RIKA DOMO MultiAir User manual

Assembly Instructions
DOMO
MULTIAIR

20
Option for first convection fan
Scope of Delivery E15632
B17528 Support plate including convection fan compl.
4 x N106472 Duo Taptite
LB00630 Air deflector complete
2 x N106472 Duo Taptite
L02724 Motor cover
Supplement for second convection fan
Scope of Delivery E15633
B17527 Convection fan complete
3 x N112040 Duo Taptite
L02724 Motor cover
Explanations to symbols
...Important note
#8
...Hex #8
...Useful tip
#10
...Hex #10
...Manually
#25
...Hexalobular
T25
...Hacksaw ...Spanner #13
#13

|
21
EN
20
Dimensions
K1-H
K2-H
K2-S
K1-S
Convection Air Connection
Ø Diameter [mm] 100
K1 - H Connection Height [cm] 80
K1 - S Side Distance [cm] 30
K2 - H Connection Height [cm] 51
K2 - S Side Distance [cm] 22
Note
Only work on the unit when the mains plug has been disconnected and the
stove has cooled down completely.
Note
During assembly / dismantling do not allow objects (screws etc.) to fall into
the pellet container – they can block the screw conveyor and damage the
stove.
Note
During any conversion work, take particular care of your fingers and any
panels and stove attachments. Select soft bases to prevent scratches to your
living space furniture and stove panels.
General information
QThe convection air amount and temperature is designed for heating one or,
if two fans are installed, two additional rooms.
QNote the regional specific fire safety regulations and clarify the connection
situation with the competent authority.
QThe max. temperature of the convection air is 180° C at the air outlet.
QThe convection air should be as short as possible.
QKeep the number of deflections as small as possible.
Note
Please pay attention to the national and country-specific building and fire
regulations when connecting the convection air pipes. Installation and
assembly must be performed by a trained specialist only.
The option MultiAir is basically only with the lower flue pipe connections (rear
/ rear center / side) possible. If only one convection fan is mounted, it can be
combined with the increased rear connections. In this case, leave out the lower
air deflector.
Mounting Convection Fan
Prepare the following at the stove:
Loosen the 4 screws on the rear panel. The rear panel tilts backwards, then
you can lift it off.
Depending on the desired option cut off the two upper markers for one fan, for
the second fan in addition the two bottom markers.
The pre-assembled fan unit must be disassembled for installation. Loosen the
screws and remove the entire fan housing with motor and the oval sensor cover.
Remove the cable cover which is secured with cable ties.
Now mount the lower air deflector on the support plate of the fan.
Loosen the screw of the flame sensor and remove it.
#25
#8
#10
#8
#8

22
Loosen the marked screw from the stove. This is used to secure the air
deflector below.
Then mount the support plate with 5 screws to the stove.
Thread the flame sensor through the oval hole in the support plate and fix it
with the screw.
Mount the flame sensor cover to this support plate. The flame sensor cable
must be routed through the slotted cover to the outside. Then screw on the fan
housing with 3 screws.
Tip
If you install both convection fans, remove now the lower round cover and the
cable channel and fit here the second fan housing.
Mount the cable channel again after screwing the second convection fan.
Insert the wires from flame sensor and fan in the cable channel and put on the
lid.
To fix this and to avoid vibrations, twist the two tabs (located diagonally) with
pliers.
Note
All cables must be protected from heat. Improper installation can damage
your stove and void your warranty.
Run the cable further through the two recesses at the heat deflectors.
Run the cable between the here shown transparent supply air duct and the
conveyor trough back to the green marked vertical cable duct.
#8
#8
#8
#10
#8
#8

|
23
EN
22
Loosen the nut and the ring from the capacitor.
Attach the condenser (with 2 blowers both capacitors) in the free slots behind
the cable channel.
In the cable channel are the three pin connector M3 for the upper convection
fan 1 and the plug M4 for the lower convection fan 2. Insert the correct cable
and put all cables and plugs back into the cable channel.
Install the rear wall of the stove. The fan motor must be covered with the motor
cover. This is only hanged in. If the cover causes noise due to vibration, the
location lugs can be twisted with pliers.
Install the side cover of the stove.
Note
Operation without a cover is not allowed for security reasons. Disregard voids
your warranty and no liability is accepted for damage.
Now test the function of the fan. Connect the power cord back in and select the
Setup menu / Settings submenu Convection Fan.
There are both fans to choose, even if only one was built in. Make your settings.
At the menu Info - Outputs the item Convection fan shows whether the fan
is activated or not.
#13
#13

Technical and design changes, as well as typesetting and printing errors reserved
© 2015 | RIKA Innovative Ofentechnik GmbH
RIKA Innovative Ofentechnik GmbH
4563 Micheldorf /Austria, Müllerviertel 20
Telefon: [phone] - 41, Fax-DW: 43
E-Mail: [email protected]
RIKA.AT
Z36198_Domo_multiAir_DE_FR_IT_EN_NL | 12.01.2016