Roberts Revival RD-60 User manual

DAB/FM RDS digital radio
model RD-60
Please read this manual before use
ROBERTS
Sound for Generations

Controls .......................................................................2-3
Battery operation ............................................................4
Using the AC adaptor .....................................................4
Operating your radio - DAB ............................................5
Selecting a station - DAB ...............................................6
Display modes - DAB .....................................................7
Finding new stations - DAB ............................................8
Secondary services - DAB .............................................8
Manual tuning - DAB ......................................................9
Signal strength display - DAB.........................................9
Dynamic range control (DRC) settings - DAB ..............10
Operating your radio - Search tuning - FM................... 11
Manual tuning - FM ......................................................12
Display modes - FM......................................................13
Favourite button ...........................................................14
Recalling your favourite station ....................................14
Preset stations DAB and FM ........................................15
FM stereo/mono ...........................................................16
Scan sensitivity - FM ....................................................17
Software version...........................................................18
Contents
System reset ................................................................19
Headphone socket .......................................................20
Auxiliary input socket....................................................20
Line output socket ........................................................21
Display backlight ..........................................................21
General.........................................................................22
Specifications ...............................................................22
Circuit features .............................................................22
Guarantee .......................................................Back page
1

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri) 2
Controls
1. Low battery indicator
2. Volume control
3. Headphone socket
4. Auxiliary Input socket
5. Telescopic aerial
(Top)
2
3
7910
5
12
11. Preset button
12. Tuning control
13. LCD display
8
13
611
4
1
6. Favourite button
7. On/Off button
8. FM/DAB button
9. Auto Tune button
10. Info button

3
Controls
14. DC in socket
15. Line output socket
15
14

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri) 4
Battery operation
1. Release the catch securing the rear door of your radio.
2. Insert four LR20 (D size) batteries into the spaces in the compartment.
Take care to ensure all batteries are inserted with the correct polarity
as shown inside the battery compartment. Close the rear door and
secure the catch.
3. The Low Battery indicator lighting, distortion, or the radio switching
itself off are all signs that the batteries may need replacing.
4. If the radio is not to be used for any extended period of time it is
recommended that the batteries are removed from the radio.
We would recommend for economy that the RD-60 is used via the
AC adaptor whenever possible with battery operation for occasional
or stand-by use only.
Using the AC adaptor
1. Insert the adaptor plug into the DC in socket on the rear of your
radio.
2. Plug the adaptor into a standard 13A mains socket outlet. Whenever
the adaptor is used the batteries are automatically disconnected.
The AC adaptor should be disconnected from the mains supply and
the radio when not in use.
• IMPORTANT: The mains adaptor is used as the means of connecting
the radio to the mains supply. The mains socket used
for the radio must remain accessible during normal use. In order
to disconnect the radio from the mains completely, the mains
adaptor should be removed from the mains socket outlet
completely.
1

5
2
Operating your radio - DAB
1. Carefully extend the telescopic aerial.
2. Press the On/Off button to switch on your radio. The display will show
"Welcome to DAB".
3. If this is the first time the radio is used a quick scan of the UK Band III
DAB channels will be carried out. If the radio has been used before
the last used station will be selected.
4. During the scanning process, the lower line of the display shows a
bar-graph indicating progress of the scan.
5. When the scanning is completed the first station (in numeric-alpha
order 0...9...A....Z) will be selected.
6. If the station list is still empty after the scan your radio will display "No
stations available".
7. If no signals are found it may be necessary to relocate your radio to
a position giving better reception. Then, either switch your radio off
and on again, or press the Auto Tune button to repeat the scan.

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri) 6
Selecting a station - DAB
1. The top line of the display shows the name of the station currently
selected.
2. Rotate the Tuning control to scroll through the list of available stations
on the lower line of the display. Stop rotating the Tuning control when
you find the station that you wish to hear.
3. Press and release the Tuning control to select the station.The display
may show "Now tuning..." while your radio finds the new station.
4. Adjust the Volume control to the required setting.
Note: If after selecting a station the display shows "Not Available" it may
be necessary to relocate your radio to a position giving better reception.
The use of radio station presets for selecting your preferred radio stations
is described on page 16.
2
4

7
1
Display modes - DAB
Your radio has seven display modes:-
1. Press the Info button to cycle through the various modes.
a. Scrolling text Displays scrolling text messages such as
artist/track name, phone in number etc.
b. Program Type Displays the type of station being listened
to e.g. Pop, Classic, News etc.
c. Multiplex Name Displays the name of DAB multiplex to
which the current station belongs.
d. Time and date Displays the current the time and date.
e. Frequency Displays the frequency of the DAB
multiplex for the station listened to.
f. Bit rate & audio type Displays the digital bit rate & audio type
for the station being listened to.
g. Signal Strength Displays a graph showing the signal
strength for the station being received.
a
b
c
d
f
e
g

