Robe Anolis Divine 160 RGBW/RGBA/PW/TW User manual

Version
2
.
5
QR code for user manual

Divine 160
2
Table of contents
1. Safety instructions ...................................................................................................................................................... 3
2. Fixture exterior view ................................................................................................................................................... 5
3. Installation .................................................................................................................................................................. 6
3.1 Connection to the mains ...................................................................................................................................... 6
3.2 Mounting the fixture ............................................................................................................................................ 8
3.3 Top hat and half top hat installation .................................................................................................................... 9
3.4 Barn door and Wire guard/anti-glare installation ............................................................................................... 9
4. Divine 160 - DMX protocols ..................................................................................................................................... 10
4.1 RGBW/RGBA version .......................................................................................................................................... 10
4.2 TW version .......................................................................................................................................................... 13
4.3 PW version .......................................................................................................................................................... 15
5. Control menu ............................................................................................................................................................ 16
5.1 Fixture Address ................................................................................................................................................... 16
5.2 Fixture information ............................................................................................................................................. 16
5.3 Personality .......................................................................................................................................................... 17
5.4 Manual mode ...................................................................................................................................................... 19
5. 5 Test sequences................................................................................................................................................... 20
5.6 Stand-alone setting ............................................................................................................................................. 20
5.7 Special functions ................................................................................................................................................. 21
6. Technical specifications ............................................................................................................................................ 23
7. Cleaning and maintenance ....................................................................................................................................... 25
7.1 Replacing a fuse .................................................................................................................................................. 25
7.2 Disposing of the product .................................................................................................................................... 25

Divine 160
3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR Divine 160!
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure
safe operation, it is absolutely necessary for the user to follow the safety instructions and warnings written in this
manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual
or any unauthorized modification to the device.
Unauthorized modification will void warranty.
This device is for professional use only. It is not for household use.
Warning for fixtures with Harsh Environment Finish (HEF):
Handle with care!
Avoid any damage to the painted surface.
Damaging the paint may result in corrosion and loss of warranty.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!
Make sure that the available voltage is not higher than stated on the rear side of the fixture.
This fixture should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized distributor or local power company.
Always disconnect the fixture from AC power before servicing or cleaning internally.
Do not overload supply line as this can result in fire or electric shock.
Make sure the power/data cable is never crimped or damaged by sharp edges. Check the fixture and the
power/data cable from time to time.
Do not install the unit near an open flame.
Refer servicing to qualified service personnel.
This fixture falls under protection class I. Therefore, this fixture has to be connected to a mains socket outlet
with a protective earthing connection.
Do not connect this fixture to a dimmer pack.

Divine 160
4
Warning!
LED light emission. Risk of eye injury.
Do not look straight at the fixture´s LEDs during operation. The intense light beam may damage your eyes.
The light source contains blue LEDs.
Immunity of the equipment is designed for electromagnetic environments E1, E2, E3 according to the standard
EN55103-2 ed.2 Electromagnetic compatibility. Product family standard for audio, video, audiovisual and
entertainment lighting control apparatus for professional use. Part 2: Immunity.
The product (covers and cables) must not be exposed to a high frequency electromagnetic field higher than 3V/m.
The installation company should check levels of possible interferences above the tested levels E1,E2,E3 given by this
standard (e.g. transmitters in surrounding area) before installing the equipment.
Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility of multimedia
equipment – Emission Requirements according to class B.
Keep combustible materials at least 0.3 m away from the fixture.
If the fixture has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation of water might damage your device. Leave the device switched off until it
has reached room temperature.
Avoid brute force when installing or operating the fixture.
When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat or dust.
Avoid using the unit in locations subject to possible impacts.
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
Do not block the front glass cover with any object when the fixture is under operation.
The fixture body must never be covered with cloth or other materials.
The fixture becomes very hot during operation. Allow the fixture to cool approximately 30 minutes prior to
servicing or maintenance.
Operate the fixture only after having familiarized yoursef with its functions. Do not permit operation by persons
not qualified to operate the fixture. Most damages are the result of unprofessional operation!
Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons!
Please use the original packaging if the fixture is to be transported.
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the warranty becomes void. Furthermore, any other operation may lead to dangers like short-circuit,
burns, electric shock etc.

