Riken Keiki SD-1GH User manual

PT2E-16910
Smart Transmitter/Gas Detector Head
SD-1GH
Operating Manual
(PT2E-169)
(PT2-169)

Operating Precautions
This detector is a gas detector that detects combustible gases in the air and triggers a gas alarm.
The gas detector is a safety unit, not an analyzer or densitometer which performs quantitative/qualitative
analysis/measurement for gases.
Please fully understand the following points before using it, so that it can be used properly.
1. This detector may be interfered by gases and vapors other than the gas to be detected.
Please note that the alarm may be triggered by interference. In addition, it may be fluctuated by
environmental (temperature, humidity, etc.) changes in the installation site.
2. The alarm must be set within a range where the performance of the detector can be ensured.
In facilities compliant with the High Pressure Gas Safety Act, an alarm setting below our standard alarm
setpoint may trigger a false alarm.
3. This is a safety unit, not a control unit.
The alarm contact output of the detector must be used for an external alarm lamp/buzzer, while the
alarm signal output must be used for an indicator or external recorder.
If these outputs are used to control other units, we shall not be responsible for any malfunctions.
4. The gas sensing part of the gas detection sensor installed in this detector is made of metal porous
sintered alloy permeated with an oxidation catalyst.
If silicon or sulfide compounds are accumulated on the surface of porous sintered alloy, the area of the
gas sensing part becomes smaller, which may results in serious deterioration of its sensitivity.
For safety reasons, do not use the detector under the presence of silicon or sulfide compounds even
though their amount is very small.
5. For maintenance of the detector, it must go through a regular maintenance, including replacement and
adjustment of the regular replacement parts as specified in the operating manual. In addition, because
this is a safety unit, it is recommended that a regular maintenance and a gas calibration are performed
every six months in accordance with the regulations.

- 1 - SD-1GH
<Contents>
1 Outline of the Product ................................................................................................... 2
1-1. Preface ........................................................................................................................ 2
1-2. Purpose of use ............................................................................................................ 2
1-3. Definition of DANGER, WARNING, CAUTION, and NOTE.......................................... 2
1-4. Method of confirmation for Standards and Explosion proof specification.....................
2 Important Notices on Safety.......................................................................................... 4
2-1. Danger cases .............................................................................................................. 4
2-2. Warning cases ............................................................................................................. 5
2-3. Precautions.................................................................................................................. 6
2-4. Safety information........................................................................................................ 7
3 Product Components .................................................................................................... 9
3-1. Main unit and standard accessories ............................................................................ 9
3-2. Names and functions for each part.............................................................................. 10
3-3. Block diagram.............................................................................................................. 11
4 How to Use ................................................................................................................... 12
4-1. Before using the detector............................................................................................. 12
4-2. Precautions for installation points ................................................................................ 12
4-3. Precautions for system designing................................................................................ 13
4-4. How to install ............................................................................................................... 15
4-5. How to wire.................................................................................................................. 16
5 How to Operate............................................................................................................. 21
5-1. Preparation for start-up................................................................................................ 21
5-2. Basic operating procedures ......................................................................................... 21
5-3. How to start the detector.............................................................................................. 22
5-4. Modes.......................................................................................................................... 24
5-5. User mode ................................................................................................................... 25
5-6. How to exit................................................................................................................... 27
6 Operations and Functions............................................................................................. 28
6-1. Gas alarm activation.................................................................................................... 28
6-2. Fault alarm activation................................................................................................... 29
6-3. External output operation............................................................................................. 30
6-4. Other functions ............................................................................................................ 31
7 Maintenance ................................................................................................................. 32
7-1. Maintenance intervals and items ................................................................................. 32
7-2. Regular maintenance mode......................................................................................... 34
7-3. Gas calibration method................................................................................................ 43
7-4. Parts replacement........................................................................................................ 46
8 Storage, Relocation and Disposal................................................................................. 47
8-1. Procedures to store the detector or leave it for a long time ......................................... 47
8-2. Procedures to relocate the detector or use it again ..................................................... 47
8-3. Disposal of products .................................................................................................... 47
9 Troubleshooting ............................................................................................................ 48
10 Product Specifications................................................................................................... 50
10-1. List of specifications..................................................................................................... 50
10-2. List of accessories ....................................................................................................... 53
10-3. Detection principle ....................................................................................................... 54
11 Definition of Terms......................................................................................................... 55
3

