RIOTEC LS6300E User manual

Programming Quick Guide
LS6300E/LS6320E/LS6320V
Installation
Make sure that the scanner has the correct cable to
plug into the PC as below described:
1. USB cable connection: / PS2 cable connection:
(Please use correct cable for the interface)
Reset Configuration to Default
If you are unsure of the scanner configuration or have
scanned the incorrect codes, please read the “Default”
barcode. This will reset the scanner to its factory
default.
Default
2. RS232 cable connection:
Please read above “Default” first, then, set the output
mode as RS232 (SERIAL).
★If you want to switch to different interface, please
scan the correct configuration code (Output Mode,
right above), then, change the appropriate cable.
3. Auto-sensing switch ON/OFF
LS6320E has one button to control auto-sensing
function. Press the auto-sensing button to switch it
ON/OFF (Shown on below photo) Default is ON.
OUTPUT MODE –
KEYBOARD / USB OUTPUT MODE - RS232 (SERIAL)
OUTPUT
MODE
SINGLE SCAN SINGLE SCAN NO TRIGGER
READING
MODE
LASER TIMEOUT
– 5 SECONDS LASER TIMEOUT – 2 SECONDS
CODE 11 DOUBLE
CHECK -ENABLE CODE 11 DOUBLE CHECK -DISABLE
DOUBLE
CHECK
CODE 39 DOUBLE
CHECK -ENABLE CODE 39 DOUBLE
CHECK -DISABLE
CODE 93 DOUBLE
CHECK -ENABLE CODE 93 DOUBLE
CHECK -DISABLE
CODE 128 DOUBLE
CHECK -ENABLE CODE 128 DOUBLE
CHECK -DISABLE
I2OF5 DOUBLE
CHECK -ENABLE I2OF5 DOUBLE
CHECK -DISABLE
DOUBLE
CHECK
ID2OF5 DOUBLE
CHECK -ENABLE ID2OF5 DOUBLE CHECK -DISABLE
CODABAR DOUBLE
CHECK -ENABLE CODABAR DOUBLE
CHECK -DISABLE
UPC/EAN DOUBLE
CHECK -ENABLE UPC/EAN DOUBLE CHECK -DISABLE
REVERSE IMAGE
–ENABLE IMAGE REVERSE IMAGE -DISABLE
SEND BAR CODE ID
-DISABLE CODE ID SEND BAR CODE
ID–AS A PREFIX
SEND BAR CODE ID
-RESET SEND BAR CODE
ID –AS A SUFFIX

Keyboard Language
Scan the appropriate country code below to program the
keyboard for your country or language.As a general rule,
the following characters are not supported by the scanner
for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
DENMARK FINLAND
FRANCE GERMANY
ITALY LATIN AMERICA
NETHERLANDS NORWAY
POLAND SPAIN
SWITZERLAND
(
FRENCH
)
SWITZERLAND
(
GERMAN
)
SWEDEN UNITED KINGDOM
UNIVERSAL UNITED STATES
Symbologies On/OFF-1
CODE 11
– ENABLE CODE 11 CODE 11
– DISABLE
CODE 39
–
ENABLE CODE 39 CODE 39
–
DISABLE
FULL ASCII
–
ENABLE FULL ASCII
–
DISABLE
CODE 93
–
ENABLE CODE 93 CODE 93
–
DISABLE
CODE 128
–
ENABLE CODE 128 CODE 128
–
DISABLE
CODE 128 ISBT
–ENABLE CODE 128 ISBT – DISABLE
CODABAR
–
ENABLE CODABAR CODABAR
–
DISABLE
Symbologies On/OFF-2
INTERLEAVED 2 OF 5
I2OF5 - ENABLE I2OF5 - DISABLE
INDUSTRIAL 2 OF 5
ID2OF5
-
ENABLE
ID2OF5
-
DISABLE
MSI - ENABLE MSI MSI - DISABLE
UPC-A- ENABLE UPC/EAN UPC-A -DISABLE
UPC-E -ENABLE UPC-E -DISABLE
EAN-13 -ENABLE EAN-13 -DISABLE
EAN-8 -ENABLE EAN-8 -DISABLE
●Information in this document is subject to change without notice.
●For more information, please visit:
www.riotec.com.tw 2014.04.07