.
Threading Machine Safety Warnings
• Keep floor dry and free of slippery materials such
as oil. Slippery floors invite accidents.
• Restrict access or barricade the area when work
piece extends beyond machine to provide a mini-
mum of one meter clearance from the work piece.
Restricting access or barricading the work area around
the work piece will reduce the risk of entanglement.
• Do not wear gloves. Gloves may be entangled by
the rotating pipe or machine parts leading to personal
injury.
• Do not use for other purposes such as drilling
holes or turning winches. Other uses or modifying
this machine for other applications may increase the
risk of serious injury.
• Secure machine to bench or stand. Support long
heavy pipe with pipe supports. This practice will
prevent the machine from tipping.
• While operating the machine, stand on the side
where the operator controls are located. Operating
the machine from this side eliminates need to reach
over the machine.
• Keep hands away from rotating pipe and fittings.
Stop the machine before wiping pipe threads or
screwing on fittings. Allow the machine to come
to a complete stop before touching the pipe. This
practice will reduce the chance of entanglement in
rotating parts.
• Do not use this machine to install or remove
(make or break) fittings, it is not an intended use

1215 Threading Machines
999-997-051.10_REV B 5
Figure 1A – 1215 Threading Machine (Front)
Figure 1B – 1215 Threading Machine (Back)
Specications
Threading Capacity ........Pipe 1/4" to 1 1/2"
(6 to 37 mm)
Bolt 5/16" to 1" (8 to 25 mm)
Right Hand Threads Only
Motor:
Type.................................Universal, Single Phase
Power ..............................1/2 HP (0.37 kW)
Volts.................................120 V, 50/60 Hz
No Load Speed Ƞo..........44 RPM
Controls...........................Rocker Type ON/OFF (I/O)
Switch and ON/OFF Foot
switch
Front Chuck.....................Hammer-Type with Replaceable
Rocker-Action Jaw Inserts
Rear Centering Device ...Cam Action
5
Serial Number
Plate
Drip Tray
Cord Wrap
Carrying
Handle
Die Heads...................... See RIDGID Catalog for Avail-
able Die Heads
Cutter............................. Model 732, Roll Type Cut-Off,
Self-Centering Cutter
Reamer ...........................Model 344, Five Fluted Type
Oil System.......................1.5 qt (1,4 l) Reservoir Capacity,
Self-Priming, Gerotor Pump,
Adjustable Flow Rate
Dimensions.....................23” x 17.5” x 18” (584mm x
444mm x 457mm) (With Tools
In Operating Position and Cutter
Fully Closed)
Weight.............................80 lbs. (36 kg)
Sound Power
(LWA)*...............................82.1 dB(A)
* Sound measurements are obtained in accordance with CSA Z107.2-1973 and
OSHA 1926.52
- Sound emissions may vary due to your location and specific use of these tools.
- Daily exposure levels for sound need to be evaluated for each application and
appropriate safety measures taken when needed. Evaluation of exposure levels
should consider the time a tool is switched off and not in use. This may signifi-
cantly reduce the exposure level over the total working period.
Standard Equipment
Refer to the RIDGID catalog for details on accessories
supplied with specific machine catalog numbers.
The RIDGID Model 1215 Threading Machine serial num-
ber plate is located opposite the switch plate below the
foot switch cord wrap. The last 4 digits indicate the month
and year of the manufacture. (mm = month, yy = year).
Figure 2 – Machine Serial Number
Selection of appropriate materials and instal-
lation, joining and forming methods is the responsibility
of the system designer and/or installer. Selection of im-
proper materials and methods could cause system failure.
Stainless steel and other corrosion resistant materials can
be contaminated during installation, joining and forming.
This contamination could cause corrosion and premature
failure. Careful evaluation of materials and methods for
the specific service conditions, including chemical and
temperature, should be completed before any installation
is attempted.
XXXXXXXXMMYY
On/Off
Switch
Rear
Centering
Device
Chuck
Handwheel
Foot
Switch
Die Head No. 732
Cutter
No. 323
Reamer
Carrying
Handle
Carriage
Handwheel
Warning
Label
NOTICE
Chip Tray

1215 Threading Machines
999-997-051.10_REV B
6
and correct any problems to reduce the risk of
serious injury from electric shock, crushing injuries
and other causes, and to help prevent threading
machine damage.
1. Make sure that the threading machine is unplugged
and the ON/OFF (I/O) switch is in OFF (O) position.
