Riello RS 310/M BLU Quick start guide

Installation, use and maintenance instructions
20153481 (6) - 03/2022
Forced draught gas burners
Modulating operation
CODE MODEL TYPE
20152646 - 20152634 RS 310/M BLU 1138T
20152650 - 20152640
20152643 RS 410/M BLU 1135T
20152653 RS 510/M BLU 1136T
20152657 RS 610/M BLU 1137T
GB

Translation of the original instructions

1 20153481
GB
Contents
1 Declarations................................................................................................................................................................................ 3
2 Information and general warnings............................................................................................................................................ 4
2.1 Information about the instruction manual .................................................................................................................... 4
2.1.1 Introduction.................................................................................................................................................................. 4
2.1.2 General dangers.......................................................................................................................................................... 4
2.1.3 Other symbols ............................................................................................................................................................. 4
2.1.4 Delivery of the system and the instruction manual...................................................................................................... 5
2.2 Guarantee and responsibility....................................................................................................................................... 5
3 Safety and prevention................................................................................................................................................................ 6
3.1 Introduction.................................................................................................................................................................. 6
3.2 Personnel training ....................................................................................................................................................... 6
4 Technical description of the burner ......................................................................................................................................... 7
4.1 Burner designation ...................................................................................................................................................... 7
4.2 Models available.......................................................................................................................................................... 8
4.3 Burner categories - Countries of destination ............................................................................................................... 8
4.4 Technical data ............................................................................................................................................................. 8
4.5 Electrical data.............................................................................................................................................................. 9
4.6 Burner weight .............................................................................................................................................................. 9
4.7 Maximum dimensions................................................................................................................................................ 10
4.8 Firing rates ................................................................................................................................................................ 11
4.9 Test boiler.................................................................................................................................................................. 12
4.10 Burner equipment...................................................................................................................................................... 12
4.11 Burner description ..................................................................................................................................................... 13
4.12 Electrical panel description........................................................................................................................................ 14
4.13 RFGO-A22 control box.............................................................................................................................................. 15
4.14 Servomotor SQM40 .................................................................................................................................................. 16
4.15 Calibration of the thermal relay ................................................................................................................................. 17
4.16 Motor rotation ............................................................................................................................................................ 17
5 Installation ................................................................................................................................................................................ 18
5.1 Notes on safety for the installation ............................................................................................................................ 18
5.2 Handling .................................................................................................................................................................... 18
5.3 Preliminary checks .................................................................................................................................................... 18
5.4 Operating position ..................................................................................................................................................... 19
5.5 Preparing the boiler ................................................................................................................................................... 19
5.5.1 Boring the boiler plate ............................................................................................................................................... 19
5.5.2 Blast tube length........................................................................................................................................................ 19
5.6 Securing the burner to the boiler............................................................................................................................... 20
5.7 Access to head internal part...................................................................................................................................... 20
5.8 Probe-electrode position ........................................................................................................................................... 21
5.9 Gas butterfly valve..................................................................................................................................................... 21
5.10 Combustion head adjustment.................................................................................................................................... 22
5.11 Gas feeding ............................................................................................................................................................... 23
5.11.1 Gas feeding line ........................................................................................................................................................ 23
5.11.2 Gas train.................................................................................................................................................................... 24
5.11.3 Gas train installation.................................................................................................................................................. 24
5.11.4 Gas pressure............................................................................................................................................................. 25
5.12 Electrical wiring ......................................................................................................................................................... 26
5.12.1 Supply cables and external connections passage .................................................................................................... 26
6 Start-up, calibration and operation of the burner ................................................................................................................. 27
6.1 Notes on safety for the first start-up .......................................................................................................................... 27
6.2 Adjustments prior to ignition ...................................................................................................................................... 27