1 Outline of the Product 1-1. Preface
SD-1GH - 2 -
1
Outline of the Product
1-1. Preface
Thank you for choosing our smart transmitter/gas detector head SD-1GH. Please check that the model
number of the product you purchased is included in the specifications on this manual.
This manual explains how to use the detector and its specifications. It contains information required for
using the detector properly. Not only the first-time users but also the users who have already used the
product must read and understand the operating manual to enhance the knowledge and experience before
using the detector.
Although the number of digits to display varies depending on the detection range, this manual provides
explanation using a detection range from 0 to 100.0 as examples (such as examples of LED display).
1-2. Purpose of use
This detector is a fixed type gas detector head that detects leak of combustible/toxic gases and performs
the alarm activation when the gas concentration is over the setting value.
The detector is a safety unit, not an analyzer or densitometer which performs quantitative/qualitative
analysis/measurement for gases. Please fully understand the features of the detector before using it, so
that it can be used properly.
The detector detects abnormalities in the air caused by presence of gases or other reasons (leak) with
the built-in gas sensor. The concentrations of detected gases are displayed on the seven-segment LED.
The detector has a built-in alarm contact and can be used either as a gas alarm, fault alarm, or common
(gas, fault) alarm.
The detector outputs gas concentration in 4 – 20 mA.
1-3. Definition of DANGER, WARNING, CAUTION, and
NOTE
DANGER This message indicates that improper handling may cause serious damage on
life, health or assets.
W
ARNING This message indicates that improper handling may cause serious damage on
health or assets.
CAUTION This message indicates that improper handling may cause minor damage on
health or assets.
NOTE This message indicates advice on handling.

2 Important Notices on Safety 2-1. Danger cases
SD-1GH - 4 -
DANGER
About explosion-proof
The window plate material is a polycarbonate resin. Do not use organic solvents and alkali types
(liquid or vapor). It may cause the color and shape of the window plate to be changed.
Do not open the lid when applying current.
Do not attempt to repair the detector.
For the lid, use hexagon socket head bolts specified by RIKEN KEIKI.
Do not apply a strong force or shock to the window plate. The explosion-proof performances may
be deteriorated due to damages. The explosion protection conditions for the detector is "low
(2J)" possibility of mechanical damage.
Do not replace parts at your sole discretion but contact RIKEN KEIKI if the transparent window
has a crack or the explosion-proof joint surface is abnormal, or the clamping screw or bolt is
changed, lost etc.
Do not repair the explosion-proof joint surface.
Be careful not to hit sharp tools against the window plate.
2
Important Notices on
Safety
2-1. Danger cases

2 Important Notices on Safety 2-2. Warning cases
- 5 - SD-1GH
WARNING
Power supply
Before turning on the detector, always check that the voltage is properly applied. Do not use an
unstable power supply because it may cause malfunctions.
Need of grounding circuit
Do not cut the grounding circuit or disconnect the wire from the grounding terminal.
Defects in protective functions
Before starting the detector, check the protective functions for defects. When seeming defects are
found in the protective functions, such as protective grounding, do not start the detector.
External connection
Before connecting the detector to the external control circuit, securely connect it to a protective
grounding circuit.
Zero adjustment in the atmosphere
When the zero adjustment is performed in the atmosphere, check the atmosphere for freshness
before beginning the adjustment. If other gases exist, the adjustment cannot be performed properly,
thus leading to dangers when the gas leaks.
Response to gas alarm
Issuance of a gas alarm indicates that there are extreme dangers. Take proper actions based on
your judgment.
2-2. Warning cases

2 Important Notices on Safety 2-3. Precautions
SD-1GH - 6 -
CAUTION
Do not use a transceiver near the detector.
Radio wave from a transceiver near the detector or its cables may disturb indication reading. If a
transceiver is used, it must be used in a place where it disturbs nothing.
To restart the detector, wait for five seconds or more before doing it.
Restarting the detector within five seconds may cause errors.
Do not use the external output of the detector to control other units.
This is not a control unit. It is not allowed to use the external output of the detector to control other
units.
Do not disassemble/modify the detector, or change the settings if not necessary.
Disassembling/Modifying the detector will invalidate the warranty of the performance. Changing the
settings without understanding the specifications may cause alarm malfunctions. Please use the
detector properly in accordance with the operating manual.
Avoid applying organic solvents and others to the window plate for a long time.
The window plate material is a polycarbonate resin. When organic solvents (liquid or
highly-concentrated vapor) and others are applied to the plate for a long time, its color and shape
may be changed.
Do not forget to perform a regular maintenance.
Since this is a safety unit, a regular maintenance must be performed to ensure safety. Continuing to
use the detector without performing a maintenance will deteriorate the sensitivity of the sensor, thus
resulting in inaccurate gas detection.
2-3. Precautions

3 Product Components 3-1. Main unit and standard accessories
- 9 - SD-1GH
3
Product Components
3-1. Main unit and standard accessories
<Main Unit> (including a cable gland)
【ATEX/IECEx Specification】
【TIIS Specification】

