RITE-HITE VBR-300 Dok-Lok User manual

Publication: AMEN00120 2017-09-19
VBR-300 Dok-Lok®
VBR-300M Dok-Lok®
VBR-300ALP Dok-Lok®
Vehicle Restraint
Installation Manual
This manual covers units built after serial numbers: VB3001000 and up
Language: English
The English version of this manual shall prevail over any
error in, or conflicting interpretation of, any translations.
NOTICE TO USER. . . . . . . . . . . . . . . .2
SAFETY . . . . . . . . . . . . . . . . . . . . . . . .2
INSTALLATION . . . . . . . . . . . . . . . . . .3
WARRANTY. . . . . . . . . . . . . . . . . . . .12
Model: VBR-300 Model: VBR-300M Model: VBR-300ALP
Hydraulic Vehicle Restraint Manual Vehicle Restraint Manual Vehicle Restraint
with Automatic Light Package.

VBR-300 • VBR-300M • VBR-300ALP Dok-Lok®Installation Manual Rite-Hite®
2 Publication: AMEN00120 2017-09-19
NOTICE TO USER
For best results, have this product serviced by an
authorized Rite-Hite®Representative.
A Planned Maintenance Program (P.M.P.), customized to
your specic operation is available and recommended.
For a P.M.P., contact your local Rite-Hite representative or
Rite-Hite technical support at 414-355-2600.
The Rite-Hite®products in this manual are covered by one or more
of the following U.S. patents: 5882167, 6065172, 6070283, 6085375,
6092970, 6106212, 6116839, 6190109, 6276016, 6311352, 6318947,
6322310, 6360394, 6368043, 6431819, 6488464, 6524053, 6726432,
6773221, 6832403, 6880301, 7032267, 7062814, 7213285, 7216391,
7363670, 7380305, 7503089, 7533431, 7546655, 7584517, 7681271,
7823239, 7841823, 7877831, 7914042, 8006811, 8065770, 8141189,
8191194, 8286757, 8287223, 8303235, 8307956, 8443474, 8464384,
8464846, 8465245, 8497761, 8499897, 8544130, 8547234, 8590087,
8590673, 8616826, 8657551, 8662535, 8678736, 8690087, 8905198,
9010501, 9096170, 9096397, 9126775, 9139384, 9145273, 9150367,
9174811, 9227799, 9230419 and may be covered by additional pending
U.S. and foreign patent applications.
Rite-Hite®, ThinMan™, Safe-T-Lip®, Hydrachek®, Wheel-Lok™, Dok-Lok®,
Dual-Dok®, Safe-T-Strut™, Dok-Commander®, Jumbo™, Hydra-Rite™,
Safe-T-Gate®, Rite-Vu™ Hazard Recognition and Communication System,
and Smooth Transition Dok System™, are trademarks of Rite-Hite®.
SAFETY
Safety Identifications
DANGER
Indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
Indicates a situation which can cause damage to the
equipment, personal property and/or the environment,
or cause the equipment to operate improperly.
NOTE:A note is used to inform you of important
installation, operation, or maintenance information.
Lockout Procedure
Barricade work area and post safety
warnings.
Power supply/control must:
• Be disconnected or locked in OFF
position using a lockout device
approved by local codes.
• Have signage that:
−Clearly states repairs are being made.
− Identies person responsible for lockout condition.
NOTE:Only this person should be able to remove
warnings and lockout device.
−Withstands environmental conditions (weather, wet,
and damp, etc.) and remains readable.
General
DANGER
A qualied electrician should install the wiring in
accordance with local electrical codes.
Use lockout procedures to prevent death or severe
personal injury.
170619

Rite-Hite®Installation Manual VBR-300 • VBR-300M • VBR-300ALP Dok-Lok®
Publication: AMEN00120 2017-09-19 3
DANGER
Post safety warnings and barricade work area,
at dock level and at ground level, to prevent
unauthorized use of the dock position
NOTICE
Whether there is a leveler or not, a 4” thick bumper is
required. DO NOT install a DOK-LOK vehicle restraint
on docks without 4” thick bumpers. For thicker
bumpers consult factory.
