Soundoff Signal mpower PMP2RS 02 Series User manual

1
1.800.338.7337 / www.soundo󰀨signal.com
mPOWER Spoiler BRKT_Utility 2020+ English 0820
2020 FORD UTILITY SPOILER BRACKET
PMP2RSX02 - For use with mpower fascia Stud Mount Light
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat build-up and
re. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle Owner’s
Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
conguration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal or local
chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING
FEATURES:
• Warning arrow greatly reduces install time through use of 3-wire
technology
• Functionality mimics the rear of a lightbar
• Integrates under the spoiler of the vehicle for a seamless look
• Available in single, dual or tricolor
PART NUMBERS:
• PMP2RS102: Rear Spoiler Bracket, 1 Module Kit, Black, for use with
mpower® 4” Fascia Stud Mount Light - Ford Utility 2020
• PMP2RS202: Rear Spoiler Bracket, 2 Module Kit, Black, for use
with mpower® 4” Fascia Stud Mount, 3-Wire 4” Stud Mount Light &
mpower Arrow Kit Light - Ford Utility 2020
• PMP2RS302: Rear Spoiler Bracket, 3 Module Kit, Black, for use
with mpower® 4” Fascia Stud Mount, 3-Wire 4” Stud Mount Light &
mpower Arrow Kit Light - Ford Utility 2020
• PMP2RS402: Rear Spoiler Bracket, 4 Module Kit, Black, for use
with mpower® 4” Fascia Stud Mount, 3-Wire 4” Stud Mount Light &
mpower Arrow Kit Light - Ford Utility 2020
COMPONENT
QUANTITY
PMP2RS102 PMP2RS202 PMP2RS302 PMP2RS402
2020 Ford Utility Left Bracket 1 1 1 1
2020 Ford Utility Right Bracket 1 1 1 1
6-32 Rubber Insert 4 4 6 6
6-32 X 1.00” Torx Screw 4 4 6 6
Installation Instruction Sheet 1 1 1 1
Product Warning Card 1 1 1 1
4 MODULE
3 MODULE
2 MODULE
1 MODULE
DRIVER’S SIDE SHOWN

2
1.800.338.7337 / www.soundo󰀨signal.com
mPOWER Spoiler BRKT_Utility 2020+ English 0820
2020 FORD UTILITY SPOILER BRACKET
PMP2RSX02 - For use with mpower fascia Stud Mount Light
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
Fig. 2
INSTALLATION:
1. Remove rear spoiler from the vehicle using the
manufacturer’s recommended method. Lay the
included drill template onto the driver’s side of the
spoiler, as shown in Fig. 1. Line up the template
with the seam on the outer edge of the spoiler to
properly position it.
2. Secure the template in place with non-marking
tape.
3. Refer to the chart below and to the included
template for drill instructions:
4. Scribe the drill locations indicated by the template,
remove the template, and drill, as shown in Fig. 2.
5. Flip the drill template over and lay on passenger’s
side. Temporarily, secure in place with non-
marking tape. Scribe the drill locations indicated
by the template.
6. Remove the template and drill as indicated.
7. Attach the lights to the included brackets, as
shown in Fig. 3. Secure nuts 1/8” turn past seated
contact.
8. Press the 6-32 rubber inserts into the spoiler. Then
place the bracket, as shown in Fig. 4. Route wires
through the wire pass through hole. Secure with
screws supplied. Repeat for opposite side.
Fig. 3 Fig. 4
Ifacongured,mpower® ArrowKitwas
purchased,skiptoStep8.
5/16” drill through
rst wall of spoiler for
rubber inserts, number
of holes is dependent
on number
of modules
3/4” drill through rst wall of
spoiler for wire pass through
Fig. 1
DRILL TEMPLATE
BRACKET TYPE MOUNTING HOLES
1 MODULE C, E
2 MODULE B, D
3 MODULE A, B, D
4 MODULE F, G, H
4 MODULE VERSION SHOWN
4 MODULE VERSION SHOWN
4 MODULE VERSION SHOWN

3
1.800.338.7337 / www.soundo󰀨signal.com
mPOWER Spoiler BRKT_Utility 2020+ English 0820
2020 FORD UTILITY SPOILER BRACKET
PMP2RSX02 - For use with mpower fascia Stud Mount Light
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
INSTALLATION(cont.):
9. Drill 1-3/8” hole in hatch sheet metal as shown in
Fig. 5.
10. Insert grommet into hole, as shown in Fig 6.
11. Run wire through grommet and make nal
connections, as shown in Fig. 7.
12. Before re-installing the rear spoiler, make all
electrical connections. Refer to the mpower arrow
kit instruction sheets for details.
BEFORERE-INSTALLINGTHEREARSPOILER,
MAKEALLELECTRICALCONNECTIONS.
REFER TO THE MPOWER®ARROWKIT
INSTRUCTIONSHEETS*.
*IF USING THE 5-WIRE MPOWER® FASCIA LIGHTS,
REFER TO:
WWW.SOUNDOFFSIGNAL.COM/IS/MPOWER
Step 12
Fig. 5 Fig. 6
Fig. 7