20153481 2
GB
Contents
6.3 Servomotor adjustment..............................................................................................................................................27
6.4 Burner start-up ...........................................................................................................................................................28
6.5 Burner ignition............................................................................................................................................................28
6.6 Air / fuel adjustment ...................................................................................................................................................28
6.6.1 Burner adjustment......................................................................................................................................................29
6.6.2 Output upon ignition...................................................................................................................................................29
6.6.3 Maximum output ........................................................................................................................................................29
6.6.4 Minimum output .........................................................................................................................................................30
6.6.5 Intermediate outputs ..................................................................................................................................................30
6.7 Pressure switch adjustment .......................................................................................................................................31
6.7.1 Air pressure switch - check CO..................................................................................................................................31
6.7.2 Maximum gas pressure switch...................................................................................................................................31
6.7.3 Minimum gas pressure switch....................................................................................................................................31
6.8 Operation sequence of the burner .............................................................................................................................32
6.8.1 Burner start-up ...........................................................................................................................................................32
6.8.2 Operation ...................................................................................................................................................................32
6.8.3 Burner flame goes out during operation.....................................................................................................................32
6.8.4 Ignition failure.............................................................................................................................................................32
6.8.5 Control box reset........................................................................................................................................................32
7 Maintenance ..............................................................................................................................................................................33
7.1 Notes on safety for the maintenance .........................................................................................................................33
7.2 Maintenance programme ...........................................................................................................................................33
7.2.1 Maintenance frequency..............................................................................................................................................33
7.2.2 Safety test - with gas feeding closed .........................................................................................................................33
7.2.3 Checking and cleaning...............................................................................................................................................33
7.2.4 Safety components ....................................................................................................................................................34
7.3 Opening the burner ....................................................................................................................................................35
7.4 Closing the burner......................................................................................................................................................35
8 LED indicator and special function.........................................................................................................................................36
8.1 Description of LED lamps ..........................................................................................................................................36
8.2 Check mode function .................................................................................................................................................36
8.3 Flame control lock-out or emergency stop condition .................................................................................................36
8.4 LED lamps: burner operating status ..........................................................................................................................37
9 Problems - Causes - Remedies signalled by LED indicators ...............................................................................................38
A Appendix - Accessories ...........................................................................................................................................................43
B Appendix - Electrical panel layout...........................................................................................................................................44

3 20153481
GB
Declarations
1 Declarations
Declaration of conformity in accordance with ISO / IEC 17050-1
Manufacturer: RIELLO S.p.A.
Address: Via Pilade Riello, 7
37045 Legnago (VR)
Product: Forced draught gas burners
Model and type: RS 310/M BLU
RS 410/M BLU
RS 510/M BLU
RS 610/M BLU
1138T
1135T
1136T
1137T
These products are in compliance with the following Technical Standards:
EN 676
EN 12100
and according to the European Directives:
GAR 2016/426/EU Gas Appliances Regulation
MD 2006/42/EC Machine Directive
LVD 2014/35/EU Low Voltage Directive
EMC 2014/30/EU Electromagnetic Compatibility
PED 2014/68/EU (only FS2) Pressure Equipment Directive
Such products are marked as follows:
CE-0085CP0166 RS 310/M BLU (Class 3 EN 676)
CE-0085CP0166 RS 410/M BLU (Class 3 EN 676)
CE-0085CP0166 RS 510/M BLU (Class 3 EN 676)
CE-0085CP0166 RS 610/M BLU (Class 3 EN 676)
The quality is guaranteed by a quality and management system certified in accordance with ISO 9001:2015.
Legnago, 03.05.2021 Research & Development Director
RIELLO S.p.A. - Burner Department
Mr. F. Maltempi
Manufacturer's Declaration
RIELLO S.p.A. declares that the following products comply with the NOx emission limits specified by German standard “1. BIm-
SchV revision 26.01.2010”.
Product Model Type Output
Forced draught gas burners RS 310/M BLU 1138T 400 - 3630 kW
RS 410/M BLU 1135T 500 - 4450 kW
RS 510/M BLU 1136T 680 - 5250 kW
RS 610/M BLU 1137T 1000 - 6250 kW
0085