2. Clean any oil, grease or dirt from the threading ma-
chine, including the handles and controls. This aids
inspection and helps prevent the machine or control
from slipping from your grip. Clean and maintain the
machine per the maintenance instructions.
3. Inspect the threading machine for the following:
• Condition of the cords and plug for damage or
modification.
• Proper assembly, maintenance and completeness.
• Any broken, worn, missing, misaligned or binding
parts or other damage.
• Presence and operation of the foot switch. Confirm
that foot switch is attached, in good condition, that it
cycles smoothly and does not stick.
• Presence and readability of warning labels (Figure 1).
• Condition of the dies, cutter wheel and reamer cut-
ting edges. Dull or damaged cutting tools increase
required force, produce poor results and increase
the risk of injury.
• Any other condition which may prevent safe and
normal operation.
If any problems are found, do not use the threading
machine until the problems have been repaired.
4. Inspect and maintain any other equipment being
used per its instructions to make sure it is functioning
properly.
Machine and Work Area Set-Up
WARNING
Set up the 1215 Threading Machine and work area
according to these procedures to reduce the risk
of injury from electric shock, machine tipping,
entanglement, crushing and other causes, and to
help prevent machine damage.
Secure the machine to a stable stand or a bench.
Properly support pipe. This will reduce the risk of
falling pipe, tipping and serious injury.
Do not use the 1215 Threading Machine without a
properly operating foot switch. A foot switch pro-
Machine Assembly
WARNING
To reduce the risk of serious injury during use,
follow these procedures for proper assembly.
Failure to mount the threading machine to a stable
stand or bench may result in tipping and serious
injury.
ON/OFF (I/O) switch should be OFF (O) and machine
unplugged before assembly.
Mounting on Stands
The 1215 Threading Machine can be mounted on
RIDGID 1203 Leg Stand. Refer to the Stand Instruction
Sheet for mounting instructions.
Mounting on Bench
The 1215 Threading Machine can be mounted on a level,
stable bench. To mount the unit on a bench, use three
3/8" bolts in holes provided on the machine base. See
Figure 3 for hole spacing.
Figure 3 – Hole spacing for mounting the 1215
Pre-Operation Inspection
WARNING
Before each use, inspect your threading machine
16.04"
10.93"
10.82"

1215 Threading Machines
999-997-051.10_REV B 7
7
create a minimum of 3' (1 m) clearance around the
threading machine and pipe. This helps prevent
non-operators from contacting the machine or pipe
and reduces the risk of tipping or entanglement.
10. Position the foot switch as shown in Figure 10 to allow
a proper operating position.
11. Check the level of RIDGID Thread Cutting Oil. Re-
move the oil pan liner and chip tray; see that the
filter screen assembly is fully submerged in oil. See
Oil System Maintenance. Make sure the drip tray is
properly placed to direct oil dripping off the die head
into the base assembly
12. With the ON/OFF (I/O) switch in OFF (O) position,
run the cord along a clear path. With dry hands, plug
the power cord into the properly grounded outlet.
Keep all connections dry and off the ground. If the
power cord is not long enough use an extension cord
that:
• Is in good condition.
• Has a three-prong plug like on the threading
machine.
• Is rated for outdoor use and contains a W or W-A in
the cord designation (e.g. SOW).
• Has sufficient wire size. For extension cords up to
50' (15.2 m) long use 14 AWG (2.5 mm2) or heavier.
For extension cords 50'-100' (15.2 m - 30.5 m) long
use 12 AWG (4.0 mm2) or heavier.
13. Check the threading machine for proper operation.
With hands clear:
• Move the ON/OFF (I/O) switch to the ON (I) position.
Press and release the foot switch. Chuck should
rotate counter-clockwise when viewed from the car-
riage end (see Figure 14). If the threading machine
does not rotate in the correct direction, or the foot
switch does not control the machine operation, do
not use the machine until it has been repaired.
• Depress and hold the foot switch. Inspect the mov-
ing parts for misalignment, binding, odd noises or
any other unusual conditions. Remove foot from
the foot switch. If any unusual conditions are found,
do not use the machine until it has been repaired.
• Place die head in the use position. Depress and
hold the foot switch. Check for oil flow through the
die head. Remove foot from the foot switch. The
oil flow can be adjusted with the control valve on
carriage (Figure 4). Clockwise rotation decreases
flow and counterclockwise increases flow. Do not
adjust while the machine is running. If needed, see
“Maintenance Instructions” section for oil system
maintenance.
vides better control by letting you shut off the
machine motor by removing your foot.
1. Check work area for:
• Adequate lighting.