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri) 8
Finding new radio stations - DAB
As time passes new stations may become available. To find new stations
proceed as follows:-
1. Press and release the Auto Tune button. The display will show
"Scanning..." and your radio will perform a scan of the UK DAB
frequencies. As new radio stations are found the station counter on
the right-hand side of the display will increase and the radio stations
will be added to the list stored in the radio.
2. To carry out a full scan of the entire DAB Band III frequencies press
and hold down the Auto Tune button for more than 2 seconds and
then release. The display will show "Full Scanning...". As new radio
stations are found the station counter on the right-hand side of the
display will increase and the radio stations will be added to the list
stored in the radio.
1
2
Secondary services - DAB
1. Certain radio stations have one or more secondary services associated
with them. If a radio station has a secondary service associated with it
the display will show ">>" next to the station name on the station list.
The secondary service will then appear immediately after the primary
service as you rotate the tuning control clockwise.
2. Press and release the Tuning control to select the station.
3. When the secondary service shuts down, your radio will automatically
switch back to the main radio station (or primary service) if it is
available.
1,2

9
Manual Tuning - DAB
Manual tuning allows you to tune directly to the various DAB Band III
channels. UK DAB stations located in the range 11B to 12D.
1. Press and hold in the Info button until the display shows "Manual
tune". Press and release the Tuning control to select this function.
2. Rotate the Tuning control to select the required DAB channel.
3. Press and release the Tuning control to select the desired channel.
The graph will indicate the signal strength, and the lower line will show
the name of the DAB Multiplex (group of radio stations). Any stations
found will be added to the stored list in the radio.
4. Press and release the Tuning control to return to the normal tuning
mode.
Signal strength display - DAB
1. Repeatedly press and release the Info button until the lower line of
the display shows signal strength.
2. Position your radio and try moving the aerial so as to give maximum
number of black rectangles on signal strength display. Normally, the best
reception will be found with the aerial vertical and fully extended.
3. The clear unfilled rectangle indicates minimum signal level required
for satisfactory reception.
2-4
1
1

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri) 10
1
Dynamic Range Control settings - DAB
Dynamic Range Control (also known as DRC) can make quieter sounds
easier to hear when your radio is used in a noisy environment.
1. Press the On/Off button to switch on your radio.
2. Press and hold in the Info button. The display will show “Manual
tune.”
3. Rotate the Tuning control until the display shows "DRC value".
4. Press and release the Tuning control to enter the adjustment
mode.
5. Rotate the Tuning control to select the required DRC setting (the
default is 0).
DRC 0 - DRC is switched off, Broadcast DRC will be ignored.
DRC 1/2 - DRC level is set to 1/2 that sent by broadcaster.
DRC 1 - DRC level is used as sent by broadcaster.
6. Press and release the Tuning control to confirm the setting. The
display will return to normal tuning mode.
Note: Not all DAB broadcasts are able to use the DRC function. If the
broadcast does not support DRC, then the DRC setting in the radio will
have no effect.
2
3-6

11
2
3
4-7
9
Operating your radio - Search tuning - FM
1. Carefully extend the telescopic aerial fully.
2. Press the On/Off button to switch on your radio.
3. Press the Band button to select the FM band.
4. Press and immediately release the Auto tune button, your radio will
scan in an upwards direction (low frequency to high frequency) and
stop automatically when it finds a station of sufficient strength.
5. After a few seconds the display will update. The display will show the
frequency of the signal found. If the signal is strong enough and there
is RDS data present then the radio will display the station name.
6. To find other stations, press and release the Auto tune button as
before.
7. To scan the FM band in a downwards direction (high frequency to low
frequency) press and hold down the Auto tune button for 0.5 seconds
and then release.
8. When the waveband end is reached your radio will recommence tuning
from the opposite waveband end.
9. Adjust the Volume control to the required setting.
The use of radio station presets for selecting your preferred radio stations
is described on page 16.

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri) 12
Manual tuning - FM
1. Press the On/Off button to switch on your radio.
2. Press the Band button to select the FM band. Carefully extend the
telescopic aerial fully for FM reception.
3. Rotate the Tuning control to tune to a station. With each click of the
control the frequency will change up or down by 50 kHz.
4. When the waveband end is reached the radio will recommence tuning
from the opposite waveband end.
5. Set the Volume control to the desired settings.
6. To switch off your radio press the On/Off button.
2
5
6
3
1

13
Display modes - FM
In FM mode the bottom line of the display can be set to any of the following
display options:-
1. Press the Info button to cycle through each of the options.
a. Scrolling text Displays scrolling text messages such
as artist/track name, phone in number
etc.
b. Program type Displays type of station being listened to
e.g. Pop, Classic, News, etc.
c. Time and date Displays the current time and date.
d. Frequency Displays frequency of the station being
listened to.
e. Audio mode Display shows Auto (stereo) or Mono.
Note: Your radio will display "NO RT" on the lower line of the display if
there is no scrolling text available and "NO PTY" if there is no programme
type information.
a
b
c
d
e
1