Installation Instructions
(All Models)
A DOK-LOK vehicle restraint may be installed on docks
with or without levelers. Consult Rite-Hite for proper
application.
Follow the installation procedure below:
1. Inspect DOK-LOK vehicle restraint materials.
2. Assemble track to base.
3. Install DOK-LOK vehicle restraint to dock face.
4. Install electrical components.
5. Assemble operating bar and install bracket
(300M/300ALP only).
6. Install signs.
7. Verify components and assembly.
8. Lubricate and adjust.
9. Test operation.
Inspect DOK-LOK Materials
(All models)
Open and inspect all materials. Immediately report
any damage or material shortage. Study component
assemblies and determine their proper locations.
Inside Sign
Inside Light
And Control Box
Outside
Light
Sign
Hydraulic
Power Unit
Sign
Junction Box
Sensor Wires
Hoses
Drive Approach
VBR-300
Dok-Lok
Shown
4” Thick
Bumpers
Dock Leveler
FIGURE 2 - FLUSH MOUNT VBR-300 DOK-LOK WITH LEVELER IN RECESSED PIT
INSTALLATION

VBR-300 • VBR-300M • VBR-300ALP Dok-Lok®Installation Manual Rite-Hite®
4 Publication: AMEN00120 2017-09-19
Assemble Track to Base
(All Models)
The VBR can be assembled with a 27” or 29” maximum
height. Refer to the Rite-Hite Application information
provided with the VBR for correct height. Follow the steps
below to assemble roller track to the base.
1. Remove tape securing the barrier rollers to the
barrier. See Figure 3.
Remove
Tape
Holding
Rollers To
Barrier
FIGURE 3 - REMOVE TAPE HOLDING ROLLERS TO BARRIER
2. Position barrier in the bottom of the roller track with
barrier rollers installed.
3. Attach base to roller track using 2 3/4” bolts and nuts
(supplied by others). Use top set of holes for a 27”
mounting height and bottom set of holes for a 29”
mounting height. Verify track is perpendicular to base.
4. Weld plates on base to roller track as shown in Figure 4.
5. Remove bolts used in Step 3.
1/4” 1
3/4” Bolt And Nut
(Supplied By Others)
1/4” 1
Bottom Hole
For 29”
Mounting
Height
Top Hole
For 27”
Mounting
Height
FIGURE 4 - WELD PLATES ON BASE TO ROLLER TRACK
Install DOK-LOK vehicle restraint onto dock face at
specied location by welding to an embedded steel
plate or by using the 8 concrete anchors provided
in conjunction with welding to pit steel and a leveler
frame. Refer to Figure 5.
NOTICE
A plumb roller track plate is required. If the dock
face is not plumb/perpendicular, contact your
Rite-Hite representative or Rite-Hite at
[phone].
The carriage roller track cannot be bent or
deformed. Straighten or replace as required.
For site specic installation refer to Rite-Hite
Application information provided with Dok-Lok vehicle
restraint. When doubt, call Rite-Hite Representative or
Rite-Hite Customer Service at [phone].
NOTE:Some mechanical dock levelers have an
adjusting nut access hole in the leveler front subframe.
If the VBR vehicle restraint roller track interferes with
the access hole, the track plate must be cut to allow
access. Refer to Figure 8, page 7.
NOTE:Some levelers may be slightly recessed within
pit. A shim must be inserted between the roller track
plate and the leveler front subframe and then must be
welded in place. Refer to Figure 9, page 7 for adding a
necessary lip guide.
