Rockler Salice GRP40209 User manual

1
Salice 165° 1/2" Overlay
Face Frame Pie Corner
Hinge Kit Instructions
Vertical Positioning of Hinges
Although Euro-style concealed hinges allow for vertical
adjustment, the mounting plate must line up with the hinge arm if
the two are to snap together and provide the maximum possible
adjustment range. The easiest way to accomplish this is to mark
aligning horizontal centerlines on both the doors and the cabinet
face frame. You need to consider the amount of the doors’ overlay
or inset when calculating the centerline positions for the doors.
1. For the top hinge, measure down from the top of the cabinet
opening to the desired mounting location (typically 2"-3") and
use a combination square to mark the horizontal centerline on
the inside edge of the face frame. (For the bottom hinge,
measure up from the bottom of the cabinet opening.)
Note: Be sure your hinge positions will provide adequate
clearance for any pullouts.
2. To determine the centerline location on the door, start with
the distance you measured in Step 1 and add the amount
the door will overlap at that edge.
3. Use the values calculated for the top and bottom hinge
locations in Step 2 and mark the horizontal centerlines on
the back of the door. Compare the distance between the lines
on the cabinet with the distance between the lines on the
door to verify.
Note: Building a bi-fold door system requires installing two pairs
of hinges — 165˚ face-frame cabinet hinges (the larger pair) and
bi-fold door hinges. The 165˚ hinges attach to the side of the
cabinet and to Door 1. The bi-fold hinges connect to Door 1
and Door 2.
56511
Hinge Finish Tab Cup
Diameter
Cup
Depth
Minimum Door
Thickness
Maximum Door
Thickness Adjustments Gap Clip-on
Mounting
Minimum
Reveal
Salice Pie
Corner Kit Titanium 4mm 35mm 11mm 15mm (.59") 19mm (.75") 3-way cam .7mm Yes 1.5mm

2
Installing Hinges on Door 1
1. Refer to the Door 1 Diagram to mark drilling locations for
the hinge cup holes and mounting screw holes on the door.
2. Using a 35mm Forstner bit, drill a hole 11mm deep for the
hinge cup, taking care to keep the bit as square as possible
to the door.
Note: For fast, easy and accurate location and drilling of
hinge cup holes, we recommend using the JIG IT Deluxe
Concealed Hinge Drilling System (53420, sold separately)
along with a Rockler 35mm Long-Shank Forstner Bit (10117,
sold separately). For those using a drill press, a dedicated
JIG IT setup block is available (58223, sold separately).
3. Drill pilot holes for the screws, taking care not to drill all
the way through the door.
4. Position the hinge cup in the hole and use the included
screws to secure in place.
5. Repeat Steps 2-4 at other hinge location(s).
Installing Mounting Plates in Cabinet
1. Refer to the Face Frame Diagram to mark drilling locations
for the hinge plates.
2. Drill pilot holes for the mounting screws.
Note: For fast, easy and accurate location and drilling of
mounting plate pilot holes, we recommend using the “Cabinet”
Check Rockler.com for updates. If you have further questions, please
contact our Technical Support Department at 1-800-260-9663
or [e-mail]
side of JIG IT Hinge Plate Template E (55909, sold separately)
along with a Rockler/Insty-Drive #6 Self-Centering
Bit (68991, sold separately).
3. Use the included screws to secure the mounting plates
onto the face frame.
Installing Mounting Plates on Door 2
1. Refer to the Door 2 Diagram to mark drilling locations for
the hinge plates.
2. Drill pilot holes for the mounting screws, taking care not
to drill all the way through.
Note: For fast, easy and accurate location and drilling of
mounting plate pilot holes, we recommend using the “Door”
side of JIG IT Hinge Plate Template E (55909, sold separately)
along with a Rockler/Insty-Drive #6 Self-Centering Bit (68991,
sold separately).
3. Use the included screws to secure the mounting plates
onto Door 2.
4. Mount the doors by clipping the hinge arms onto the
mounting plates.
Turning this screw clockwise adjusts the
door down; counterclockwise, up.
Turning this screw clockwise adjusts the
door inward; counterclockwise, outward.
Height Adjustment Depth Adjustment Lateral Adjustment
Turning this screw clockwise adjusts
the door to the right; counterclockwise,
to the left.
Door 1
Door 2
Door 1
Door 2
Door 1
Door 2

3
Distributed by Rockler Companies, Inc.
©2015 Rockler Woodworking and Hardware
56511
Rev 09/15
45
4
21.5
Face
Frame
Edge
All measurements are in millimeters.
Door 1 Diagram
9.5
9.5
OPTIONAL ACCESSORIES
JIG IT®Deluxe Concealed
Hinge Drilling Jig
53420
JIG IT®Template E
Door Hinge Jig
55909
JIG IT®4mm Hinge Cup
Drill Press Drilling Jig
58233
Inside Edge
of Door
Tab Center
Mark
Centerline
Cabinet
Diagram
Door 1 Door 2
Inside Edge
of Door
Inside Edge
of Door
21.59.5
4
48
28
32
Tab
Center
Mark Centerline
Door 2 Diagram
Cup Depth Diagram
11
35
Door
Cabinet
Face Frame
Gap
Gap and Reveal
Reveal