RIOTEC DC9270 User manual

1
Quick Guide
- DC9270
1
Connect to micro USB port of OTG device
2
3
* Before you use scanner, please switch to "C" for battery
charge for 3~4 hours.
* Under “C mode”, you can raise/lower soft-keyboard
easily. (For USB HID only)
4
DC9270 is with Li-Ion battery inside. When in charging,
please use the original power adaptor of OTG device
(recommend). Through it, it charges both OTG device and
DC9270 internal battery at the same time. When in low
battery (Red LED flashing), please charge it immediately.
LED Indicator Information
Green LED OFF Full charged (Charge mode)
Green LED ON Charging (Charge mode)
Red LED Flashing Low battery (Operation mode)
Attention: Under “Operation mode” please do not charging,
otherwise the OTG device's battery will be charging back to
DC9270’s battery.
5


The touch sensor area is around the central area. There are 2
button triggers on the right and left side.
Please check the above drawing for your reference.
Installation
Before using scanner, please make sure that the OTG device is
fully charged.
1. Under USB HID interface
** When plugged into OTG device, it will be recognized and
begin to scan the barcode.
2. Under USB Serial interface
** Please install PL-2303 driver into your OTG device first.
PL-2303 driver can be downloaded from Google Play
** Connect scanner to your OTG device, then, you can
know which serial port scanner connects to.
** The data you scan will be sent to serial port and your
APP can get the data from serial port directly.
Suction Cup
PU Glue
(Can be used
repeatedly)
Micro USB
cable (OTG)
Exit Windo
w
Li- Ion Battery
O=Operation mode
C=Charge mode
Indicator (LED)
Button Trigger
Touch Trigger Area
Button Trigger
Indicator
(
LED
)
Char
g
e por
t

2
Reset Configuration to Defaults
If you are unsure of the scanner configuration or
have scanned the incorrect codes, please scan the
“Default” barcode. This will reset the scanner to its
factory defaults. (scan from A1 for USB HID, B1 to B4
for USB Serial)
USB HID USB Serial
A1 B1
B2
B3
B4
Note: Please install PL-2303 driver for USB Serial.
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
Abort
Configuration
End
Configuration
Multi-Interface Functions
LOUDER
SOUND
LEVEL MIDDLE
LOWER SILENT
LONG
SOUND /
LED CONTROL MIDDLE
SHORT
Multi-Interface Functions
DOUBLE CHECK
(ENABLE)
DOUBLE
CHECK
DOUBLE CHECK
(DISABLE)
SINGLE SCAN
READING
MODE
SINGLE SCAN
NO TRIGGER
Keyboard Language
DENMAR
K
FRENCH
GERMANY HUNGARY
JAPAN ITALIAN
NORWEGIAN PORTUGAL
SPANISH
SWEDISH
SWITZERLAND USA
VIETNAM

3
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
Abort
Configuration
End
Configuration
1D Symbologies On/OFF - 1
ENABLE CODE 128 DISABLE
ENABLE CODABAR DISABLE
ENABLE
INTERLEAVE
25 DISABLE
ENABLE
INDUSTRIAL
25 DISABLE
1D Symbologies On/OFF – 2
ENABLE UPC-A DISABLE
ENABLE UPC-E DISABLE
ENABLE EAN-13 DISABLE
ENABLE EAN-8 DISABLE
ENABLE MSI DISABLE
ENABLE PLESSEY DISABLE
ENABLE CODE 11 DISABLE
ENABLE TELEPEN DISABLE
ENABLE CODE 39 DISABLE
1D Symbologies On/OFF – 3
ENABLE
CODE 32
ITALIAN PHARMACY DISABLE
ENABLE CODE 93 DISABLE
 Information in this document is subject to change without notice.
 For more information, please visit:
www.riotec.com.tw
R_180504_01