INSTALLATION

Rite-Hite®Installation Manual VBR-300 • VBR-300M • VBR-300ALP Dok-Lok®
Publication: AMEN00120 2017-09-19 5
NOTICE
8 concrete anchors are provided with each VBR
Dok-Lok vehicle restraint. You must install an
anchor in each roller track plate hole except those
plug-welded to embedded steel.
Anchor Installation Instructions
(All Models)
1. Put DOK-LOK vehicle restraint in place.
2. Drill hole of 5/8” diameter and minimum of 4-5/8”
deep. Clean out hole.
3. Insert anchor and drive flush with roller track plate,
making certain that the threaded wedge is put in first.
Do not disassemble anchor prior to installation.
4. Install all anchors and torque to 60 ft-lbs.
See Figure 5.
Front Pit
Curb Angle
Remove
Track Cover
Before Welding
Across Top
Of Track
1/4”
1/4”
Typ. (2)
Places
Drill 5/8”
Dia. Hole
4-5/8” Deep
For Concrete
Anchor
(8) Places
Approach
VBR-300
Dok-Lok
Shown
FIGURE 5 - ANCHORING ROLLER TRACK PLATE
INSTALLATION

VBR-300 • VBR-300M • VBR-300ALP Dok-Lok®Installation Manual Rite-Hite®
6 Publication: AMEN00120 2017-09-19
Welding Installation Instructions
NOTICE
Never weld on the VBR vehicle restraint after sensing
switches are wired into the control box and power
to the control box is on. Electrical current from the
welder can “feedback” through the circuit and damage
the motor and other components.
(All Models)
If the installation being worked on is a “re-installation” the
following electrical connections must be disconnected
prior to welding. Make sure to LOCKOUT/TAGOUT the
power at the fused disconnect, then remove sensing
switch connections from control box. Once all welding
procedures have been completed, reconnect all wires.
NOTES:
a. Plug weld all holes that are in contact with embedded
mounting plate. All 8 holes must be either plug welded
or anchored. See Figure 6.
b. If any of the mounting holes can not be plug welded,
use anchors at these locations. Follows steps #2 - #4
in the anchor installation instructions.
c. Shims must be the full length of the roller track
mounting plate. Minimum electrode must be 1/8” 7018
or better. See Figure 6.
d. Never install Dok-Lok vehicle restraint directly onto
concrete block or brick dock face. See Figure 6.
e. When welding Dok-Lok vehicle restraint, disconnect
power and ground leads to leveler. See Figure 6.
f. Due to actual conditions, total mounting height may be
different. Refer to Rite-Hite Application Guidelines for
actual mounting height. See Figure 6.
g. Remove weld debris and grind welds as necessary.
h. Touch up paint on all eld installation welds and grind
areas once installation is complete.
Drill 5/8”
Dia. Hole
4-5/8” Deep
For Concrete
Anchor
(2) Places
1/4” Typ.
Typ. (8)
Places
Across Top
Of Track
1/4”
Remove
Track Cover
Before Welding
Embedded
Plate
Front Pit
Curb Angle
Level
Approach
VBR-300
Dok-Lok
Shown
FIGURE 6 - WELDING ROLLER TRACK-FRONT VIEW
Shim As
Required
(6 Shims -
2” wide x
Full Length
Of Track)
Maintain
Straightness
And Plumb
Dock Face
Front Pit
Curb Angle
Roller Track
Plate
Level
FIGURE 7 - WELDING ROLLER TRACK-SIDE VIEW
INSTALLATION

Rite-Hite®Installation Manual VBR-300 • VBR-300M • VBR-300ALP Dok-Lok®
Publication: AMEN00120 2017-09-19 7
Special Application Installation
(All Models)
Cut Roller Track
As Required*
Roller Track
*DO NOT Cut
Track Angle
*DO NOT Cut
Track Angle
Remove Cover
Before Cutting
Front Pit
Curb Angle
Existing
Access Hole
4” Dia.