• Flammable liquids, vapors or dust that may ignite.
If present, do not work in area until source is identi-
fied, removed or corrected, and area is completely
ventilated. The threading machine is not explosion
proof and can cause sparks.
• Clear, level, stable, dry location for all equipment
and operator.
• Good ventilation. Do not use extensively in small,
enclosed areas.
• Properly grounded electrical outlet of the correct
voltage. Check the machine serial plate for required
voltage. A three-prong or GFCI outlet may not be
properly grounded. If in doubt, have outlet inspected
by a licensed electrician.
2. Inspect the pipe to be threaded and associated fit-
tings and confirm that the 1215 Threading Machine
is correct tool for the job, see Specifications. Do not
use to thread anything other than straight stock. Do
not thread pipe with fittings or other attachments.This
increases the risk of entanglement.
3. Transport equipment to work area. See Preparing
Machine for Transport for information.
4. Confirm equipment to be used has been properly
inspected and assembled.
5. Confirm that the ON/OFF (I/O) switch is in the OFF
(O) position.
6. Check that the correct dies are in the die head and are
properly set. If needed, install and/or adjust the dies in
the die head. See Die Head Set-Up and Use section
for details.
7. Swing the cutter, reamer and die head up away from
the operator. Make sure they are stable and will not
fall in the work area.
8 If pipe will extend past the chip tray in the front of the
machine or more than 2' (0.6 m) out of the rear of the
machine, use pipe stands to support the pipe and
prevent the pipe and threading machine from tipping
or falling. Place the pipe stands in line with machine
chucks, approximately 1/3 of distance from end of
the pipe to the machine. Longer pipe may need more
than one pipe stand. Only use pipe stands designed
for this purpose. Improper pipe supports or supporting
the pipe by hand can cause tipping or entanglement
injuries.
9. Restrict access or set-up guards or barricades to

1215 Threading Machines
999-997-051.10_REV B
8
Figure 4 – Adjusting Oil Flow
14. Move the ON/OFF (I/O) switch to the OFF (O) posi-
tion, and with dry hands unplug the machine.
Die Head Set-Up and Use
The 1215 Threading Machine can be used with a vari-
ety of RIDGID Die Heads to cut pipe and bolt threads.
Information is included here for Quick-Opening Die
Heads. See the RIDGID catalog for other available die
heads.
Die Heads require one set of dies for each of the follow-
ing pipe size ranges: (1/4"and 3/8"), (1/2" and 3/4") and
(1" through 2"). NPT/NPSM dies must be used in NPT
Die Heads and BSPT/BSPP dies must be used n BSPT
Die Heads – The size bar is marked for each.
Die heads using Mono or Bolt dies require a dedicated
set of dies for each specific thread size.
See the RIDGID catalog for dies available for your die
head.
Always cut a test thread to confirm proper thread size
after changing/adjusting the dies.
Removing/Installing Die Head
Insert/remove Die Head Post into mating hole in carriage.
When fully inserted, the Die Head will be held in place.
When it is installed, the Die Head can be pivoted on post
to align it with pipe or it can be swung up and out of the
way to allow use of cutter or reamer.
Quick-Opening Die Heads
Quick-Opening Die Heads include Model 811A and
531/532 Bolt. Quick opening die heads are manually
opened and closed for user specified thread length. See
Figure 5.
Figure 5 –Quick-Opening Die Head
Inserting/Changing the Dies
1. Place the die head with numbers facing up.
2. Move throwout lever to OPEN position (Figure 6).
Figure 6 – Open/Closed Lever Position
3. Loosen clamp lever (Hex nut on Mono die heads)
approximately three turns.
4. Lift tongue of washer out of slot in size bar. Move
washer to end of slot (Figure 5).
5. Remove dies from
the die head.
6. Insert appropriate
dies into the die head,
numbered edge up
until the indicator line
is flush with the edge
of the die head (see
Figure 7). Numbers
on the dies must cor-
respond with those
on the die head slots.Always change dies as sets – do
not mix dies from different sets.
7. Move link index mark to align with desired size mark
Indicator
Line
Indicator
Line
Throwout
Lever Throwout
Lever
Open Closed
Figure 7 – Inserting Dies
+
-
Decrease
in flow
Increase
in Flow
Oil Flow
Control
Valve
Throwout Lever
Size Bar
Washer Tongue Link Clamp Lever (Hex
Nut on Mono Dies)
Post
Dies
Hole for Locking Pin (LH Die Heads)

1215 Threading Machines
999-997-051.10_REV B 9
on size bar. Adjust die insertion as needed to allow
movement. Washer tongue should be in slot to left.