20153481 4
GB
Information and general warnings
2.1 Information about the instruction manual
2.1.1 Introduction
The instruction manual supplied with the burner:
is an integral and essential part of the product and must not
be separated from it; it must therefore be kept carefully for
any necessary consultation and must accompany the burner
even if it is transferred to another owner or user, or to
another system. If the manual is lost or damaged, another
copy must be requested from the Technical Assistance Ser-
vice of the area;
is designed for use by qualified personnel;
offers important indications and instructions relating to the
installation safety, start-up, use and maintenance of the
burner.
Symbols used in the manual
In some parts of the manual you will see triangular DANGER
signs. Pay great attention to these, as they indicate a situation of
potential danger.
2.1.2 General dangers
The dangers can be of 3 levels, as indicated below.
2.1.3 Other symbols
Abbreviations used
Ch. Chapter
Fig. Figure
Page Page
Sec. Section
Tab. Table
2 Information and general warnings
DANGER
Maximum danger level!
This symbol indicates operations which, if not car-
ried out correctly, cause serious injury, death or
long-term health risks.
WARNING
This symbol indicates operations which, if not car-
ried out correctly, may cause serious injury, death
or long-term health risks.
CAUTION
This symbol indicates operations which, if not car-
ried out correctly, may cause damage to the ma-
chine and/or injury to people.
DANGER
DANGER: LIVE COMPONENTS
This symbol indicates operations which, if not car-
ried out correctly, lead to electric shocks with le-
thal consequences.
DANGER: FLAMMABLE MATERIAL
This symbol indicates the presence of flammable
materials.
DANGER: BURNING
This symbol indicates the risks of burns due to
high temperatures.
DANGER: CRUSHING OF LIMBS
This symbol indicates the presence of moving
parts: danger of crushing of limbs.
WARNING: MOVING PARTS
This symbol indicates that you must keep limbs
away from moving mechanical parts; danger of
crushing.
DANGER: EXPLOSION
This symbol signals places where an explosive at-
mosphere may be present. An explosive atmos-
phere is defined as a mixture - under atmospheric
conditions - of air and flammable substances in
the form of gases, vapours, mist or dust in which,
after ignition has occurred, combustion spreads to
the entire unburned mixture.
PERSONAL PROTECTION EQUIPMENT
These symbols indicate the equipment that must
be worn and kept by the operator for protection
against threats against safety and/or health while
at work.
OBLIGATION TO ASSEMBLE THE COVER
AND ALL THE SAFETY AND PROTECTION DE-
VICES
This symbol signals the obligation to reassemble
the cover and all the safety and protection devices
of the burner after any maintenance, cleaning or
checking operations.
ENVIRONMENTAL PROTECTION
This symbol gives indications for the use of the
machine with respect for the environment.
IMPORTANT INFORMATION
This symbol indicates important information that
you must bear in mind.
This symbol indicates a list.

5 20153481
GB
Information and general warnings
2.1.4 Delivery of the system and the instruction
manual
When the system is delivered, it is important that:
the instruction manual is delivered to the user by the system
manufacturer, with the recommendation to keep it in the
room where the heat generator is to be installed.
The instruction manual shows:
– the serial number of the burner;
– the address and telephone number of the nearest Assis-
tance Centre;
The system supplier must carefully inform the user about:
– the use of the system;
– any further tests that may be required before activating the
system;
– maintenance, and the need to have the system checked at
least once a year by a representative of the manufacturer
or another specialised technician.
To ensure a periodic check, the manufacturer recom-
mends the drawing up of a Maintenance Contract.
2.2 Guarantee and responsibility
The manufacturer guarantees its new products from the date of
installation, in accordance with the regulations in force and/or the
sales contract. At the moment of the first start-up, check that the
burner is integral and complete.
In particular, the rights to the guarantee and the responsibility will
no longer be valid, in the event of damage to things or injury to
people, if such damage/injury was due to any of the following
causes:
incorrect installation, start-up, use and maintenance of the
burner;
improper, incorrect or unreasonable use of the burner;
intervention of unqualified personnel;
carrying out of unauthorised modifications on the equipment;
use of the burner with safety devices that are faulty, incor-
rectly applied and/or not working;
installation of untested supplementary components on the
burner;
powering of the burner with unsuitable fuels;
faults in the fuel supply system;
continuation of use of the burner when a fault has occurred;
repairs and/or overhauls incorrectly carried out;
modification of the combustion chamber with inserts that
prevent the regular development of the structurally estab-
lished flame;
insufficient and inappropriate surveillance and care of those
burner components most likely to be subject to wear and
tear;
use of non-original components, including spare parts, kits,
accessories and optional;
force majeure.
The manufacturer furthermore declines any and every re-
sponsibility for the failure to observe the contents of this
manual.
.........................................................................................
.........................................................................................
.........................................................................................
.........................................................................................
WARNING
Failure to observe the information given in this
manual, operating negligence, incorrect installa-
tion and carrying out of non authorised modifica-
tions will result in the annulment by the
manufacturer of the guarantee that it supplies with
the burner.