FIGURE 8 - ROLLER TRACK - FRONT VIEW
1/4”
Remove Excess Material
From Shaded Area
Shim
Existing
Lip Guide
Dock
Leveler
Front
Frame
Angle
FIGURE 9 - ROLLER TRACK - SIDE VIEW
NOTE:Shim as required behind track angles (1/2” thick
minimum bar stock) and weld in place. See Figure 9.
NOTICE
Add length to lip guide as required (supplied by
others). Weld in place as shown in Figure 9.
Do not weld to leveler front frame angle.
Install Hydraulic Components
(VBR-300 Only)
1. Mount hydraulic power unit on dock wall as shown
in Figure 2, page 4 using supplied mounting bracket
(hardware supplied by others). Power unit must be
mounted on side shown and within 24” of control
box. If control box is mounted on the other side of the
dock pit, a junction box will be required. Wiring from
the power unit to control box will be routed over the
dock doorway.
2. Drill two holes through dock wall for hydraulic hoses
to pass through. Make sure holes are free of debris
or sharp edges prior to passing hoses through wall.
Conduit may be required in some applications to
protect hoses.
3. Route hoses from Dok-Lok vehicle restraint, through
dock wall and connect to hydraulic power unit.
4. Secure hoses to dock face to prevent possible
damage. Any extra hosing should be coiled and
secured to the inside dock wall below the power unit.
Hoses
Wire Ties
Mounting
Bracket
Mounting Hardward
(Supplied By Others)
Hydraulic Power Unit
Hoses
Lift
Cylinder
FIGURE 10 - INSTALLING HYDRAULIC COMPONENTS
INSTALLATION

VBR-300 • VBR-300M • VBR-300ALP Dok-Lok®Installation Manual Rite-Hite®
8 Publication: AMEN00120 2017-09-19
Assemble Operating Bar and Install Bracket
(VBR-300ALP & M Only)
1. Assemble operating bar as shown. See Figure 11.
Mount operating bar bracket next to the control box
(hardware supplied by others). Hang operating bar
when not in use.
Operating Bar
3”
Weld
FIGURE 11 - ASSEMBLE OPERATING BAR
When working with electrical or electronic
controls, make sure that the power source has
been locked out and tagged according to OSHA
regulations and approved local electrical codes.
When drilling holes in the box, DO NOT allow the
drill to go too deeply into the box. Damage to the
control systems may occur.
DO NOT turn control box upside down to drill
any access holes. Cover internal electrical
components prior to drilling - this will prevent
debris from contacting the internal electrical
components.
Remove all debris from box using a shop
vacuum. NEVER use air to blow debris from the
control box.
Control Box and Conduit Installation
Procedures.
1. Install the control box on a wall adjacent to the
overhead door at approximately 48” above the floor
level. See Figure 13.
2. Drill a hole for the power supply conduit (by others)
in the bottom of the control box. All holes drilled
through the control box must be through the
bottom of the box.
NOTICE
The control box and all wiring should be installed by
a qualied electrician in accordance with all national
and local electrical codes.
If rigid conduit is installed, bonding must be
maintained between conduit connections by using
ground bushings and a jumper wire.
INSTALLATION

Rite-Hite®Installation Manual VBR-300 • VBR-300M • VBR-300ALP Dok-Lok®
Publication: AMEN00120 2017-09-19 9
Install Electrical Components (All Models)
If the incoming electrical power for the Dok-Lok vehicle
restraint is taken from a nearby electrical appliance, i.e.,
overhead door opener, verify that the amperage is in
accordance with local and federal codes.
The VBR-300 Dok-Lok vehicle restraint requires 120V,
single phase power, 60 Hz power and 15 amps of current,
for the 1/3 HP hydraulic power unit, to operate properly. 2
Dok-Lok vehicle restraints can be hooked into 1 20 amp
branch circuit breaker per the 1999 National Electrical
Code Paragraph 430-53.
