Rockler BLUMotion Blum 110 User manual

1
Blum 110° BLUMotion Inset
Face Frame Hinge Instructions
Vertical Positioning of Hinges
Although Euro-style concealed hinges allow for vertical
adjustment, the mounting plate must line up with the hinge arm if
the two are to snap together and provide the maximum possible
adjustment range. The easiest way to accomplish this is to mark
aligning horizontal centerlines on both the door and the cabinet
face frame. You need to consider the amount of the door’s overlay
or inset when calculating the centerline positions for the door.
1. For the top hinge, measure down from the top of the cabinet
opening to the desired mounting location (typically 2"-3") and
use a combination square to mark the horizontal centerline
on the back of the face frame. (For the bottom hinge,
measure up from the bottom of the cabinet opening.)
Note: Be sure your hinge positions will provide adequate
clearance for any pullouts.
2. To determine the centerline location on the door, start
with the distance you measured in Step 1.
• For overlay doors, add the amount the door will overlap
at that edge.
• For inset doors, subtract the amount of the reveal at
that edge.
3. Use the values calculated for the top and bottom hinge
locations in Step 2 and mark the horizontal centerlines on
the back of the door. Compare the distance between the lines
on the face frame with the distance between the lines on the
door to verify.
Installing Hinges
1. Refer to the Door Diagram to mark drilling locations for
the hinge cup holes and mounting screw holes on the door.
2. Using a 35mm Forstner bit, drill a hole 13mm deep for the
hinge cup, taking care to keep the bit as square as possible to
the door.
Note: For fast, easy and accurate location and drilling of hinge
cup holes, we recommend using the JIG IT Deluxe Concealed
Hinge Drilling System (53420, sold separately) along with a
Rockler 35mm Long-Shank Forstner Bit (10104, sold
separately). For those using a drill press, a dedicated
JIG IT setup block is available (58488, sold separately).
3. Drill pilot holes for the screws, taking care not to drill all
the way through the door
4. Position the hinge cup in the hole and use the included
screws to secure in place
5. Repeat Steps 2-4 at other hinge location(s).
Installing Mounting Plates
1. Refer to the Face Frame Diagram to mark drilling locations
for the hinge plates on the back of the face frame.
2. Drill pilot holes for the mounting screws, taking care not to
drill all the way through.
Note: For fast, easy and accurate location and drilling of
mounting plate pilot holes, we recommend using the JIG IT
Hinge Plate Template B (57706, sold separately) along
with a Rockler/Insty-Drive #6 Self-Centering Bit (68991,
sold separately).
3. Use the included screws to secure the mounting plates
onto the face frame
4. Mount the doors by clipping the hinge arms onto the
mounting plates.
Hinge Finish Tab Cup
Diameter
Cup
Depth
Minimum Door
Thickness
Maximum Door
Thickness Adjustments Gap Clip-on
Mounting
Minimum
Reveal
Blum 110°
Long Arm Nickel 5mm 35mm 13mm 16mm (.63") 26mm (1") 3-way cam 1mm Yes .5mm
Check Rockler.com for updates. If you have further questions, please
contact our Technical Support Department at 1-800-260-9663
or [e-mail]
BLUMotion
Soft Close
On/Off
Switch
35676

2Distributed by Rockler Companies, Inc.
©2015 Rockler Woodworking and Hardware
35676
Rev 06/15
32
9.5
5
22.5
Back of
Face Frame
All measurements are in millimeters.
Door Diagram Face Frame
Diagram
Turning this screw clockwise adjusts the
door down; counterclockwise, up.
Turning this screw clockwise adjusts the
door inward; counterclockwise, outward.
Height Adjustment Depth Adjustment Lateral Adjustment
Turning this screw clockwise adjusts
the door to the right; counterclockwise,
to the left.
OPTIONAL ACCESSORIES
9.5
45
JIG IT®Deluxe Concealed
Hinge Drilling Jig
53420
JIG IT®Template B
Hinge Drilling Jig
57706
JIG IT®5mm Hinge Cup
Drill Press Drilling Jig
58488
Cup Spacers and Angle
Restriction Clips
35245 and 31075
Inside Edge
of Door
Tab
Center
Mark
Centerline
Cup Depth Diagram
13
35
Door
Cabinet
Face Frame
Reveal
Reveal Diagram