20153481 6
GB
Safety and prevention
3.1 Introduction
The burners have been designed and built in compliance with
current regulations and directives, applying the known technical
rules of safety and envisaging all the potential danger situations.
It is necessary, however, to bear in mind that the imprudent and
clumsy use of the equipment may lead to situations of death risk
for the user or third parties, as well as the damaging of the burner
or other items. Inattention, thoughtlessness and excessive confi-
dence often cause accidents; the same applies to tiredness and
sleepiness.
It is a good idea to remember the following:
The burner must only be used as expressly described. Any
other use should be considered improper and therefore dan-
gerous.
In particular:
it can be applied to boilers operating with water, steam, diather-
mic oil, and to other uses expressly foreseen by the manufactur-
er;
the type and pressure of the fuel, the voltage and frequency of the
electrical power supply, the minimum and maximum deliveries for
which the burner has been regulated, the pressurisation of the
combustion chamber, the dimensions of the combustion cham-
ber and the room temperature must all be within the values indi-
cated in the instruction manual.
Modification of the burner to alter its performance and desti-
nations is not allowed.
The burner must be used in exemplary technical safety con-
ditions. Any disturbances that could compromise safety must
be quickly eliminated.
Opening or tampering with the burner components is not
allowed, apart from the parts requiring maintenance.
Only those parts envisaged by the manufacturer can be
replaced.
3.2 Personnel training
The user is the person, body or company that has acquired the
machine and intends to use it for the specific purpose. He is re-
sponsible for the machine and for the training of the people work-
ing around it.
The user:
undertakes to entrust the machine exclusively to suitably
trained and qualified personnel;
undertakes to inform his personnel in a suitable way about
the application and observance of the safety instructions.
With that aim, he undertakes to ensure that everyone knows
the use and safety instructions for his own duties.
Personnel must observe all the danger and caution indica-
tions shown on the machine.
Personnel must not carry out, on their own initiative, opera-
tions or interventions that are not within their province.
Personnel must inform their superiors of every problem or
dangerous situation that may arise.
The assembly of parts of other makes, or any modifications,
can alter the characteristics of the machine and hence com-
promise operating safety. The manufacturer therefore
declines any and every responsibility for any damage that
may be caused by the use of non-original parts.
In addition:
3 Safety and prevention
WARNING
The manufacturer guarantees safety and proper
functioning only if all burner components are intact
and positioned correctly.
must take all the measures necessary to pre-
vent unauthorised people gaining access to
the machine;
the user must inform the manufacturer if
faults or malfunctioning of the accident pre-
vention systems are noticed, along with any
presumed danger situation;
personnel must always use the personal pro-
tective equipment envisaged by legislation
and follow the indications given in this man-
ual.

7 20153481
GB
Technical description of the burner
4.1 Burner designation
4 Technical description of the burner
Range: R
Size
Fuel: Natural gas
Gas oil
Gas oil / Methane
Adjustment:
Electrical supply of the system:
3/400/50
3/230/50
Voltage of auxiliaries:
230/50/60
110/50/60
R S 310 MTC FS1/FS2 3/400/50 230/50
BASIC DESIGNATION
EXTENDED DESIGNATION
BLU
3N / 400V / 50Hz
3N / 230V / 50Hz
230V / 50-60Hz
110V / 50-60Hz
Heavy oil
E Electronic cam
EV Electronic cam with variable speed (with Inverter)
P Proportional air/gas valve
BP Two stage (light oil) / Proportional valve (gas)
M Mechanical cam
S
L
LS
N
Head: TC Standard head
TL Long head
Emission: C01 - ...
C02 - MZ
C03 - BLU
C03 - MX
Class 1 EN676
Class 2 EN676
Class 3 EN676
Class 3 EN676
Flame control system:
FS1
FS2
Standard (1 stop every 24 h)
Continuous operation - only with flame
detection electrode (ionisation) use

