Ripley Utility Tool WS6-M User manual

WS6-M
ADJUSTABLE END STRIPPER
Note: This tool is a manually operated cutting device for polyethylene, (XLPE)cross link polyethylene, and (EPR)
ethylene propylene rubber insulation on 15KV to 46KV cables 22.86mm ( .900”) to 52.07mm (2.030”) in diameter.
OPERATING INSTRUCTIONS
For best results, the end of the cable to be stripped should be cut straight and square using a
hack-saw or curved jaw cable cutters.
Step 2. (Fig. 2) To insert the bushing into the WS6-M, line up rib
on the bushing with the slot on the WS6-M housing. Raise the
cutting blade by depressing outer end and insert the bushing until it
locks into place.
Step 3. (Fig. 3) To adjust the stop bar for desired length of
conductor exposure, loosen set screw located on the end of
the tool body directly above the stop bar. Adjust the stop
bar to the desired length of insulation to be stripped and
tighten the set screw.
Step 4. (Fig. 4) To strip the insulation, insert the cable into the
WS6-M until it comes in contact with cutting edge of the blade.
Always check the blade position with respect to the conductor,
before stripping the insulation.
Fig. 4Fig. 3
Fig. 2
RIB
SLOT
PRESS
CUTTING
BLADE
GRADUATED
STOP BAR
CABLE
BLADE CUTTING
EDGE
SET SCREW
Warning!This tool is not protected against electrical shock! Always use OSHA/ANSI or other industry approved eye protection
when using tools. This tool is not to be used for purposes other than intended. Please read and understand instructions before using
this tool.
Step 1. (Fig 1) Check the bushing by sliding it over
polyethylene insulation (Fig 1A) or semi-con over EPR
insulation (Fig. 1B). The bushing should fit snugly and
still rotate easily on the cable. We recommend the use of
lubricant be used on the semi-con over EPR cable.
Fig. 1A
Fig. 1B
Fig. 1

46 Nooks Hill Road
Cromwell, CT 06416
Phone: [phone]
Int’l: [phone]-2200
Fax: [phone]
e-mail: [e-mail]
Internet: www.ripley-tools.com
Warranty: RIPLEY warrants its products against defective materials and workmanship for a period of one year
from date of shipment from the RIPLEY factory provided the product is utilized in accordance with instructions
and specified ratings.
42363 rev.2
12-01-12 ff
Instructions for WS6-M - Part 2
Step 5. (Fig. 5) Before stripping the insulation, adjust the
blade edge to 0.39mm (1/64”) – 0.79mm (1/32”) above the
conductor surface by inserting the provided hex wrench
through the hole located beneath the tool blade.
Step 6. (Fig. 6) Rotate the tool clockwise around the cable to
remove the insulation. Insulation will peel off until the cable
conductor reaches the stop bar. The blade will automatically
sever the insulation cleanly at the end of the cut.
(Fig. 7) To remove the bushing, depress the lock
release pin on the housing and slide the bushing out.
Fig. 5
Fig. 7
TOOL BLADE
1/16” HEX
WRENCH STRIPPED INSULATION
CURL
LOCK
RELEASE PIN
•Stop bar removal allows infinite stripping of insulation
•Rotating stop bar permits a stripping length of 6.19mm (2-
7/16”)
•WA1 adapter permits the use of the SW2 ratchet wrench
•WA3-M adapter allows strip lengths up to 139.7mm (5-
1/2”), SW2 can also be used with WA3-M for extra leverage
Model
Part #
Blade
Blade Part #
Rotating Stop Bar
Part #
WS 6-M
42360
CB 8-2
12903
42361
WS 6 with WA3-M
42355
CB 8-2
12903
42358
Notes
REPLACEMENT PARTS
WA1
Adapter
SW2
Ratchet Wrench
Fig. 6
Fig. 7
WA3-M
Adapter