Divine 160
5
2. Fixture exterior view
Note: customer can interchange the cable glands and blind flanges in the fixture base to create a side or rear
connection.
1.
Head with LED array
2. Tilt lock
3. Base
4. Cable glands or blind flange (depends on fixture version)
5. Surface Mount adaptor
Side
connection shown
Rear connection shown

Divine 160
6
3. Installation
3.1 Connection to the mains
Fixtures must be installed by a qualified electrician in accordance with all national
and local electrical and construction codes and regulations.
This device falls under class one and must be grounded!
To connect the Divine 160 to mains and a DMX controller, use a 5-cored cable Flamar Li9YC11Y. The 3 cores serve
for the power supply and 2 shielded cores are intended for DMX connection:
Core
Connection
Core
Connection
Black
Live
(L)
Red
Data + (+)
White
Neutral
(N)
White
D
ata
–
(
-
)
Yellow/Green
GND
PE ( )
Shielding
Data ground (0)
1. Unscrew the eight screws (2) on the terminal block cover (1) to get access to the terminal block and
control display (6) with four control buttons (7).
2. Unscrew both cable glands (4) from the terminal block cover (1) and both blind flanges (10) from the
fixture base.
3. Apply an adequate layer of the paste LOCTITE 5331 on the plastic holder of the cable gland before
inserting it into the body of the gland. Apply an adequate layer of the paste LOCTITE 577 on the thread of
the gland body. Screw both cable glands (4) back into the terminal block cover (1) - see the picture below.
4. Apply an adequate layer of the paste LOCTITE 577 on the thread of the blind flange. Screw both blind
flanges (10) back into the fixture base.
5. Pass the power/data cable through one cable gland (4) and connect to the terminal block.
6. Remove end cap (3) from cable glands before passing cable into the terminal block compartment. The two
cable glands serve for cables of diameter of 4-8 mm.
To keep declared IP rating, every cable gland has to be covered with an end cap (3) if the cable gland is not
used for cable passing.

Divine 160
7
Note: If you are interchanging cable glands (4) and blind flanges (10), do not forget to apply LOCTITE 5331
and 577 on cable glands and LOCTITE 577 on blind flanges.
7. After connecting cables and setting the fixture by means of the control display and four buttons, place the
cover (1) on the terminal block back, make sure the seal (5) is inserted correctly.
8. Screw the terminal block cover (1) with eight screws using a tightening torque of 4 Nm.
9. Check that all cable glands and screws and blind flanges are firmly secured.
Rear connection shown
Side connection shown
Base technical features of the ABB terminal block:

Divine 160
8
Type: DS 2,5/10.4L (4 springs mini blocks)
Parameter
IEC
UL/
CSA
Rated voltage
800 V
600 V
Rated current
24 A
15 A
Wire size rated/gauge
2.5mm
2
/A2
12AWG
Wire stripping length
9.5 mm
3.2 Mounting the fixture
The Divine 160 can be arranged in any position/orientation without altering its operation characteristics. The LED
module can be tilted to desired position by means of the tilt lock. Use an Allen key 6 to adjust desired tilt position.
Screw the surface mount adaptor (11) to the base of the fixture by means of the six screws M8x20 (8).
Four slots (9) in the surface mounting adapter serve for mounting on a non-flammable flat surface via four
screws.
Ensure that the structure to which you are attaching
the fixture is secure.
Caution: Overhead installation requires experience. Fixtures may cause severe injuries when crashing down! If you
have doubts concerning the safety of a possible installation, do not install the device and consult installation with
an expert.