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri) 14
Favourite button
Your radio is fitted with a button which when pressed will automatically
select the required waveband and tune to your Favourite radio station.
With this button you can store one favourite station from either the DAB
or FM wavebands.
To set up your favourite station, follow these steps:
1. Carefully extend the telescopic aerial and switch on your radio.
2. Select the desired waveband (DAB or FM) and tune into the required
radio station as described on the preceding pages.
3. Press and hold down the Favourite button (for 5 seconds) until the
display shows "My Fav. saved".
Recalling your favourite station
1. Carefully extend the telescopic aerial and switch on your radio.
If your radio is in Auxiliary Input mode, press and release the DAB/FM
button to select normal radio operation.
2. Momentarily press the Favourite button, your radio will automatically
select the DAB or FM waveband as needed and then tune to the radio
station stored in the favourite memory.
3
2

15
Preset stations - DAB and FM
To make it easier for you to tune your radio to the stations that you prefer,
you may store selected radio stations as presets. Your radio holds presets
separately for DAB and FM radio modes.
You may set as many or as few presets as you like in each mode.
You can easily switch between displaying all DAB stations (or all FM
frequencies) and displaying only those that you have set as presets.
Any station or frequency which has been marked as a preset can easily
have the mark cancelled should your preferences or needs change.
Presets are retained when your radio is switched off.
1. To setup your preset stations, tune into the required station.
2. Press and hold down the Preset button until the displays shows a
tick symbol next to the radio station name or frequency. This indicates
that the radio station is marked as a preset. To cancel the preset mark,
press and hold the Preset button again.
3. Repeat steps 1 and 2 as needed for any other stations that you want
as presets.
4. To view only the preset stations for the currently select waveband
when tuning, press and release the Preset button so that the heart
symbol shows in the display.
5. To listen to one of the preset radio stations, rotate the Tuning control
until the required radio station is displayed. Press and release the
Tuning control to select and tune to that station.
6. To cancel the preset stations view, press and release the Preset button
so that the heart symbol disappears from the display. Your radio will
then be able to access the full station list using the Tuning control.
2,4
5
6

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri) 16
FM Stereo/Mono
1. If a station being received is weak some hiss may be audible (especially
when listening using headphones). To reduce this, press and release
the Tuning control so that the display shows "Switching to Mono".
Your radio will switch to mono mode.
2. To return to stereo mode press and release the Tuning control so
that the display shows "Switching to Auto". Your radio will switch to
stereo mode.
Note: Stereo listening is only available when listening via headphones or
when using the Line Out socket connected to an external amplifier.
1

Scan sensitivity setting - FM
Your radio will normally scan for FM broadcasts which are strong enough
to give good reception. However, you may wish the Auto-scan function
to also be able to find weaker signals, possibly from more distant radio
transmitters. Your radio includes a local / distant option for the Auto-scan
function.
1. Press the On/Off button to switch on your radio.
2. If needed, press the Band button to select the FM band.
3. Press and hold the Info button until the display shows "FM Scan
Zone" then press the Tuning control to enter the scan zone selection
menu.
4. Rotate the Tuning control to switch between Local and Distant options
on the lower line of the display. The Distant option will allow the radio
to find weaker signals when scanning.
5. Press and release the Tuning control to confirm your selection. The
radio will then revert to the normal information display. The Local or
Distant setting is stored in the radio and remains in force until changed
or until a System Reset.
Note: The initial setting (out of the box, or after a System Reset) causes
the radio to ignore weaker (or more distant) signals.
1
2
3-5
3
17

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
Software version
The software display cannot be altered and is just for your reference.
1. To view the software version on the display, ensure your radio is in
DAB mode and press and hold the Info button for 2 seconds.
2. Rotate the Tuning control until “SW Version” together with the version
number appears on the display.
3. After a few seconds the display will revert to the normal display
mode.
1
2
18

2,3
System reset
If your radio fails to operate correctly, or some digits on the display are
missing or incomplete, it may be possible to restore normal operation by
carrying our a System Reset operation on your radio. This will restore the
radio's settings to their factory defaults. No presets will be stored, and the
list of DAB radio stations will be empty.
If you have moved to a different part of the country and you wish to erase
local DAB radio stations that are no longer available from the stored list,
then you may carry out this procedure. Your radio will automatically re-scan
for the DAB stations available at your current location when it restarts.
1. Press and hold down the Info button for 2 seconds
2. Rotate the Tuning control until the display shows "Factory reset",
then press and release the Tuning control.
3. If you wish to perform the reset operation, press and release the Tuning
control one more time. A full reset of your radio will be performed.
All presets and station lists will be erased.
4. After a system reset a scan of the DAB band will be performed.
In case of malfunction due to electrostatic discharge, reset the product
(temporary disconnection of the power adaptor or removal or batteries
may be required) to resume normal operation.
If a problem persists our technical staff would be pleased to offer
any assistance on operating the radio. Our technical helpline number
is 020 8758 0338.
1
19