Robe ROBIN LEDBeam 350 RGBA User manual

1
Version 1.6

2
Table of contents
1. Safety instructions ......................................................................................................... 3
2. Fixture exterior view ...................................................................................................... 5
3. Installation....................................................................................................................... 6
3.1 Connection to the mains ............................................................................................ 6
3.2 Rigging the xture ...................................................................................................... 7
3.3 Eggcrate installation................................................................................................... 9
3.4 Di󰀨usion lter installation (LEDBeam 350 only) ...................................................... 10
3.5 DMX-512 connection................................................................................................ 11
3.6 Ethernet connection (EP version only)..................................................................... 12
3.7. Wireless DMX operation ......................................................................................... 13
4. Control menu map........................................................................................................ 14
5. Control menu ............................................................................................................... 17
5.1 Addressing (DMXA).................................................................................................. 17
5.2 Fixture information (Info) .......................................................................................... 17
5.3 Personality (Pers)..................................................................................................... 18
5.4 Manual Control (Manual).......................................................................................... 20
5.5 Test program (Test Prg)............................................................................................ 20
5.6 Stand-alone (St Alone) ............................................................................................. 20
5.7 Reset........................................................................................................................ 21
5.8 Special functions (Special)....................................................................................... 21
6. RDM ............................................................................................................................... 23
7. Error and information messages ................................................................................ 24
8. Technical Specications.............................................................................................. 25
9. Maintenance and cleaning........................................................................................... 27
9.1 Replacing fuse ......................................................................................................... 27
10. Photometric diagrams................................................................................................ 28
11. ChangeLog ................................................................................................................. 32
ROBIN LEDBeam 350 RGBA
ROBIN LEDBeam 350 FW RGBA
ROBIN LEDBeam 350 RGBA EP
ROBIN LEDBeam 350 FW RGBA EP

3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR ROBIN LEDBeam 350 !
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to en-
sure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this ma-
nual or any unauthorized modication to the device.
Please consider that damages caused by manual modications to the device are not subject to warranty.
The ROBIN LEDBeam 350 was designed for indoor use and it is intended for
professional application only. It is not for household use.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!
Make sure that the available voltage is not higher than stated on the rear panel of the xture.
This xture should be operated only from the type of power source indicated on the marking label. If you are
not sure of the type of power supplied, consult your authorized distributor or local power company.
Always disconnect the xture from AC power before cleaning, removing or installing any part of the xture.
The power plug has to be accessible after installing the xture. Do not overload wall outlets and extension cords
as this can result in re or electric shock.
Do not allow anything to rest on the power cord. Do not locate this xture where the cord may be damaged by
persons walking on it.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture and the power
cord from time to time.
Refer servicing to qualied service personnel.
This xture falls under protection class I. Therefore this xture has to be connected to
a mains socket outlet with a protective earthing connection.
Do not connect this xture to a dimmer pack.
Warning! Risk Group 2 LED product according to EN 62471.
LED light emission. Risk of eye injury. Do not look into the beam at short distance of
the of the product.
Do not view the light output with optical instruments or any device that may
conncentrate the beam.
The light source contains blue LEDs.
If the xture has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched o󰀨 until
it has reached room temperature.
Avoid brute force when installing or operating the xture.

4
This xture was designed for indoor use only, do not expose this unit to rain or use near water.
When choosing the installation spot, please make sure that the xture is not exposed to extreme heat, moisture
or dust.
Do not block the lens array with any object when the xture is under operation.
The cooling openings in head and base of the xture should never be covered with cloth or other materials,
and never must be blocked.
This xture should not be placed in a built-in installation unless proper ventilation is provided.
Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fastened.
Always use a secondary safety wire for overhead installation of the xture.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xture.
The xture becomes hot during operation. Allow the xture to cool approximately 15 minutes prior to manipu-
late with it.
To avoid damage of an internal optical system of the xture, never let the sunlight (or
other light source) lights directly to the lens array, even when the xture is not working
Operate the xture only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the xture. Most damages are the result of unprofessional operation!
Please use the original packaging if the xture is to be transported.
Please consider that unauthorized modications on the xture are forbidden due to safety reasons!
If this device will be operated in any way di󰀨erent to the one described in this manual, the product may su󰀨er
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-
-circuit, burns, electric shock, crash etc.
Potential foggy front lens array does not inuence function of the xture and does not
subject to complaint.
Immunity of the equipment is designed for electromagnetic environments E1, E2, E3 according to the stand-
ard EN55103-2 ed.2 Electromagnetic compatibility. Product family standard for audio, video, audiovisual and
entertainment lighting control apparatus for professional use. Part 2: Immunity.
The product (covers and cables) must not be exposed to a high frequency electromagnetic eld higher than 3V/m.
The installation company should check levels of possible interferences above the tested levels E1,E2,E3 given
by this standard (e.g. transmitters in surrounding area) before installing the equipment.
Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility of multimedia
equipment – Emission Requirements according to class B.

5
2. Fixture exterior view
10 - Top head cover
11 - Rear Head cover
12 - Handle
13 - DMX Out (5-pin XLR)
14 - DMX In (5-pin XLR)
15 - Fuse holder
16 - Power In (PowerCon True 1)
17 - Power Out (PowerCon True 1)
1 - Lens array
2 - Arm
3 - Display
4 - Escape button
5 - Enter button
6 - Next button
7 - Preview button
8 - Base
9 - Tilt lock
EP version only
18 - Ethernet In
19 - Ethernet Out