Rockwell Automation 2711P-RPA User manual

Installation Instructions
Logic Module, Internal CompactFlash, and RAM
Catalog Numbers 2711P-Rxxxx
About the Components
This document provides information on how to install these components:
•Logic module on a PanelView Plus or PanelView Plus CE device
•Memory (RAM and internal CompactFlash) in the logic module
For complete information on installing, wiring, and troubleshooting the terminals, refer to the
publications listed under Additional Resources.
This document refers to FactoryTalk View ME software that was previously named RSView
ME software.
Topic Page
About the Components 1
Important User Information 2
Safety Precautions 3
About the Logic Module 3
Electrostatic discharge (ESD) wristband 5
Install or Replace RAM 7
Install or Replace the Internal CompactFlash 8
Marine Applications 11
Install a Logic Module 12
Replace a Logic Module 13
Additional Resources 14
www.aotewell.com [email protected]
www.aotewell.com [email protected]

2Logic Module, Internal CompactFlash, and RAM
Publication 2711P-IN004J-EN-P - September 2009
Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical equipment.
Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication
SGI-1.1 available from your local Rockwell Automation sales office or online at
http://literature.rockwellautomation.com) describes some important differences between solid state
equipment and hard-wired electromechanical devices. Because of this difference, and also because of the
wide variety of uses for solid state equipment, all persons responsible for applying this equipment must
satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many
variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot
assume responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING Identifies information about practices or circumstances that can cause an explosion in
a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.
IMPORTANT Identifies information that is critical for successful application and understanding of
the product.
ATTENTION Identifies information about practices or circumstances that can lead to personal injury
or death, property damage, or economic loss. Attentions help you identify a hazard,
avoid a hazard and recognize the consequences.
SHOCK HAZARD
Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that dangerous voltage may be present.
BURN HAZARD
Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that surfaces may reach dangerous temperatures.

Logic Module, Internal CompactFlash, and RAM 3
Publication 2711P-IN004J-EN-P - September 2009
Safety Precautions
Before installing or replacing components and modules, disconnect power from the terminal.
During the installation, be careful not to touch any of the exposed electronic components.
About the Logic Module
The logic module has these features:
•Status indicators
•Input power, DC or AC
•Ethernet port, serial port, two USB ports, CompactFlash card slot
•RAM and internal CompactFlash with firmware or operating system
Logic modules are available as separate catalog numbers for field installation and are shipped
with or without memory installed. If RAM and internal CompactFlash are ordered separately,
you must install these components before attaching the logic module to the display module.
SHOCK HAZARD Disconnect all power from the terminal before installing or replacing any components.
Failure to disconnect power may result in electrical shock or damage to the terminal.
ATTENTION Be careful when touching any of the exposed electronic components to prevent damage
from electrostatic discharge (ESD). Work in a static free environment and wear a properly
grounded ESD wristband.
Logic Module
Display Module
www.aotewell.com [email protected]

4Logic Module, Internal CompactFlash, and RAM
Publication 2711P-IN004J-EN-P - September 2009
PanelView Plus and PanelView Plus CE Logic Modules
Cat. No. Description
PanelView Plus or PanelView Plus CE 700 to 1500 Logic Modules (1)
(1) These logic modules are compatible with any of the 2711P-RWxinternal CompactFlash cards.
2711P-RP Logic module without flash/RAM memory, DC input
2711P-RPA Logic module without flash/RAM memory, AC input(2)
(2) These logic modules are approved for marine applications.
2711P-RPD Logic module without flash/RAM memory, isolated DC input(2)
PanelView Plus 700 to 1500 Logic Modules
2711P-RP1 Logic module with 64 MB flash/64 MB RAM, DC input
2711P-RP1A Logic module with 64 MB flash/64 MB RAM, AC input(2)
2711P-RP1D Logic module with 64 MB flash/64 MB RAM, isolated DC input(2)
2711P-RP2 Logic module with 128 MB flash/128 MB RAM, DC input
2711P-RP2A Logic module with 128 MB flash/128 MB RAM, AC input(2)
2711P-RP2D Logic module with 128 MB flash/ 128 MB RAM, isolated DC input(2)
2711P-RP2DK Conformal-coated logic module with 128 MB flash/128 MB RAM, isolated DC input
2711P-RP2K Conformal-coated logic module with 128 MB flash/128 MB RAM, DC input
2711P-RP3 Logic module with 256 MB flash/256 MB RAM, DC input
2711P-RP3A Logic module with 256 MB flash/256 MB RAM, AC input(2)
2711P-RP3D Logic module, 256 MB flash/256 RAM, isolated DC input(2)
PanelView Plus CE 700 to 1500 Logic Modules
2711P-RP6 PanelView Plus CE logic module with 128 MB flash/128 MB RAM, DC input
2711P-RP6A PanelView Plus CE logic module with 128 MB flash/128 MB RAM, AC input(2)
2711P-RP6D PanelView Plus CE logic module with 128 MB flash/128 MB RAM, isolated DC input(2)
2711P-RP6K PanelView Plus CE conformal-coated logic module with 128 MB Flash/128 MB RAM, DC input
2711P-RP6DK PanelView Plus CE conformal-coated logic module with 128 MB flash/128 MB RAM, isolated
DC input
2711P-RP7 PanelView Plus CE logic module with 256 MB flash/256 MB RAM, DC input
2711P-RP7A PanelView Plus CE logic module with 256 MB flash/256 MB RAM, AC input(2)
2711P-RP7D PanelView Plus CE logic module with 256 MB flash/256 MB RAM, isolated DC input(2)
www.aotewell.com [email protected]