8. Tighten clamp lever (Hex nut on Mono die heads).
Adjusting Thread Size
1. Install the die head and move the die head into
threading position.
2. Loosen clamp lever (Hex nut on Mono die heads).
3. Start with link index mark aligned with desired size
mark on size bar. On Mono and Bolt die heads, set
link mark at line in size bar. For bolt threads with
Universal die head, set all bolt dies at BOLT line on
size bar (Figure 8).
4. If thread size needs to be
adjusted, set the link index
mark slightly off the mark
on size bar in the direction
of OVER (larger diameter
thread, less turns of fitting
engagement) or UNDER
(smaller thread diameter,
more turns of fitting engage-
ment) markings.
5. Tighten clamp lever.
Opening the Die Head at the End of the Thread
At the end of the thread:
• Pipe Threads – End of threaded pipe is flush with
the end of the number 1 die.
• Bolt Threads – Thread the desired length – watch
closely for any interference between the parts.
Move the throwout lever to the OPEN position, retract-
ing dies.
Operating Instructions
WARNING
Do not wear gloves or loose clothing. Keep sleeves
and jackets buttoned. Loose clothing can become
entangled in rotating parts and cause crushing and
striking injuries.
Keep hands away from rotating pipe and parts. Stop
the machine before wiping threads or screwing on
ttings. Do not reach across the machine or pipe.
To prevent entanglement, crushing or striking
injuries, allow machine to come to a complete stop
before touching the pipe or machine chucks.
9
Figure 8 – Adjusting
Thread Size
Size Bar
“Over”
Link
Index
Mark
“Under”
Do not use this machine to make or break (tighten
or loosen) ttings. This can cause striking or crush-
ing injuries.
Do not use a threading machine without a properly
operating foot switch. Never block a foot switch
in the ON position so that it does not control the
threading machine. A foot switch provides better
control by letting you shut off the machine motor by
removing your foot. If entanglement should occur
and power is maintained to the motor, you will be
pulled into the machine. This machine has high
torque and can cause clothing to bind around your
arm or other body parts with enough force to crush
or break bones or cause striking or other injuries.
One person must control both the work process and
the foot switch. Do not operate with more than one
person. In case of entanglement, the operator must
be in control of the foot switch.
Follow operating instructions to reduce the risk of
injury from entanglement, striking, crushing and
other causes.
1. Make sure that machine and work area is properly set
up and that the work area is free of bystanders and
other distractions. The operator should be the only
person in the area while the machine is operated.
The cutter, reamer and die head should be up away
from the operator, do not place in the operating
position. Make sure they are stable and will not fall.
Fully open the chucks of the threading machine.
2. Insert pipe shorter than 2' (0,6 m) from the front of the
machine. Insert longer pipes through either end so
that the longer section extends out beyond the rear
of the Threading Machine. Confirm that pipe stands
are properly placed.
3. If needed, mark the pipe. Place pipe so that the
area to be cut or end to be reamed or threaded is
approximately 4" (100 mm) from the front of the chuck.
If closer, the carriage may strike the machine during
the threading and damage the machine.
4. Turn the rear centering device counterclockwise
(viewed from rear of machine) to close down onto
pipe. Make sure that the pipe is centered in the inserts.
This improves pipe support and gives better results.
5. Turn the front chuck handwheel counterclockwise
(viewed from front of machine) to close down onto pipe.
Make sure that the pipe is centered in the jaws. Use
repeated and forceful counterclockwise spins of the
handwheel to secure the pipe in front chuck (Figure 9).

1215 Threading Machines
999-997-051.10_REV B
10
Figure 9 – Chucking Pipe
6. Assume a proper operating position to help maintain
control of the machine and pipe (See Figure 10).
• Stand on the ON/OFF (I/O) switch side of the ma-
chine with convenient access to the tools and switch.
• Be sure that you can control the foot switch. Do not
step on foot switch yet.
• Be sure that you have good balance and do not
have to overreach.
Figure 10 – Operating Position
Cutting with the No. 732 Cutter
1. Open cutter by turning the feed screw counterclock-
wise. Lower the cutter into cutting position over the
pipe. Use the carriage handwheel to move the cutter
over the area to be cut, and align the cutter wheel with
the mark on the pipe. Cutting threaded or damaged
sections of pipe can damage the cutter wheel.
2. Tighten the cutter feed screw handle to bring the cutter
wheel firmly in contact with the pipe while keeping the
cutter wheel aligned with the mark on the pipe.