The VBR-300ALP & M Dok-Lok vehicle restraints require
120V, single phase, 60 Hz power and 1 amp of current
to operate properly. 10 Dok-Lok vehicle restraints can be
hooked into 1 20 amp branch circuit breaker per the 1999
National Electrical Code Paragraph 430-53.
NOTICE
All components must be connected to a SAFETY
EARTH GROUND where indicated. The SAFETY
EARTH GROUND must conform to the 1999 National
Electric Code Section 250-50 section (a) or section (c)
for a grounding electrode system.
When in doubt, call your Rite-Hite representative or
Rite-Hite at [phone].
The DOK-LOK vehicle restraint assembly includes a
control box with lights and the outside signal light box. The
VBR-300 Dok-Lok vehicle restraint assembly also includes
a hydraulic power unit. The outside junction box, conduit
ttings and wire are provided by others. Refer to Figure
13, page 10 for component location information. Refer to
electrical schematics found inside the control box for wiring
information.
Control Box Installation Guidelines -
Temperature Controlled Applications.
(All Models)
a. Conduit should be routed to enter through the bottom
or side of the enclosure. A drip leg may be needed if the
conduit could ll with water.
b. Seal the conduit in any location where the conduit
transitions temperature zones that may produce
condensation.
NOTICE
Failure to properly seal incoming conduit negates the
NEMA 4X rating of the control box and may result in
component failure due to water damage.
c. Spacers should be installed between the enclosure and
the wall to provide temperature insulation and air ow.
Fill and Bleed Hydraulic System
(VBR-300 Only)
1. Fill reservoir using supplied hydraulic fluid.
2. Press and hold the DIAGNOSTIC button inside
the control box until horn chirps (approximately 5
seconds). See Figure 12. Press Horn Override/#2
button (horn will chirp). System is now in Fill Mode.
Holding the LOCK or UNLOCK button will run the
pump up or down.
J2
J7
VR1
J13
J14
J16
J17 J3J4
TERM1
J1
RESET
J12
J15
J11
J5 JP2
LD24
UN-LK PB
LD26
LK PB
LD28
PB1
LD27
PB2
LD25
PB3
LD31
E-STOP
LD33
LOWER PB
LD34
LIP-OUT PB
LD17
PB1
LD19
PB1
LD35
RAISE PB
LD9
CR1
LD23
LD21
LD22
LD30
LD29
LD32
LD20
LD7LD8
LD1
LD2
LD6
LD4
LD3
LD50
LD52
LD36
LD15
LD16
LD14
LD12
LD18
LD13
LD11
LD39
LD20
LD40
LD37
LD42
LD48
LD10
LD49
LD46
LD44
LD43
LD41
LD38
SW1
SW2
PED-VU EN
PED-VU DET
OHD ITL
UNLK ITL
ARTD
LK
SOL2
SPARE
UNLK
PB PRESS
OVLD LOK
INSLT ITC
OSLT ITC
CTRL PWR
KYD HRN OVRD
UD ITC IN
STOP
SOL1SPARE
OSR
OSG
PED-VU AMB
PED-VU ALRM
LVLR-VU GRN
LVLR-VU RD
CRNR-VU GRN
CRNR-VU RED
GLT ITL
MWL ALARM
MWL ACTR
LVLR CONTR
SOL3
UNIDOX ITC
HORN
JP1 JP3
TERM 2
J8
K1
K2
CR2
μSD
CR1
CR2
LO/L
LO/L
RO/L
LO/L
DIAG
SW4
SW2
SW6 SW5
SW7
SW3
12345678
J10
J9
LD5
LD51
SW1
FACTORY JUMPER MUST BE IN PLACE
FACTORY JUMPER MUST BE IN PLACE
DIAGNOSTIC
BUTTON
J13-1
J13-2
J13-3
J13-4
J13-5
J13-6
J14-1
J14-2
J14-3
14-4
14-5
J16-1
J16-2
J16-3
J16-4
J16-5
J16-6
J17-1
J17-2
J12-6
J12-5
J12-4
J12-3
J12-2
J12-1
J15-5
J15-4
J15-3
J15-2
J15-1
N.O.
