ROBERTO FIORE Cabinets To Go OC3390SD User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Pantry Cabinets
ITEM No.:OC3390SD
Page 1

►Items Quantity
Item Description Qty
Doors 2
B
Back Panel 1
C Side Panels Left & Right
2
D Top, Bottom, & Center Panels
4
E Drawer Fronts 3
F
Toe Kick
1
G
Hardware Box
3
Hinges 4pcs, Bumpers 16pcs, 2/3" Flat Head Screws 8pcs, 2/3" Round Head Coarse Thread Screws 16pcs, Cam Locks 42pcs, Wooden Dowels 28pcs, Drawer Glides 3pc, Shelf Clips 4pc
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b e
Qty 42
f
Qty 28
cd
Qty 4 Q ty 16 Qty 8Qty 16
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
A
C
B
F
E
A
g
Qty 3
C
D
A
D
D
D
E
E
G
H
I
Drawer Box
Braces
2
H
I
h
Qty 4
1
Shelf

Page 3
►Instructions:
1.Unpack box & identify pieces on Page 2. Place
side panel (C) onto a soft work surface.
(Figure 1)
2.Install Hinge base plates (a) & drawer glides (g)
onto side panel into designated holes using
screws (d). (Figure 2)
3.Install metal male cam locks (e) into designated
holes on side panel (C), braces (H), and top/
center/bottom panels (D). Use screwdriver to
tighten. Install the wooden dowels
(f) into designated holes. (Figure 3)
4.Install the toe kick (F) onto bottom panel (D).
(Figure 3)
5.Install Top/Center/Bottom Panels (D) onto the
right side panel (C). (Figure 3)
6.Install locking lugs (e) into designated holes, and
then lock them with a screwdriver. (Figure 4)
7.Install side panel (C) onto the assembled panels
using the same methods above. (Figure 5)
Figure 1
SoftSurface
Hard Surface
C
C
Figure 2 Base Plate
Figure 3
Figure 4
Figure 5
a
Qty 4
d
Qty 16
e
Qty 42
f
Qty 28
g
Qty 3
8.Assemble the drawer boxes. (Figure 6)
Figure 6

5.
6.
7.
9.Install hinges onto doors into designated holes using screws provided.
Page 4
c
Qty 8
b
Q ty 16
a
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive
cleaners containing acetone, chlorine or strong ble ach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances
should you use chrome cleaner on ch rome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.
h
Qty 4
Install doors onto cabinet sides though pre-marked screw holes.
Install the bumpers (b) onto the door corners opposite of the hinges.
Install the assembled drawer boxes into the drawer glides.
Install the shelf (I) using shelf pins (h).