3. Move the ON/OFF (I/O) switch to the ON (I) position.
4. With both hands, grasp the pipe cutter feed screw
handle (Figure 11).
5. Depress the foot switch.
6. Tighten the feed screw handle one-half turn per rota-
tion of the pipe until the pipe is cut. More aggressive
tightening of the handle reduces cutter wheel life and
increases pipe burr formation. Do not support the pipe
by hand. Let the cut off piece be supported by the
threading machine carriage and pipe stand.
Figure 11 – Cutting with 732 Cutter
7. Remove foot from the foot switch.
8. Move the ON/OFF (I/O) switch to the OFF (O) position.
9. Raise cutter into position up away from operator.
Reaming with No. 344 Reamer
1. Move the reamer into reaming position. Make sure
that it is securely positioned to prevent it from moving
during use.
2. Move the ON/OFF (I/O) switch to the ON (I) position.
3. With both hands, grasp the carriage handwheel. See
Figure 12.
4. Depress the foot switch.
Direction of Rotation
Close
Open

1215 Threading Machines
999-997-051.10_REV B 11
Figure 12 – Reaming with 344 Reamer
5. Turn carriage handwheel to move the reamer to the
end of pipe. Apply slight pressure to the handwheel
to feed the reamer into pipe to remove the burr as
desired.
6. Remove foot from the foot switch.
7. Move the ON/OFF (I/O) switch to the OFF (O) position.
8. Move the reamer up away from the operator.
Threading Pipe
Due to differing pipe characteristics, a test thread should
always be performed before the first thread of the day or
when changing pipe size, schedule or material.
1. Lower the die head into the threading position. Con-
firm that the dies are correct for the pipe being
threaded and properly set. See the“Die Head Set-Up
and Use” section for information on changing and
adjusting dies.
2. Close the die head.
3. Move the ON/OFF (I/O) switch to the ON (I) position.
4. With both hands, grasp the carriage handwheel. See
Figure 13.
5. Depress the foot switch.
6. Confirm cutting oil flow through the die head.
7. Turn carriage handwheel to move the die head to the
end of the pipe. Apply slight force to the handwheel
to start the die head onto the pipe. Once the die head
starts threading the pipe, no more force is required on
the carriage handwheel.
8. Keep your hands away from the rotating pipe. Make
sure the carriage does not hit the machine. When the
thread is complete, open the die head.
9. Remove foot from the foot switch.
10. Move the ON/OFF (I/O) switch to the OFF (O) posi-
tion.
11
11. Turn the carriage handwheel to move the die head
past the end of the pipe. Raise the die head into
position up away from the operator.
12. Remove the pipe from the machine and inspect the
thread. Do not use the machine to tighten or loosen
fittings on the thread.
Figure 13 –Threading Pipe
Threading Bar Stock/Bolt Threading
Bolt threading is similar to the pipe threading process.
The stock diameter should never exceed the thread major
diameter.
When cutting bolt threads, the correct dies and die
head must be used. Bolt threads may be cut as long as
needed, but make sure the carriage does not hit the ma-
chine. If long threads are required:
1. At the end of carriage travel, leave the die head
closed, remove foot from the foot switch and move the
ON/OFF (I/O) switch to the OFF (O) position.
2. Open the chuck and move the carriage and workpiece
to the end of the machine.
3. Re-chuck the rod and continue threading.
Removing Pipe from the Machine
1. With the ON/OFF (I/O) switch in the OFF (O) position
and the pipe stationary, use repeated and forceful
clockwise spins of the handwheel to loosen the pipe
in the chuck. Open the front chuck and the rear-cen-
tering device. Do not reach into chuck or centering
device.

1215 Threading Machines
999-997-051.10_REV B
12
2. Clean the chips and other debris from the chip tray.
Remove or secure all equipment and material from
the machine and stand prior to moving to prevent
falling or tipping. Clean up any oil or debris on the
floor.
3. Place the cutter, reamer and die head in the operating
position.
4. Coil up the power cord and foot switch cord and hook
in the cord wrap. Figure 15.
5. If needed, remove the machine from the stand. Use
proper lifting techniques, be aware of the machine
weight. Machine is equipped with handles at front
and rear. Use care in lifting and moving.
Figure 15 – Machine prepared forTransport
Machine Storage
The 1215 Threading Machine must be
kept indoors or well covered in rainy weather. Store the
machine in a locked area that is out of reach of children
and people unfamiliar with the machine. This machine
can cause serious injury in the hands of untrained users.