20153481 8
GB
Technical description of the burner
4.2 Models available
Tab. A
4.3 Burner categories - Countries of destination
Tab. B
4.4 Technical data
Tab. C
(1) Reference conditions: Room temperature 20°C - Gas temperature 15°C - Barometric pressure 1013 mbar - Altitude 0 m a.s.l.
(2) Pressure on the socket 5)(Fig. 5 on page 13) with zero pressure in the combustion chamber and at maximum burner output.
(3) Sound pressure measured in manufacturer's combustion laboratory, with burner operating on test boiler and at maximum rated output. The sound
power is measured with the “Free Field” method, as per EN 15036, and according to an “Accuracy: Category 3” measuring accuracy, as set out in
EN ISO 3746.
Version FS1/FS2
Designation Voltage Start-up Code
RS 310/M BLU FS1/FS2 3/400/50 Star/Triangle 20152646
3/230/50 Direct 20152634
RS 410/M BLU FS1/FS2
3/400/50 Star/Triangle 20152650
3/230/50 Direct 20152640
3/400/50 Direct 20152643
RS 510/M BLU FS1/FS2 3/400/50 Star/Triangle 20152653
RS 610/M BLU FS1/FS2 3/400/50 Star/Triangle 20152657
Gas category Destination country
I2E LU - PL
I2E(R) BE
I2EK NL
I2ELL DE
I2Er FR
I2H AT - BG - CH - CZ - DK - EE - ES - FI - GB - GR - HU - IE - IS -
IT - LT - LV - NO - PT - RO - SE - SI - SK - TR
Model RS 310/M BLU RS 410/M BLU RS 510/M BLU RS 610/M BLU
Type FS1
FS2 1138T 1135T 1136T 1137T
Power(1)
Delivery (1)
min - max kW 400/1200 ÷ 3630 500/1500 ÷ 4450 680/1800 ÷ 5250 1000/2200 ÷ 6250
Fuels Natural gas: G20 (methane gas) - G21 - G22 - G23 - G25
Gas pressure at max. output (2)
Gas: G20/G25 mbar 50.1/74.7 53.1/79.2 59.7/89.1 77.6/115.8
Operation FS1: Intermittent (min. 1 stop in 24 hours)
FS2: Continuous (min. 1 stop in 72 hours)
Standard applications Boilers: water, steam, diathermic oil
Ambient temperature °C 0 - 40
Combustion air temperature °C max 60
Noise levels (3) Sound pressure
Sound power dB(A) 78 89
80
91
82.5
93,5
85
96

9 20153481
GB
Technical description of the burner
4.5 Electrical data
Tab. D
4.6 Burner weight
The weight of the burner complete with its packaging is shown in
Tab . E .
Tab. E
DIRECT START UP
Model RS 310/M BLU RS 410/M BLU
Code FS1
FS2 20152634 - 20152636 20152640 - 20152643
Main electrical supply 3/3N~ 230/400V +/-10% 50 Hz
Fan motor IE3
rpm
V
kW
A
2920
220-240/380-415
7.5
25.2/14.5
2930
230/400
9.2
28.6/16.5
Ignition transformer V1 - V2
I1 - I2
230 V - 1 x 8 kV
1 A - 20 mA
Absorbed electrical power kW max 9,1 10,9
Protection level IP 54
STAR - TRIANGLE START UP
Model RS 310/M BLU RS 410/M BLU RS 510/M BLU RS 610/M BLU
Code FS1
FS2 20152646 20152650 20152653 20152657
Main electrical supply 3N ~ 400V +/-10% 50 Hz
Fan motor IE3
rpm
V
kW
A
2910
400/690
7.5
13.9/8.0
2930
400/690
9.2
16.5/9.6
2920
400/690
12
21/12.2
2915
400/690
15
26.8/15.5
Ignition transformer V1 - V2
I1 - I2
230 V - 1 x 8 kV
1 A - 20 mA
Absorbed electrical power kW max 9.1 10.9 13.8 17.1
Protection level IP 54
Model kg
RS 310/M BLU 250
RS 410/M BLU 250
RS 510/M BLU 250
RS 610/M BLU 280
Fig. 1
20071246