Divine 160
9
3.3 Top hat and half top hat installation
Half top hat Top hat
1. Unscrew screws M3x5 (3) to remove the bottom part (2) of the top hat (half top hat).
2. Place the upper part (1) of the top hat (half top hat) on the fixture head and secure it by means of two
screws M5x8 (4) with spring washers to the two threaded holes (A) on the back side of the fixture head.
3. Place the bottom part (2) of the top hat (half top hat) on the bottom part of the fixture head and screw it
back to the upper part (1) of the top hat (half top hat) by means of the screws M3x5 (3).
4. Secure the bottom part of the top hat (half top hat) to the fixture head by means of two screws M5x8 (4)
with spring washers to the two threaded holes (A) on the back side of the fixture head.
3.4 Barn door and Wire guard/anti-glare installation
Barn door Wire guard/anti-glare
1. Unscrew screws M3x5 (3) to remove the bottom part (2) of the barn door (wire guard/anti-glare).
2. Place the upper part (1) of the barn door (wire guard/anti-glare) on the fixture head and secure it by means
of two screws M5x10 (4) /M5x8 for wire guard/anti-glare/ with spring washers to the two threaded holes
(A) on the back side of the fixture head.
3. Place the bottom part (2) of the barn door (wire guard/anti-glare) on the bottom part of the fixture head
and screw it back to the upper part (1) of the barn door (wire guard/anti-glare) by means of the screws
M3x5 (3).
4. Secure the bottom part of the barn door (wire guard/anti-glare) to the fixture head by means of two
screws M5x10 (4) /M5x8 for wire guard/anti-glare/ with spring washers to the two threaded holes (A) on
the back side of the fixture head.

Divine 160
10
4. Divine 160 - DMX protocols
4.1 RGBW/RGBA version
Version 1.4
Mode 1
Channel
Mode 2*
Channel
Mode 3
Channel
Mode 4
Channel
Value Function Type of
control
1 1 - -
0-19
20-24
25-29
30-39
40-49
50-59
60-69
70-89
90-99
100-109
110-119
120-129
130-255
Special functions
Reserved (0=default)
To activate following functions , stop in DMX value
for at least 3 sec.
Corresponding menu items are temporily overrided.
Display On
Display Off
RGBW(RGBA) colour mixing mode
CMY colour mixing mode
Colour calibration mode On
Colour calibration mode Off
Reserved
Dimmer curve: linear
Dimmer curve: square law
White count On
White count Off
Reserved
step
step
step
step
step
step
step
step
step
step
2
- 1 1
0-255
Red – all zones
Red LEDs saturation control (0-100%) (255=default) proportional
3
- 2 2
0-255
Green – all zones
Green LEDs saturation control (0-100%) (255=default) proportional
4
- 3 3
0-255
Blue – all zones
Blue LEDs saturation control (0-100%) (255=default) proportional
5
- 4 4
0-255
White (Amber) – all zones
LEDs saturation control (0-100%) (255=default) proportional
-
2 - -
0-255
Red - zone 1
Red LEDs saturation control (0-100%) (255=default) proportional
-
3 - -
0-255
Green - zone 1
Green LEDs saturation control (0-100%) (255=default) proportional
-
4 - -
0-255
Blue - zone 1
Blue LEDs saturation control (0-100%) (255=default) proportional
-
5 - -
0-255
White (Amber) - zone 1
LEDs saturation control (0-100%) (255=default) proportional
-
6 - -
0-255
Red zone 2
Red LEDs saturation control (0-100%) (255=default) proportional
-
7 - -
0-255
Green - zone 2
Green LEDs saturation control (0-100%) (255=default) proportional
-
8 - -
0-255
Blue - zone 2
Blue LEDs saturation control (0-100%) (255=default) proportional
-
9 - -
0-255
White (Amber) - zone 2
LEDs saturation control (0-100%) (255=default) proportional
-
10 - -
0-255
Red - zone 3
Red LEDs saturation control (0-100%) (255=default) proportional