Maintenance Instructions
WARNING
Make sure that the ON/OFF (I/O) switch is in the
OFF (O) position and the machine is unplugged
before performing any maintenance or making any
adjustments.
Maintain threading machine according to these pro-
cedures to reduce the risk of injury from electrical
shock, entanglement and other causes.
2. Firmly grip the pipe and remove from the machine.
Carefully handle the pipe as the thread may still be
hot and there may be burrs or sharp edges.
Inspecting Threads
1. After removing the pipe from the machine, clean the
thread.
2. Visually inspect thread. Threads should be smooth
and complete, with good form. If issues such as
thread tearing, waviness, thin threads, or pipe out-of-
roundness are found, the thread may not seal. Refer
to the Troubleshooting Chart for help in diagnosing
these issues.
3. Inspect the size of the thread.
• The preferred method of checking thread size is
with a ring gauge. There are various styles of ring
gauges, and their usage may differ from that shown
here.
• Screw ring gauge onto the thread hand tight.
• Look at how far the pipe end extends through the
ring gage. The end of the pipe should be flush with
the side of the gauge plus or minus one turn. If
thread does not gauge properly, cut off the thread,
adjust the die head and cut another thread. Using a
thread that does not gauge properly can cause leaks.
Figure14 – Checking Thread Size
• If a ring gauge is not available to inspect thread size,
it is possible to use a new clean fitting representative
of those used on the job to gauge thread size. For 2"
and under NPT threads, the threads should be cut
to obtain 4 to 5 turns to hand tight engagement with
the fitting and for BSPT it should be 3 turns.
4. Adjust the threads according to appropriate section of
“Adjusting Thread Size”under“Die Head Set-Up and
Use”heading.
5. Test the piping system in accordance with local codes
and normal practice.
Preparing Machine for Transport
1. Make sure that the ON/OFF (I/O) switch is in the
OFF (O) position and the cord is unplugged from the
outlet.
Flush
(Basic Size) One Turn Large
(Maximum Size) One Turn Small
(Minimum Size)
Ring
Gauge
WARNING

1215 Threading Machines
999-997-051.10_REV B 13
Figure 17 – Filter Screen Assembly
Replacing No. 732 Cutter Wheel
If the cutter wheel becomes dull or broken, push cutter
wheel pin out of frame and check for wear. Replace
pin if worn, and install new Cutter Wheel (see catalog).
Lubricate pin with light lubricating oil.
Replacing Jaw Inserts
If Jaw inserts are worn out and do not grip pipe, they
need to be replaced.
1. Place punch into spring detent slot of jaw and push
down (Figure 18). Continue to push down and slowly
slide insert out of chuck jaw holder.
2. Place new insert into chuck jaw holder and with
finger, depress spring and plunger. Slowly move
insert past spring and plunger until insert fully sits in
chuck jaw holder.
Figure 18 – Replacing Jaw Inserts
Replacing Carbon Brushes
Check motor brushes every 6 months. Replace when
worn to less than 1/2".
1. Unplug the machine from power source.
2. Loosen the three motor cover screws (screws are
Cleaning
After each use, empty the threading chips from the chip
tray and wipe out any oil residue. Wipe oil off exposed
surfaces, especially areas of relative motion like the
carriage rails.
If the jaw inserts do not grip and need to be cleaned, use
a wire brush to remove any build up of pipe scale, etc.
Lubrication
On a monthly basis (or more often if needed) lubricate
all exposed moving parts (such as carriage rails, cutter
wheels, cutter feed screw, jaw inserts and pivot points)
with a light lubricating oil. Wipe any excess oil from ex-
posed surfaces.
Clean the lubrication points to remove dirt and prevent
contamination of oil (Figure 16). Fill the lubrication points
with lubricating oil. Press the ball in the lubrication point
to allow the oil to reach bearings.
Figure 16 – Lubrication Points
Oil System Maintenance
Keep oil filter screen clean for sufficient oil flow. Oil filter
screen is located in the bottom of oil reservoir. Loosen
the screw that secures filter to base, remove filter from oil
line and clean (Figure 17). Do not operate machine with
oil filter screen removed.
Replace thread cutting oil when it becomes dirty or con-
taminated. To drain the oil, position a container under
drain plug at end of reservoir and remove plug. Follow all
local laws and regulations when disposing of oil. Clean
build up from the bottom of the reservoir. Use RIDGID
Thread Cutting Oil for high quality threads and maximum
die life. Oil reservoir will hold approximately 1.5 qt (1.4 l)
of thread cutting oil.
