Rigol DS4024 User manual

RIGOL DS4024 OSCILLOSCOPE
STUDENT INNOVATION CENTER
ROOM 2222
Wade Warman
Dayon Royster
VERSION 1.0
2/11/2021

CONTENTS
OVERVIEW...........................................................................1
HEALTH & SAFETY INFO......................................................2
HAZARD CONTROL MEASURES/REQUIRED PPE...............3
FIRST AID PROCEDURES.....................................................4
WASTE DISPOSAL...............................................................5
SPILL/CLEAN UP PROCEEDURES.......................................6
OPERATIONS GUIDE...........................................................7
APPENDIX: FRONT PANEL FUNCTION OVERVIEW .........37

OVERVIEW
01
The purpose of this document is to provide standard operating
procedures for the use of the Rigol DS4024 Oscilloscope in room
2222 of the Student Innovation Center.
Prior to engaging in hands-on training and operation, these re-
quired training modules MUST be completed:
• Shop Safety Fundamentals
• Fire Safety and Fire Extinguisher Training
• Hazard Communication Training (aka Worker Right to Know)
• Portable Power Tool Safety

Chemical Vapors: Heating of solder can generate toxic vapors
and vapors with high volatile organic compounds (VOCs).
Hot Surfaces: Circuits and soldering equipment generate heat.
Such surfaces must be guarded and labeling must warn users of
the hazards.
Mechanical Hazards: Moving parts must be guarded to prevent
accidental contact. Guards must never be bypassed.
Electrical: Contact with energized parts can lead to injury or
even death. Before each use, inspect for any damaged wiring
and safeguards. Do not use if problems are found. Ensure the
oscilloscope is properly grounded and plugged directly into an
outlet.
HEALTH & SAFETY INFO
02

REQUIRED PPE:
• Safety glasses
• Closed toed shoes
Hazard Control Measures:
• Always use the grounding strap when operating equipment
• No food/drink
• Electric shock can be dangerous and possibly deadly! If you
are unfamiliar with the electricity requirements of your project,
ask a shop staff for assistance
HAZARD CONTROL MEASURES
AND REQUIRED PPE
03

04
FIRST AID PROCEDURES
BURNS: Minor burns are typically small, red, have swelling, and
can blister. Cool burns with cold water and continue until the
pain lessens. After cooling, cover with a dry, sterile bandage or
clean dressing. Consult a physician as needed.
CUTS/SCRAPES: Minor cuts and scrapes usually stop bleeding
on their own. If needed, apply gentle pressure with a clean
bandage or cloth and elevate the wound until bleeding stops.
Clean the wound and apply bandages. Consult a physician as
needed.
PINCH/CRUSH: Consult a physician as needed.
INHALATION: Ensure there is proper ventilation prior to use. If
needed, stop the procedure and move to a well ventilated
area. Consult a physician as needed.
EYES: Immediately irrigate the eyes at an eyewash station for at
least 15 minutes. Hold the eyelids away from the eyeball, mov-
ing eye in all directions to wash thoroughly behind the eyelids.
Consult a physician as needed.
All accidents and injuries occurring at work or in the course of
employment must be reported to the employee’s supervisor as
soon as possible (even if no medical attention is required).
http://www.ehs.iastate.edu/occupational/accidents-injuries

05
WASTE DISPOSAL
If you have left over parts/materials that are stil useable, you
may donate them to the shop for other users.
Dispose of any un-usable left over wires, components, solder
drips, etc. into the waste bin.

06
SPILL/CLEAN UP PROCEDURES
If using solder, do not touch solder drips for 30 seconds to allow
solder to cool. After 30 seconds, wipe off surface(s) and dispose
of in the waste bins.

07
OPERATIONS GUIDE
PLEASE NOTE: This guide is meant to cover the basic operations
of creating measurements using the oscilloscope.
For a more detailed description of the front panel features,
please refer to the Appendix.
Additionally, there are many features and fuctions available
that are beyond the scope of this guide and it is recommended
to read the manufacturers manual for a full detailed description
of all features, functions, and operations.
If you need help, please ask the shop staff!

08
1. Turn on the power to the oscilloscope and wait for it to ini-
tialize

09
2. Attach the probe to the BNC terminal of the oscilloscope

10
3. Connect the probe’s ground clip to ground in the circuit

11
4. Connect the probe’s measuring clip to the point within
your circuit you wish to measure

12
5. Press the “Auto” button on the front panel.
NOTE: The waveform auto setting function requires that the fre-
quency of sine should be no lower than 20 Hz. If the parameter
exceeds this limit, the waveform auto setting function might be
invalid.

13
6. You should see your waveform on the screen

14
7. On the right side of the screen you will see 4 options: pe-
riod, frequency, leading edge, and trailing edge. These are
common parameters used to analyze your signal. Pressing
one of the corresponding soft keys allows you to take a clos-
er look at that element of your waveform.

15
8. If you press one of the 4 softkeys and want to return back
to the original screen/menu, press the “Auto” button once
again

16
9. You can adjust the Horizontal scale by turning the horizon-
tal scale dial. (The grid units are displayed in the upper left of
the screen)

17
10. You can zoom into the horizontal view by pressing the
dial.

18
11. To return to the default view, press the scale button
again