Robinson Willey RIVIERA User manual

•.4 ]\) t 'lOOn
THE GAS CONSUMERS'COUNCIL
(GCC) IS AN INDEPENDENT
ORGANISATION WHICH PROTECTS
THE INTEREST OF GAS USERS.
IF YOU NEED ADVICE,YOU WILL
FIND THE TELEPHONE NUMBER IN
YOUR LOCAL TELEPHONE
DIRECTORY UNDER GAS.
ROBINSO NILLEY
RIVI ERA GC No. 32-170-23 A
AND
BE LVE 0ERE GC No. 32-170-24 A
Cat II2H3PG20 at 20mbar convertible to G31 at 37mbar.
For use in GB andlE.
Users Instructions
THIS LEAFLET IS INTENDED TO HELP YOU UNDERSTAND ANDUSE YOUR NEWFIRE EFFICIENTLY.
PLEASE READ THESE INSTRUCTIONS BEFORE USING THE FIREANDKEEPFORFUTURE REFERENCE.
57568

TRIMS AND FENDERSi ~.
.•. ~ - . . ,. , -
Available in Black with
Brass or Chrome effect insert
~ig.4X
Available in
Brass or Chrome effect Both the above are available in
black/brass or black/chrome effect
57568

1. The appliance name and serial number are on the data badge which islocated on the lefthand side of the fire base panel.Remove
the fender and ash-pan cover for access to read the data badge.(See Figs 1and2).
3.This fire must be installed and serviced regularly in accordance with theGas Safety (Installation and Use) Regulations and the rules
in force by a competent person e.g.British Gas or CORGI member. Where solid fuel has been used the chimney must be swept
before installation.This fire must be installed in accordance with theinstallationinstructions.
4.It is recommended that at least once a year the appliance should be removed to check the catchment space and the chimney for
debris.The fire should be checked annually to ensure continuedclearance of combustionproducts and that there is no excessive
build up of soot.
5. WARNING:This fire has a naked flame.Also certain parts,especially the canopy,will be hot when in use.A fireguard conforming to
B.S.6539 (Fireguards for use with solid fuel appliances) should be usedfor the protectionof children,the elderly or the infirm.Such
a guard is also recommended for pet animals.
6. After the fire is installed you may wish to fix a shelf above.This is quite acceptableprovided that the underside of the shelf is at least
237mm above the fire and does not project more than 150mm forward.For a deeper shelf allow13mm increase in shelf height for
every 25mm increase in shelf depth.
8.When the fire is first used it may give off some slight smoke and smell but these will soon clear after a few hours of use at the HIGH
setting.
10.IMPORTANT: When considering fitting any heating
appliance or wallpapering a room in which one isfitted, if
blown vinyl or other heat sensitive wallpapers are used in
the vicinity of the heat source, then they may become heat
damaged or discoloured especially just above the fire.
11.It is important for safe operation and to maintain efficiency
that the fire is not operated with damaged or broken coals.
IMPORTANT NOTE: Under no circumstances should extra
coals be used together with the existing coals.
ONLY THE CORRECT CO LS SHOULD BE USED.
12.If purpose built ventilation is provided for the fire, it should
be checked periodically to ensure that it is free from
obstruction.
On pre-cast flue installations the walls must be dry lined
over the route of the flue. Dry lining is the use of
plasterboard with an air space between the wall and the
plaster board. Installation must not be made into pre-cast
flues that have plaster applied directly to the surface of the
wall i.e.wet lined,because experience has shown that in
some wet lined installations the lack of heat insulation
provided by plaster can cause the plaster to shrink or crack
and other decoration such as wallpaper to discolour or
detatch from the wall.
This product uses fuel effect pieces containingRefractory
Ceramic Fibre (RC F),which are man-made vitreous silicate
fibres. Excessive exposure to these materials may cause
temporary irritation to eyes skin and respiratory tract,
consequently, it makes sense to take care when handling
these articles to ensure that the release of dust is kept to a
minimum.
57568

• F ~- ~-
TO LIGHTAND OPERATE:- .
WARNING: If the flames are found to be extinguished and the control is not in the OFF position,the control knob should be returned to
the OFF position and no attempt should be made to light the gas until at least 3 minutes have elapsed.
SAFETY
The fire is fitted with a flame supervision device and anatmosphere sensing device which will shut off the gas supply iffor any reason the
pilot goes out.The device will also extinguish the pilotif the oxygen content in the room falls belowa prescribed level.If the fire keeps
going out, the fault must be rectified immediately by a competent person.
The control knob is located behind the fender ash-pan door.Depress the controlknob and rotate to the PILOT IIGN position until the
ignition sparks.Ifthe pilot did not light return thecontrolknob to the OFF position andtry again. Once the pilot is lit keep the control knob
pushed in for a further 10 seconds before releasing. Thepilot should remain lit.Referto Fig. 4 for viewing of the pilot when lit.
When the pilot is established,Turn the control knob totheHIGH position.Your fire is nowoperating on full heat input.You may now turn
the control knobto any of the positions,HIGH, MED,LOWor ECON.
57568