The oil pump should self-prime if the system is clean. If it
does not, this indicates that the pump is worn and should
be serviced. Do not attempt to prime the pump.
Baffle Screen assembly
Oil Pan Liner
Filter Screen
assembly
Lubrication Points

1215 Threading Machines
999-997-051.10_REV B
14
Figure 19 – Brush Placement - Motor Cover Removed
retained – do not back all the way out) and remove
motor cover.
3. Loosen the four screws to open the end cover
(screws are retained – do not back all the way out).
4. Using a pair of pliers, pull the motor brushes straight
out. Detach the connector. (See Figure 19.)
5. Inspect the commutator for wear. If excessively worn,
have tool serviced.
6. Depress the brush into the holder and insert into the
motor housing. Inspect to make sure insulator sheets
are properly positioned between brush holder and
housing.Attach the connector.
7. Reassemble unit. Install all covers before operating
machine.
Troubleshooting
PROBLEM POSSIBLE REASONS SOLUTION
Torn Threads. Damaged, chipped or worn out dies. Replace dies.
Incorrect cutting oil. Only use RIDGID®Thread Cutting Oil.
Insufficient cutting oil. Fill oil reservoir.
Dirty or contaminated oil. Replace the RIDGID Thread Cutting Oil.
Die head not properly aligned with pipe. Clean chips, dirt or other foreign material from be-
tween die head and carriage.
Improper pipe. Recommend using with black or galvanized steel pipe.
Pipe wall too thin – use schedule 40 or heavier pipe.
Die head not properly set. Adjust die head to give proper size thread.
Carriage not moving freely on rails. Clean and lubricate carriage rails.
Out-of-round or
Crushed Threads. Die head set undersize. Adjust die head to give proper size thread.
Pipe wall thickness too thin. Use schedule 40 or heavier pipe.
Thin Threads. Dies inserted into head in wrong order. Put dies in proper position in die head.
Forcing carriage feed handle during threading. Once dies have started thread, do not force carriage
feed handle.Allow carriage to self-feed.
Die head cover plate screws are loose. Tighten screws.
No cutting oil flow. Low or no cutting oil. Fill oil reservoir.
Oil Filter Screen Plugged. Clean Screen.
Die head not in the threading (DOWN) position. Move die head to the threading position.
Connector
Insulator
Sheet
Brush

1215 Threading Machines
999-997-051.10_REV B 15
15
Troubleshooting (continuation)
PROBLEM POSSIBLE REASONS SOLUTION
Machine will not run. Motor brushes worn out. Replace brushes.
Pipe slips in jaws.
Jaw inserts loaded with debris. Clean jaw inserts with wire brush.
Jaws inserts worn out. Replace jaw inserts.
Pipe not properly centered in jaw inserts. Make sure pipe is centered in jaw inserts, use the rear
centering device.
Chuck not tight on pipe. Use repeated and forceful spins of the chuck handwheel
to tighten front chuck.
Optional Equipment
WARNING
To reduce the risk of serious injury, only use equip-
ment specically designed and recommended for
use with the 1215 Threading Machine.
Catalog
No.
Model
No. Description
58657 732 Cutter Assembly
34612 344 1/8"-2" Reamer
97075 815A 1/8" - 2" NPT, Self-Opening, RH Die Head
97065 811A 1/8" - 2" NPT, Quick-Opening, RH Die
Head
84537 816 1/8" - 3/4" Semi-Automatic Die Head
84532 817 1" - 2" Semi-Automatic Die Head
97045 531 1/4" - 1" Bolt, Quick-Opening, RH/LH Die
Head
97050 532 1 1/4" - 2" Bolt, Quick-Opening, RH/LH
Die Head
58307 – Jaw Insert Set
58302 – Jaw Insert Set (Optional for SS and Plas-
tic Coated Pipe)
61187 1203 Tripod Stand
For a complete listing of RIDGID equipment available for
the 1215Threading Machine, see the RidgeTool Catalog
online at RIDGID.com or see Contact Information.
Service And Repair
WARNING
Improper service or repair can make the machine
unsafe to operate.
The “Maintenance Instructions” will take care of most
of the service needs of this machine. Any problems not
addressed by this section should only be handled by a
RIDGID Authorized Independent Service Center. Use
only RIDGID Authorized service parts.
For information on your nearest RIDGID Authorized Inde-
pendent Service Center or any service or repair ques-
tions, see Contact Information section in this manual.

