Robert Juliat ARTHUR 1014TC User manual

LED FOLLOWSPOT
VALIDATION: 06/04/22
DN41195900-A
ARTHUR
Quick Start Guide
Robert Juliat S.A.S. 32, rue de Beaumont, F 60530 Fresnoy-en-Thelle - phone : [phone] - fax : [phone] - [email protected]
www.robertjuliat.com
User's manual: Included:
For more information and updates:
www.robertjuliat.com/followspots/followspots.html
CAL03 OR CAL04
SGUP2
x6
VDM120
PF1013
CCU1
V1
DN41195900
Quick
Start
Guide
800 W FOLLOWSPOTS
1014TC / 1014TCLT TOP CONTROL
1014 / 1014LT
Model Standard North American
5.5° – 15° ARTHUR 1014 ARTHUR 1014C
4° – 10° ARTHUR 1014LT ARTHUR 1014CLT
Model Standard North American
5.5° – 15° ARTHUR 1014TC ARTHUR 1014CTC
4° – 10° ARTHUR 1014TCLT ARTHUR 1014CTCLT

ENEN
Group risk 2. Luminaires should be positioned so that prolonged
staring into luminaire at a distance closer than 50m is not expected.
EN - 2 -
GT4000
Please refer to the relevant user manual for further details.
GENERAL INSTRUCTIONS
1. Not for residential use.
2. These fixtures must only be serviced by a qualified technician.
3. In addition to the instructions indicated on this page, relevant health and safety requirements of the appropriate EU
Directives must be adhered to at all times.
4. This fixture is in compliance with section 17 - Lighting appliance for theatre stages, television, cinema and photograph
studios. Standards NF EN 60598-1, NF EN 60598-2-17, Low Voltage Directive 2014/35/UE & EMC Directive 2014/30/UE.
5. This fixture is rated as IP20, and is for indoor use only.
FIXTURE
6. Ensure fixture is correctly mounted on an appropriate support.
7. Protection screens and lenses must be replaced in the event of any damage, such as cracks or deep scratches, since
these might reduce performance.
8. When hung or flown the fixture must be secured by an additional hanging accessory (such as a safety cable or bond) of
suitable length.
9. Safety bonds or cables must be securely attached to the back of the fixture and be as short as possible, or
rolled up as necessary, to minimise travel distance should the fixture be dislodged.
10. Movable accessories (scroller, etc.) must also be secured with a suitable safety cable or bond at the front of the fixture.
11. The combined weight of both the fixture and the accessories must be considered when choosing the load-bearing
capability of safety cable or bond.
12. Do not open lighting fixture when the source is on.
13. WARNING: LED source become hot during use. Allow fixture to cool before servicing.
14. Do not tamper with design of fixture nor any of its safety features.
15. Tighten electrical mains cable connections regularly and replace with one of identical specification if damaged.
16. Use only with correct power supply.
VENTILATION
17. Keep well away from flammable material.
18. Not for outdoor use. Do not cover. Do not permit fixture to get wet.
19. To avoid overheating, do not obstruct air vents.
20. Ensure any cooling fans are in correct working order. If fans are not working, turn fixture off immediately and service as
necessary.
CLEANING
21. Do not touch the LED source with your fingers.
22. To clean the optical parts, use a soft cloth in combination with distilled water or isopropyl alcohol recommended for coated optics.
Do not use any cleaning product that contains solvents or abrasives, as these can cause surface damage. Dry with a soft lint-free cloth.
23. Regularly remove dust with a soft lint-free cloth.
24. If the fixture has filters, they must be cleaned frequently.
POWER SUPPLY
25. Disconnect from the mains before servicing.
26. Mains connection only. Do not connect to "electronic output" such as dimmer.
27. Ensure power supply circuit breakers, always remain accessible.
PLEASE NOTE
This product has been built to conform to European standards relating to professional lighting equipment. Any modification
made to our products will void the manufacturers' warranty.
1 User’s instructions
2 Installation
Risk group 2
CAUTION: Possibly hazardous optical
radiation emitted from this product.
Do not stare at operating lamp.
Maybe harmful to the eye.
Dimensions in mm

EN
9
7
5
3
11
13
21
110
8
6
4* 5*
12
2
EN - 3 -
4 Electrical / Data connections
1
2345 67
Functions
1 Yoke
2 Tilt locking handle
3 Side operating handle
4 Iris control (1014/1014LT only)
4* Iris control (1014TC/1014TCLT only)
5 Dimming control (1014/1014LT only)
5* Dimming control (1014TC/1014TCLT only)
6 Colour changer
7 Zoom adjustment
8 Focus adjustment
9 Frost glass
10 Spare filter
11 Gobo holder
12 Local display
13 Keypad
14 Identification plate
15 Data connectors (OUT and IN)
16 Power connectors (IN and OUT)
17 Power switch (thermal breaker)
18 USB connectors for accessories
19 RJ45 connectors
20 Cable lock
21 Handles
22 Lifting rings
23 Tilt stopper
1 Switch Power ON / OFF - Thermal breaker (10A. automatic switch)
2 Power input
Connector: Neutrik®powerCON TRUE1 TOP Max. 16A.
Power input: 100 => 240V 50/60Hz
Power consumption:
@ 230V 50Hz = 990VA/960W
@ 120V 60Hz = 1050VA/1030W
@ 100V 60Hz = 1080VA/1060W
3 Power output
Connector: Neutrik®powerCON TRUE1 TOP Max. 8A.
Power output available:
@ 230V/16A = max 2600VA (or 2 Arthur units)
@ 120V/15A = max 700VA (or 0 Arthur unit)
4 Data In Connector: XLR 5-pin / Protocol: USITT DMX 512-A RDM
5 Data Out Connector: XLR 5-pin
6 Ethernet Connectors: RJ45 / Protocol Art-Net, sACN + software updating
7 Auxiliary out Connectors: USB (Not for charging purpose)
4
17
19 15 18
14
20
16
22
23

EN
ZOOMFOCUS
AB
ZOOMFOCUS
AB
A
B
A
B
(1014TC & 1014TCLT)
(1014 & 1014LT)
(1014 & 1014LT)
(1014TC & 1014TCLT)
EN - 4 -
5 Operation
Step 1 - Switch on the followspot by pressing the ON / OFF power button.
0% 100% closed iris
Robert Juliat reserves the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.
Step 2 - Open the colour changer unit to let the light beam out.
Step 4 - The light beam zoom and focus can be set by using the control knobs A & B
Step 5 -The beam size can be adjusted by using the iris cassette.
Step 3 - Use the manual dimming control to adjust the light intensity.