COM
N.C.
N.O.
COM
N.C.
J11-2
J11-1
FIGURE 12 - DIAGNOSTIC BUTTON
3. Cycle the Dok-Lok vehicle restraint up and down to
remove air from the system. Add remaining hydraulic
fluid. Stop cycling once the barrier travels the full
length of the track without hesitation.
4. Press DIAGNOSTIC button inside control box to exit
FILL mode.
5. Exit FILL MODE using one of the following steps:
• Press DIAGNOSTIC button
• Do not press any buttons for 5 minutes
• Cycle POWER
INSTALLATION

VBR-300 • VBR-300M • VBR-300ALP Dok-Lok®Installation Manual Rite-Hite®
10 Publication: AMEN00120 2017-09-19
NOTE:
a. Some docks may have dock/truck seals (or shelters)
installed or planned which are larger than standard.
Outside light, sign location, and mounting should be
studied before proceeding to avoid interference. See
Figure 13.
b. If required for special reasons, signs may be trimmed
for t. NEVER cut or eliminate sign letters/words. See
Figure 13.
c. Attach signs with concrete anchors or screws. Nails
are not acceptable. See Figure 13.
d. NEVER put conduit in front of signs. A clear view of
both exterior signs and the single interior sign must be
maintained at all times. See Figure 13.
e. Secure R.I.G. sensor wire to wall. Make sure wire is
secured so barrier can travel the full length of the track.
Install Signs (All Models)
There are 2 driver warning signs and 1 inside operator sign
supplied with each Dok-Lok vehicle restraint. Because of
the many ways signs can be mounted, hardware is not
supplied. Mount both outside signs on the right hand side
of the Dok-Lok vehicle restraint. The mirror-image sign is
usually mounted above the lower sign and near the outside
signal lights. (Mirror-image permits the truck driver to read
sign from truck mirror.) Mount the inside sign next to the
control box. All signs must be installed.
VBR-300
Dok-Lok
Shown
58”
15”
Hoses
Sensor
Wire
Clamp
Hydraulic
Power Unit
24”
Max.
48”
18”
Hoses
Outside Sign
Outside Sign
(Mirror Image)
Junction Box
Mounted On
Dock Face
Not To Extend
Out More Than 3”
48”
80”
96”
Approach
Outside Light
Inside Sign
Control Box
Edge Of Door Opening
4” Thick
Bumpers
15”
FIGURE 13 - SUGGESTED COMPONENT LOCATION
INSTALLATION

Rite-Hite®Installation Manual VBR-300 • VBR-300M • VBR-300ALP Dok-Lok®
Publication: AMEN00120 2017-09-19 11
Verify Components and Assembly
Make sure that all required components are present,
assembled and installed per all gures in this section.
Additionally, components should be assembled and
installed per associated Applications, guidelines and sales
order documentation.
Lubricate and Adjust
Perform initial lubrication and adjustments per the "180
days" maintenance instructions in the associated Restraint
Owner's Manual.
Operating Test (All Models)
Follow Operating Procedure in owners manual.
INSTALLATION

RITEHITE.COM12 www.ritehite.com Publication: AMEN00120 2017-09-19
GLOBAL SALES & SERVICE Representatives in All Major Cities
RITE-HITE WORLD HEADQUARTERS
8900 N. Arbon Drive
P.O. Box 245020
Milwaukee, Wisconsin 53224
RITE-HITE CHINA
First Floor, Building #3,
558 Tongxie Road,
Changning District
Shanghai 200335, China
RITE-HITE LATIN AMERICA
Alameda Lorena, 800 - Conj. 401/402
- Jardim Paulista
São Paulo/SP, CEP 01424- Brazil
RITE-HITE GMBH
Carl-Zeiss-Strasse 3
34471 Volkmarsen, Germany
414-355-2600
U.S. Only: 1-800-456-0600
[phone]-55-11-3527-9590 [phone]
LIMITED PRODUCT WARRANTY VBR-300 • VBR-300M • VBR-300ALP Dok-Lok®
Rite-Hite Company, LLC and its affiliates (collectively "Rite-Hite") warrant that the Product sold to the Owner will be
free of defects in design, materials and workmanship (ordinary wear and tear excepted) for the periods set forth below
("Limited Warranty").