LIGHTING wITIif~ :",,~'
In the unlikely event of failure of the ignition spark the fire can be lit with ataper oralong spill.Remove the ash-pan and fender.You
should be able to see the pilot burner just below the coal bed to theleft ofcentre (see Fig 4.).Light your taper and apply itto the pilot
burner (Fig.4).Depress the control knob and rotate to thePILOT/IGN position.The pilot lightsandyou should keep the knob depressed
for 10 seconds before releasing.The pilot should remain alight.
57568

....•. ..•. ~
CLEANING AND SIMPLE MAIN l-ENANCE
Fig6.
1.The underside of the coal bed has grooves matching
the raised ports of the burner top. Fit thecoal bed by
placing it onto the burner.Take care to avoidda mag e as
you insert it pastthe pilot burner (Refer to Fig5.).Ensure
thatit iscorrectly located in the burner tray by sliding it
sideways and frontto back.
2. Insert the side cheeks by sliding them down the sideof the
matrix until they touch the rear brick effect panel.(Refer to
Fig6.)
3.Lower therearcoal into position at an angle as shown in
Fig?
4.Ensurethattherearcoaldrops backtowards the rearbrick
effectpanel and seats correctly into the base coal.(Refer
toFig 8.)
57568
Generally the firewill only need dusting.Any painted surface or
metal part should be cleanedwitha damp cloth only.Never use
any abrasive materials or metal polish on painted surfaces or
metalparts.
Should any soot accumulation become excessive,the fuel
effect pieces should be removed from the fire for cleaning.
Cleaning shouldbe carried out in a well-ventilated area or in the
open air,by gently brushing with the pieces held away from your
face so thatyouavoid inhaling the dust.We do not recommend
theuse of a normal domestic vacuum cleaner which may blow
dust back into the air.The appearance of the fire after you have
removed the loose coals is shown in Fig.8.If you need to
remove the coal bed to dust away larger particles then it is
necessarythat you first remove the rear coal (Fig ?)and the
side cheeks(Fig6.). As you lift out the coal base take care that
you do notdamage itagainst the pilot burner (Fig 5.) and also
take precautions thatparticles do not fall on your carpet etc.
Remove any deposits on the burner with a soft brush.
Periodically vacuum away any loose particles that have fallen
on the hearth orinto the base of the fire.
DO NOTINSTALL THE FIRE WITH BROKEN OR MISSING
COALS.USEONLYTHE COALS SUPPLIED WITH THE FIRE.

5.Fit the trim to the fire by hooking it overthe top of the firebox
top. Refer to Fig 9.
6.The bottom of the trim is held in place with magnets. Push
the bottom of the trim at each side onto the magnets.
NOTE:If the magnet on either side came away with the
trim on removal,transfer it back to the bump on the fire
before re-fitting the trim.Refer to Fig 10.
7.Position the fender centrally and slide towardsthe fire until
it touches the base coal.Refer to Fig 11.
57568

8.Place 4 rectangular coals onto the base coal with their
decorative faces visible.They should have the front end
touching the back of the fender or inline with it.Refer to Fig
12.
Place the 3 remaining rectangular coals resting in the 'V's
just created and leaning back to rest on the rear coal. Refer
to Fig 13.
57568

•• ><.~ : NOTEPAD ~ ;~
-- '
57568

SPARES AND SERVICE .1l<
For spares and service apply to your local supplier or installer stating that the appliance is a RIVIERA or BELVEDERE. The appliance
Product code and Serial number are marked on the data badge on the left hand side of the base panel (remove the fender and ash-pan
cover).
If any 'home improvements' are made to the dwelling in which a gas appliance is fitted, i.e. The fitting of an extractor fan, draught
proofing or double glazing,then the air supply to the appliance and the fluing of the appliance must be rechecked by a competent person
(e.g. A CORGI registered engineer).
WE RECOMMEND ANNUAL SERVICEIINSPECTION BY A COMPETENT PERSON (e.g.A CORGI REGISTERED SERVICE
ENGINEER) TO ENSURE CONTINUED SAFE OPERATION.
PARTS REPLACEABLE BY USER~
PART NUMBER DESCRIPTION
989583
Coal Pack
992220
Control Knob
822328
Trim Magnet
ROBINSON WILLEY LIMITED
Mill Lane,Old Swan,Liverpool.L13 4AJ.England.
Telephone:[phone] Fax:[phone]
www.robinson-willey.co.uk
57568