1215 Threading Machines
999-997-051.10_REV B
16
Thread Cutting Oil Information
Read and follow all instructions on the threading oil
label and Safety Data Sheet (SDS). Specific information
about RIDGID Thread Cutting Oils, including Hazard
Identification, First Aid, Fire Fighting, Accidental Release
Measures, Handling and Storage, Personal Protective
Equipment, Disposal and Transportation, is included
on the container and SDS. SDS is available at RIDGID.
com or by contacting Ridge Tool Technical Service De-
partment at 844-789-8665 in U.S. and Canada or
ProToolsT[email protected].
Disposal
Parts of the 1215 Threading Machine contain valuable
materials and can be recycled. There are companies that
specialize in recycling that may be found locally. Dispose
of the components and any waste oil in compliance with
all applicable regulations. Contact your local waste man-
agement authority for more information.
For EC Countries: Do not dispose of electri-
cal equipment with household waste!
According to the European Guideline 2012/
19/EU for Waste Electrical and Electronic
Equipment and its implementation into na-
tional legislation, electrical equipment that
is no longer usable must be collected separately and
disposed of in an environmentally correct manner.

Les fileteuses électriques
AVERTISSEMENT !
Familiarisez-vous avec ce mode d’em-
ploi avant d’utiliser l’appareil. Tout
manque de compréhension ou d’adhé-
sion aux consignes ci-après augmen-
terait les risques de choc électrique,
d’incendie et/ou de grave blessure cor-
porelle.
1215
Fileteuse électrique n° 1215
Inscrivez ci-dessous et conservez le numéro de série de l’appareil indiqué sur sa plaque signalétique.
No de
série
Fileteuses électrique
n° 1215

Fileteuses électrique n° 1215
999-997-051.10_REV B
18
Table des matières
Fiche d’enregistrement du numéro de série de l’appareil ........................................................................................................... 17
Symboles de sécurité...................................................................................................................................................................... 19
Consignes générales visant la sécurité des appareils électriques*........................................................................................... 19
Sécurité des lieux....................................................................................................................................................................... 19
Sécurité électrique......................................................................................................................................................................20
Sécurité individuelle ...................................................................................................................................................................20
Utilisation et entretien des appareils électriques........................................................................................................................20
Service après-vente ...................................................................................................................................................................21
Consignes de sécurité spécifiques................................................................................................................................................21
Sécurité de la fileteuse électrique ..............................................................................................................................................21
Coordonnées RIDGID......................................................................................................................................................................22
Description.......................................................................................................................................................................................22
Caractéristiques techniques...........................................................................................................................................................22
Equipements de base.................................................................................................................................................................23
Assemblage de l’appareil................................................................................................................................................................23
Montage sur trépied ...................................................................................................................................................................23
Montage sur établi...................................................................................................................................................................... 23
Inspection préalable........................................................................................................................................................................24
Préparation de l’appareil et des lieux ............................................................................................................................................24
Préparation et utilisation des têtes de filière ................................................................................................................................26
Retrait et installation des têtes de filière.....................................................................................................................................26
Têtes de filière à ouverture rapide ..............................................................................................................................................26
Mode d’emploi .................................................................................................................................................................................27
Utilisation du coupe-tubes n° 732...............................................................................................................................................28
Utilisation de l’alésoir n° 344 ......................................................................................................................................................29
Filetage des tuyaux ....................................................................................................................................................................29
Filetage des barres à boulon...................................................................................................................................................... 30
Retrait des tuyaux de l’appareil ..................................................................................................................................................30
Inspection des filetages..............................................................................................................................................................30
Transport de l’appareil................................................................................................................................................................30
Remisage..........................................................................................................................................................................................31
Entretien...........................................................................................................................................................................................31
Nettoyage ...................................................................................................................................................................................31
Lubrification de l’appareil............................................................................................................................................................31
Système de lubrification des tuyaux...........................................................................................................................................31
Remplacement du galet de coupe du coupe-tubes n° 732 ........................................................................................................32
Remplacement des mâchoires...................................................................................................................................................32
Remplacement des balais au carbone.......................................................................................................................................32
Dépannage.................................................................................................................................................................................33
Révisions et réparations.............................................................................................................................................................34
Accessoires .....................................................................................................................................................................................34
Huile de coupe.................................................................................................................................................................................34
Recyclage .........................................................................................................................................................................................34
Déclaration CE ...............................................................................................................................................Verso de page de garde
Garantie à vie................................................................................................................................................................Page de garde
*Texte d’origine en anglais