3 Product Components 3-2. Names and functions for each part
SD-1GH - 10 -
CAUTION
Use the supplied dedicated control key to operate the detector. If products other than these
accessories are used, key operations cannot be accepted properly.
<Standard Accessories>
Operating manual
Dedicated handling lever (used for the wiring)
Dedicated control key
3-2. Names and functions for each part
(1) MENU/ESC key Used to enter the maintenance mode.
It is also used to cancel in a specific mode.
(2) SET key It is used for value confirmation and so on in a specific mode.
(3) ▲key Used to switch menus or change a value (UP).
(4) ▼key Used to switch menus or change a value (DOWN).
(5) Power lamp
Power lamp:
Detection mode: It lights up in green.
Maintenance mode: It blinks in green.
(6) Alarm lamp Alarm lamp. It lights up in red when the alarm setpoint value is
reached.
(7) Fault lamp Fault lamp. It lights up in yellow when an abnormality is detected in
the detector.
(8) Concentration value display Displays the gas concentration and so on.
(8) Concentration
value display
(5) Power lamp (6) Alarm lamp (7) Fault lamp
(1) MENU/ESC key
(2) SET key (4) ▼key
(3) ▲key

3 Product Components 3-3. Block diagram
- 11 - SD-1GH
3-3. Block diagram
<Electric Diagram>
Sensor
Controller
(CPU)
POWER INPUT (24 VDC)
Power supply part
Gas alarm contact (ALARM)
Contact activation
• De-energized
(De-energized at a normal
environment)
• ON-ALARM
(Closed contact at an
alarm time)
Alarm contact controller
Display
(POWER) (ALARM) (FAULT)
Seven-segment LED
(four-digit)
Magnetic operation part
(MENU/ESC) (▲) (▼) (SET)
Transmitter
• 4 – 20 mA transmission

4 How to Use 4-1. Before using the detector
SD-1GH - 12 -
CAUTION
This is a precision device. Because the detector may not provide the specified performance in some
places (environments), check the environment in the installation point, and then take appropriate
actions if necessary.
Because the detector plays an important role for safety and disaster prevention, as many units of
the detector as needed must be installed in appropriate points.
Because points where gases leak and remain easily are different depending on the types of gases
and the working areas, please decide carefully on installation points and the number of units to be
installed.
4
How to Use
4-1. Before using the detector
Not only the first-time users but also the users who have already used the product must follow the operating
precautions.
Ignoring the precautions may damage the detector, resulting in inaccurate gas detection.
4-2. Precautions for installation points
Do not install the detector in a place with vibrations or shocks.
The detector consists of sensitive electronic parts. The detector must be installed in a stable place without
vibrations or shocks and it cannot drop.
Do not install the detector in a place exposed to water, oil or chemicals.
When selecting installation points, avoid a place where the detector is exposed to water, oil or chemicals.
Do not install the detector in a place where the range of operating temperatures is exceeded.
The detector must be installed in a stable place where the operating temperature is maintained and do not
change suddenly.
<ATEX/IECEx Specifications> -20 to +60ºC
<TIIS Specifications> -20 to +53ºC
Do not install the detector in a place exposed to direct sunlight or sudden changes in the temperature.
When selecting installation points, avoid a place where it is exposed to direct sunlight or radiant heat
(infrared rays emitted from a high-temperature object), and where the temperature changes suddenly.
Condensation may be formed inside the detector, or the detector cannot adjust to sudden changes in the
temperature.
Keep the detector (and its cables) away from noise source devices.
When selecting installation points, avoid a place where high-frequency/high-voltage devices exist.

4 How to Use 4-3. Precautions for system designing
- 13 - SD-1GH
CAUTION
An unstable power supply and noise may cause malfunctions or false alarms.
The descriptions in this section must be reflected on the designing of a system using the detector.
Do not install the detector in a place where maintenance of the detector cannot be performed or where
handling the detector involves dangers.
Regular maintenance of the detector must be performed.
Do not install the detector in a place where the machinery must be stopped when maintenance is performed
in its inside, where parts of the machinery must be removed to perform maintenance, or where the detector
cannot be removed because tubes or racks prevent access to it. Do not install the detector in a place where
maintenance involves dangers, for example, near a high-voltage cable.
Do not install the detector in machinery which is not properly grounded.
Before installing the detector in machinery, the machinery must be grounded properly.
Do not install the detector in a place where other gases exist around it.
The detector must not be installed in a place where other gases exist around it.
4-3. Precautions for system designing
Using a stable power supply
The external output and alarm contact of the detector may be activated when the power is turned on, when
momentary blackout occurs, or while the system is being stabilized. In such cases, use a UPS, or take
appropriate actions on the receiving side of output signals.
The detector must be provided with the following power supply.
Power supply
voltage 24 VDC (17 – 26.4 VDC): Terminal voltage of the detector
Allowed time of
momentary blackout
Up to 10 milliseconds
(To recover from the momentary
blackout for 10 milliseconds or more,
restart the detector.)
Example of actions
To ensure continuous operation and
activation, install a UPS outside the
detector.
Others
Do not use it with a power supply of
large power load or high-frequency
noise.
Example of actions
Use a line filter to avoid the noise source
if necessary.