20153481 10
GB
Technical description of the burner
4.7 Maximum dimensions
The maximum dimensions of the burner are given in Fig. 2.
Bear in mind that inspection of the combustion head requires the
burner to be opened and the rear part turned on the hinge.
The maximum dimensions of the open burner are indicated by
the L and R positions.
The l position is reference for the refractory thickness of the boiler
door.
Tab. F
** Maximum position for the extraction of the servomotor cover.
WARNING
*The gas adaptor is set also for DN 80 bore.
Fig. 2
20071247
mm A B C D E F* G H I L M N O P** R
RS 310/M BLU 1178 465 178 306 520 DN65 890 790 346 1015 400 528 290 177 890
RS 410/M BLU 1178 517 178 313 520 DN65 908 790 340 1015 400 528 290 177 890
RS 510/M BLU 1178 517 178 313 520 DN65 908 790 340 1015 400 528 290 177 890
RS 610/M BLU 1178 517 178 334 520 DN65 980 790 365 1015 400 528 290 177 890

11 20153481
GB
Technical description of the burner
4.8 Firing rates
The MAXIMUM OUTPUT is chosen from within the diagram area
(Fig. 3).
The MINIMUM OUTPUT must not be lower than the minimum
limit of the diagram:
Tab. G
Model kW
RS 310/M BLU 400
RS 410/M BLU 500
RS 510/M BLU 680
RS 610/M BLU 1000
WARNING
The firing rate value (Fig. 3) has been obtained
considering an ambient temperature of 20°C, an
atmospheric pressure of 1013 mbar (approx. 0 m
a.s.l.), and with the combustion head adjusted as
shown on page 22.
Thermal power – kW
400 800 1200 1600 2000 2400 2800 3200 3600 4000 4400 4800
0
2
4
6
8
10
12
14
16
18
5200 5600 6000 6400 6800
-2
20
Fig. 3
Combustion chamber
combustion head - mbar
20058566
RS 310/M
RS 410/M
RS 510/M
RS 610/M

20153481 12
GB
Technical description of the burner
4.9 Test boiler
The burner/boiler combination does not pose any problems if the
boiler is EC approved and its combustion chamber dimensions
are similar to those indicated in the diagram (Fig. 4).
If the burner must be combined with a boiler that has not been EC
approved and/or its combustion chamber dimensions are clearly
smaller than those indicated in the diagram, consult the manufac-
turer.
The firing rates were set in relation to special test boilers, accord-
ing to EN 676 regulations.
In Fig. 4 you can see the diameter and length of the test combus-
tion chamber.
Example: RS 610/M BLU
Output 5000 kW - diameter 100 cm - length 5 m
4.10 Burner equipment
Gasket for gas train adaptor. . . . . . . . . . . . . . . . . . . . . . . . No. 1
Adaptor for gas train. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1
Screws for fixing the gas train adaptor: M 16 x 70 . . . . . . . No. 4
Thermal insulation screen . . . . . . . . . . . . . . . . . . . . . . . . . No. 1
M 18 x 60 screws to secure the burner flange
to the boiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 4
Cable grommets kit for optional electrical wiring input . . . . No. 1
M16 x 6 studs for fixing the gas elbow
to the pipe coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 4
M16 nuts to fix the gas elbow to the pipe coupling . . . . . . No. 4
Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1
Spare parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1
Fig. 4
20057548
Combustion chamber
m

13 20153481
GB
Technical description of the burner
4.11 Burner description
1 Lifting rings
2Fan
3Fanmotor
4 Air damper servomotor
5 Combustion head gas pressure test point
6 Combustion head
7 Ignition electrode
8 Flame stability disk
9 Electrical panel casing
10 Hinge for opening the burner
11 Fan air inlet
12 Pipe coupling
13 Gasket for boiler fixing
14 Adjustable profile cam
15 Shutter
16 Combustion head movement screw
17 Air damper control lever
18 Air pressure switch
19 Combustion head air pressure test point
20 Maximum gas pressure switch with pressure test point
21 Flame sensor probe
22 Pressure test point for air pressure switch “+”
23 Gas train adapter
24 Gas butterfly valve control lever
25 Indication for checking the rotation direction of the purging
motor
26 Flame inspection window
27 Provision for UV sensor kit
28 Reset button
29 Transparent protection
22
9110 16 1615
8
24
14
17 11
26
23
20
10
721
18
12
19
5
13
32
4
27
25
ON
OFF
29
28
Fig. 5
20156542
The burner can be opened to the right or to the left
without links to the fuel supply side.
WARNING
To open the burner see section “Access to head
internal part” on page 20.