One (1) Year(s) on all mechanical and electrical parts (non-prorated).
One (1) Year(s) labor, based on approved travel and labor repair times.
REMEDIES
Parts: Rite-Hite's obligations under this Limited Warranty are limited to repairing or replacing, at Rite-Hite's option, any
part which is determined by Rite-Hite to be defective during the applicable warranty period. Such repair or replacement
shall be Rite-Hite's sole obligation and the Owner's exclusive remedy under this Limited Warranty.
Labor: Rite-Hite will provide warranty service without charge for labor per the specified warranty period. Thereafter, a
charge will apply to any repair or replacement under this Limited Warranty.
CLAIMS Claims under this Limited Warranty must be made (i) within 30 (thirty) days after discovery and (ii) prior to
expiration of the applicable warranty period. Warranty period commences on the date of shipment. Claims shall be made
in writing or by contacting the representative from whom the Product was purchased directly. Owner must allow Rite-Hite
or its agent, a reasonable opportunity to inspect any Product claimed to be defective and shall, at Rite-Hite's option, either
(x) grant Rite-Hite or its agent access to Owner's premises for the purpose of repairing or replacing the Product or (y)
return of the Product to the Rite-Hite, F.O.B. Rite-Hite's factory.
NOT WARRANTED Rite-Hite does not warrant against and is not responsible for wear items such as fuses, batteries,
bulbs, vision and seals. No implied warranty shall be deemed to cover damages that result directly or indirectly from: (i)
the unauthorized modification or repair of the Product, (ii) damage due to misuse, neglect, accident, failure to provide
necessary maintenance, or normal wear and tear of the Product, (iii) failure to follow Rite-Hite's instructions for installation,
failure to operate the Product within the Product's rated capacities and/or specified design parameters, or failure to
properly maintain the Product, (iv) use of the Product in a manner that is inconsistent with Rite-Hite's guidelines or local
building codes, (v) movement, settling, distortion, or collapse of the ground, or of improvements to which the Products are
affixed, (vi) fire, flood, earthquake, elements of nature or acts of God, riots, civil disorder, war, or any other cause beyond
the reasonable control of Rite-Hite, (vii) improper handling, storage, abuse, or neglect of the Product by Owner or by any
third party.
DISCLAIMERS THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER REPRESENTATIONS AND
WARRANTIES, EXPRESS OR IMPLIED, AND RITE-HITE EXPRESSLY DISCLAIMS AND EXCLUDES ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PURPOSE. RITE-HITE SHALL NOT BE SUBJECT TO ANY
OTHER OBLIGATIONS OR LIABILITIES, WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT
(INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORIES OF LAW, WITH RESPECT TO THE
PRODUCTS SOLD OR SERVICES RENDERED BY RITE-HITE, OR ANY UNDERTAKINGS, ACTS, OR OMISSIONS
RELATING THERETO.
LIMITATION OF LIABILITY IN NO EVENT SHALL RITE-HITE BE RESPONSIBLE FOR, OR LIABLE TO ANYONE
FOR, SPECIAL, INDIRECT, COLLATERAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF
RITE-HITE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Such excluded damages include, but
are not limited to, personal injury, damage to property, loss of goodwill, loss of profits, loss of use, cost of cover with any
substitute product, interruption of business, or other similar indirect financial loss.
170714