4 How to Use 4-3. Precautions for system designing
SD-1GH - 14 -
CAUTION
In principle, do not activate inductive load at the alarm contact of the detector. (In particular,
never use the inductive load to activate a fluorescent lamp or motor.)
If inductive load is activated, relay it with an external relay (contact amplification). However,
because the coil of an external relay also involves inductive load, select a relay at a lower
voltage (100 VAC or below), and then protect the contact of the detector with an appropriate
surge absorbing part, such as a CR circuit.
Introducing protective measures against lightning
If cables are installed outside the factory/plant, or if internal cables are installed in the same duct as the
cables coming from outside the factory/plant, "lightning" will cause problems. Because lightning acts as a
large emission source while cables act as a receiving antenna, devices connected to the cables may be
damaged.
Lightning cannot be prevented. Cables installed in a metal conduit or under the ground cannot be
completely protected from inductive lightning surge caused by lightning. Although complete elimination of
disasters caused by lightning is impossible, the following protective measures can be taken.
Protection against
lightning
Take appropriate measures in accordance with the importance of the facilities
and the environment.
Provide protection by a lightning arrester (cable arrester).
(Although inductive lightning surge can be transmitted through the cable, it is
prevented by installing a lightning arrester before the field devices and central
processing equipment. For information on how to use a lightning arrester,
please contact the manufacturer.)
Grounding In addition to lightning, there are more sources of surge noise. To protect units
from these noise sources, the units must be grounded.
* The lightning arrester has a circuit to remove a surge voltage which damages field devices, so that signals
may be attenuated. Before installing a lightning arrester, verify that it works properly.
Proper use of alarm contact
The alarm contact of the detector is used to transmit signals to activate an external buzzer, an alarm lamp or
a rotating lamp. Do not use the detector for controlling purpose (e.g., controlling the shutdown valve.)
The specifications for the alarm contact of the detector are based on the resistant load conditions. If
inductive load is used at the alarm contact, the following errors will occur easily because counter
electromotive force is generated at the contact.
Deposition, defective insulation or defective contact at the relay contact
Damage of any electric parts due to high-voltage generated inside the detector
Abnormal operations by an out-of-control CPU
If load is to be activated, appropriate measures must be taken to stabilize the operation of the detector and
protect the alarm contact referring to the following information.
Relay it with an external relay at a lower voltage of 100 VAC or below (contact amplification). At the same
time, the surge absorbing part SK1 suitable for the specifications must be attached to the external relay.
In addition, the surge absorbing part SK2 must be attached to the loaded side of the external relay if
necessary.
It may be recommended that the surge absorbing part should be attached to the contact for certain load
conditions. It must be attached to an appropriate position by checking how the load is activated.

4 How to Use 4-5. How to wire
SD-1GH - 16 -
CAUTION
Be careful not to damage the internal electronic circuit when wiring. In addition, be careful not to
apply stresses on the detector when (overweight) cables are installed.
The power cables and signal cables must not be installed together with the motor power cables,
etc. When these cables must be installed together for unavoidable reasons, put the power cables
and signal cables in a metal conduit. The conduit must be connected to a grounding circuit.
When stranded wires are used, prevent wires from contacting each other.
Use the dedicated handling lever to wire.
Use appropriate cables to wire.
4-5. How to wire
<Recommended Cable>
3-wire (when the contact is not used) CVVS1.25 sq - 3-core
5-wire (when the contact is used) CVVS1.25 sq - 5-core
<Parts. length table of outside conductor lead-in>
Cable overall outer
diameter(mm)
Rubber seal inner
diameter(mm)
Washer inner
diameter(mm)
Clamp inner
diameter(mm)
From Φ9.6 to less than Φ10.5 Φ11 Φ12 Φ10.8
From Φ10.5 to less than Φ11.5 Φ12 Φ12 Φ11.8
From Φ11.5 to less than Φ12.5 Φ13 Φ14 Φ12.8
From Φ12.5 to less than Φ13.0 Φ13.5 Φ14 Φ13.8
φ 23