20153481 14
GB
Technical description of the burner
4.12 Electrical panel description
1 Ignition transformer
2 Burner state indicator light and reset button. For further
information see section “Burner ignition” on page 28
3 OFF-automatic-manual selector
4 Electrical control box
5 Power increase - power reduction selector
6 Earth terminal
7 Air pressure switch
8 Bracket for applying the kits
9 Relay with clean contacts for signalling the burner is operat-
ing
10 Relay with clean contacts for signalling the burner is in lock-
out
11 Auxiliary circuits fuse (includes a spare fuse)
12 Timer for star/triangle start up
13 Main terminal supply board
14 Supply cables and external connections passage. See sec-
tion “Electrical wiring” on page 26
15 Motor cables sheath
16 Maximum gas pressure switch sheath
17 Servomotor sheath
18 Direct start up line contactor
19 Thermal relay (with reset button)
20 Triangle contactor (Star/triangle start up)
21 Star contactor (Star/triangle start up)
22 Auxiliary contacts (Star/triangle start up)
23 Ionisation probe cable
24 Star/triangle start-up line contactor
18
19
9
10
22
24
19 20
21
12
14
13
15
8
7
5
3
2
4
1
23
6
6
14
20156522
Fig. 6
STAR/TRIANGLE
STARTER
DIRECT START
Fig. 7
6
6
17
10
6
11
16
9
20156519

15 20153481
GB
Technical description of the burner
4.13 RFGO-A22 control box
Warnings
All interventions (assembly and installation operations,
assistance, etc.) must be carried out by qualified personnel.
Before modifying the wiring in the control box connection
area, fully disconnect the system from the power supply
(omnipolar separation). Check the system is not powered
and cannot be accidentally reconnected. Failure to do this
will lead to the risk of electrocution.
Protection against electrocution from the control box and all
connected electric components is obtained with the correct
assembly.
Before any intervention (assembly and installation opera-
tions, assistance, etc.), ensure the wiring is in order and that
the parameters are correctly set, then make the safety
checks.
Falls and collisions can negatively affect the safety func-
tions.
In this case, the control box must not be operated, even if it
displays no evident damage.
For the safety and reliability of the control box, comply with the
following instructions:
– avoid conditions that can favour the development of conden-
sate and humidity. Otherwise, before switching on again,
make sure that the entire control box is perfectly dry!
– Static charges must be avoided since they can damage the
control box’s electronic components when touched.
Technical data
Tab. H
Mechanical structure
The control box is made of plastic to resist knocks, heat and
flame propagation.
The electronic flame signal amplifier is integrated into the control
box.
WARNING
To avoid accidents, material or environmental
damage, observe the following instructions!
The control box is a safety device! Avoid opening
or modifying it, or forcing its operation. Riello
S.p.A. cannot assume any responsibility for dam-
age resulting from unauthorised interventions!
Mains voltage AC 230 V -15 % / +10 %
Mains frequency 50 / 60 Hz
Primary fuse (external) max. 10 A
Weight approx. 1 kg
Power absorption approx. AC 3.5 VA
Protection level IP40
Safety class II
Environmental conditions:
Operation
Mechanical conditions
Temperature range
Humidity
DIN EN 60721-3-1
Class 1K2
Class 1M2
-40...+60 °C
< 95 % r.h. (without condensing)
Fig. 8
20152163

20153481 16
GB
Technical description of the burner
4.14 Servomotor SQM40 ...
Warnings
All interventions (assembly and installation operations,
assistance, etc.) must be carried out by qualified personnel.
Falls and collisions can negatively affect the safety func-
tions. In this case, the servomotor must not be operated,
even if it displays no evident damage.
Fully disconnect the burner from the mains when working
near terminals and servomotor connections.
Condensation and exposure to water are not allowed.
For safety reasons, the servomotor must be checked after
long periods of non-use.
•
Technical data
WARNING
To avoid accidents, material or environmental
damage, observe the following instructions!
Avoid opening, modifying or forcing the servomo-
tor.
Mains voltage 230 V -15% +10%
Mains frequency 50 / 60 Hz
Power absorption 7 ... 15 VA
Motor Synchronous
Drive angle Varying between 0° and 135°
WARNING
Absolutely do not adjust the red cam No. 1 more
than 90° to prevent serious or irreversible damage
to the mechanical adjustment parts.
Protection level Max. IP 66, with appropriate
cable entry
Cable entry 2 x M16
Cable connection terminal board for 0.5mm2(min.)
and 2.5mm2(max.)
Rotation direction Anticlockwise
Rated torque (max.) 10 Nm
Holding torque 5 Nm
Operation time 30 s. at 90°
Weight approx. 2 kg
Environmental conditions:
Operation
Transport and storage
-20....+60° C
-20...+60°C
Fig. 9
S8907

17 20153481
GB
Technical description of the burner
4.15 Calibration of the thermal relay
The thermal relay serves to avoid damage to the motor due to an
excessive absorption increase or if a phase is missing.
For calibration 2), see the table in the wiring diagram.
To reset, in case of an intervention of the thermal relay, press the
“RESET” button 1) of Fig. 10.
The red “TEST” button 3) opens the NC (95-96) contact and
stops the motor.
4.16 Motor rotation
As soon as the burner starts up, go in front of the cooling fan of
the fan motor and check it is rotating anticlockwise (Fig. 11).
If this is not the case:
set the burner switch to “0” (off) and wait for the control box
to carry out the switch-off phase.
Invert the phases on the three-phase motor power supply.
CAUTION
The automatic reset can be dangerous. This oper-
ation is not foreseen in the burner operation.
Therefore do not position the “RESET” button
1) on “A”.
3
1
2
RESET
HA
TEST
95 96 97 98
Fig. 10
20073932
DANGER
Disconnect the electrical supply from the burner
by means of the main system switch.
Fig. 11
20162422

20153481 18
GB
Installation
5.1 Notes on safety for the installation
After carefully cleaning all around the area where the burner will
be installed, and arranging the correct lighting of the environ-
ment, proceed with the installation operations.
5.2 Handling
The burner packaging includes a wooden platform, it is therefore
possible to move the burner (still packaged) with a transpallet
truck or fork lift truck.
5.3 Preliminary checks
Checking the consignment
Checking the characteristics of the burner
Check the identification label of the burner, showing:
the model (A)(Fig. 12) and type of burner (B);
the year of manufacture, in cryptographic form (C);
the serial number (D);
the data for electrical supply and the protection level (E);
the absorbed electrical power (F);
the types of gas used and the relative supply pressures (G);
the data of the burner's minimum and maximum output pos-
sibilities (H) (see Firing rate)
Warning. The burner output must be within the boiler's firing
rate;
the category of the appliance/countries of destination (I).
5Installation
DANGER
All the installation, maintenance and disassembly
operations must be carried out with the electricity
supply disconnected.
WARNING
The installation of the burner must be carried out
by qualified personnel, as indicated in this manual
and in compliance with the standards and regula-
tions of the laws in force.
DANGER
Combustion air inside the boiler must be free from
hazardous mixes (e.g.: chloride, fluoride, halo-
gen); if present, it is highly recommended to carry
out cleaning and maintenance more frequently.
WARNING
The handling operations for the burner can be
highly dangerous if not carried out with the great-
est attention: keep any unauthorised people at a
distance; check the integrity and suitableness of
the available means of handling.
Check also that the area in which you are working
is empty and that there is an adequate escape
area (i.e. a free, safe area to which you can quick-
ly move if the burner should fall).
When handling, keep the load at not more than
20-25cm from the ground.
After positioning the burner near the installation
point, correctly dispose of all residual packaging,
separating the various types of material.
CAUTION
Before proceeding with the installation operations,
carefully clean all around the area where the burn-
er will be installed.
CAUTION
After removing all the packaging, check the integ-
rity of the contents. In the event of doubt, do not
use the burner; contact the supplier.
The packaging elements (wooden cage or card-
board box, nails, clips, plastic bags, etc.) must not
be abandoned as they are potential sources of
danger and pollution; they should be collected and
disposed of in the appropriate places.
WARNING
A burner label, or any other component, that has
been tampered with, removed or is missing, pre-
vents the definite identification of the burner and
makes any installation or maintenance work diffi-
cult
R.B.L.
GAS- KAASU
GAZ- AEPI O
X
RIELLOS.p .A.
I-37045 Legnago ( VR)
A
DE
BC
F
I
G H
G H
Fig. 12
D10411