Logic Module, Internal CompactFlash, and RAM 5
Publication 2711P-IN004J-EN-P - September 2009
Required Tools
The following tools are required for installation:
•#1 and #2 Phillips screwdriver
•Electrostatic discharge (ESD) wristband
Component Compatibility for PanelView Plus CE Terminals
It is important to match the series of the internal CompactFlash card with the correct series
of the logic module and software version. The series of the CompactFlash determines the
version of FactoryTalk View ME software and version of the operating system. The logic
module is available with or without memory installed.
Logic Module Compatibility
6189-RPx, 6189-RPRHx, 6189-RPEHx,
2711P-RPx, 2711P-RPx, 2711P-RP6x,
2711P-RP7x
Internal CompactFlash
6189-RW2, 6189-RW3,
6189-RW4, 2711P-RW6,
2711P-RW7, 2711P-RW8
FactoryTalk View ME and
OS Software Version
Series A: 6189-RPxH/A(1)
(1) When upgrading from FactoryTalk View ME software, version 3.0 to 3.10 or later, the Firmware Upgrade Kit is
recommended.
Series B: 6189-RWx/B FactoryTalk View ME 3.0
Windows CE 3.0
Series B: 6189-RPxH/B Series C: 6189-RWx/C FactoryTalk View ME 3.10
Windows CE 4.1
Series B: 6189-RPxH/B
Series C: 6189-RPxH/C
Series D: 6189-RPxH/D
Series E: 6189-RPxHx/E
Series F: 2711P-RPxx/F(2)
Series G: 2711P-RPxxx/G(2)
(2) Series F and later logic modules work with PanelView Plus and PanelView Plus CE CompactFlash cards.
Series D: 6189-RWx/D
Series E: 6189-RWx/E
FactoryTalk View ME 3.20
Windows CE 4.1
Series F: 6189-RWx/F
Series G: 6189-RWx/G
Series H: 2711P-RWx/H
FactoryTalk View ME 4.0
Windows CE 4.1
Series J: 2711P-RWx/J FactoryTalk View ME 5.0 or 5.1
Windows CE 4.1
www.aotewell.com [email protected]

6Logic Module, Internal CompactFlash, and RAM
Publication 2711P-IN004J-EN-P - September 2009
Component Compatibility for PanelView Plus Terminals
It is important that you match the series of the internal CompactFlash card with the correct
series of the logic module and software version. The series of the CompactFlash determines
the version of FactoryTalk View ME software. The logic module is available with or without
memory installed.
Compatibility After Upgrade
FactoryTalk View ME terminals are compatible with .MER applications that are the same or a
previous revision. For example, FactoryTalk View ME 3.20 terminals can run .MER
applications for FactoryTalk View ME software, versions 3.0, 3.10, and 3.20.
For PanelView Plus CE devices, the appropriate changes are made to the OS, from Windows
CE software, version 3.0 to 4.1, when upgrading from FactoryTalk View ME software,
version 3.0 to 3.10 or later.
Logic Module Compatibility
2711P-RPx, 2711P-RP1x,
2711P-RP2x, 2711P-RP3x
Internal CompactFlash
2711P-RW1, 2711P-RW2,
2711P-RW3
FactoryTalk View ME
Software Version
Series A: 2711P-RPx/A(1)
(1) Series A logic modules are compatible with series B CompactFlash cards. When upgrading from FactoryTalk View ME
software, version 3.0 to 3.10 or later, the Firmware Upgrade Kit is required.
Series B: 2711P-RWx/B FactoryTalk View ME 3.0
Series B: 2711P-RPx/B Series C: 2711P-RWx/C FactoryTalk View ME 3.10
Series B: 2711P-RPx/B
Series C: 2711P-RPx/C
Series D: 2711P-RPx/D
Series E: 2711P-RPxx/E
Series F: 2711P-RPxx/F(2)
Series G: 2711P-RPxxx/G(2)
(2) Series F and later logic modules work with PanelView Plus and PanelView Plus CE CompactFlash cards.
Series D: 2711P-RWx/D
Series E: 2711P-RWx/E
FactoryTalk View ME 3.20
Series F: 2711P-RWx/F
Series G: 2711P-RWx/G
Series H: 2711P-RWx/H
FactoryTalk View ME 4.0
Series J: 2711P-RWx/J FactoryTalk View ME 5.0 or 5.1

Logic Module, Internal CompactFlash, and RAM 7
Publication 2711P-IN004J-EN-P - September 2009
Install or Replace RAM
The logic module is available with or without RAM installed. If ordered separately, you must
install the RAM before attaching the logic module to the display module.
RAM Memory Modules
Follow these steps to install or replace RAM.
1. Turn the logic module over to expose the circuit board.
2. Locate the RAM module on the circuit board.
3. Pull the metal retaining clips away from the module and slide out the RAM module.
4. Insert the new RAM module at a 45° angle and snap down.
Cat. No. Description
2711P-RR64 64 MB SODIMM RAM for PanelView Plus and PanelView Plus CE terminals
2711P-RR128 128 MB SODIMM RAM for PanelView Plus and PanelView Plus CE terminals
2711P-RR128K Conformal-coated 128 MB SODIMM RAM for PanelView Plus and PanelView
Plus CE terminals
2711P-RR256 256 MB SODIMM RAM for PanelView Plus and PanelView Plus CE terminals
RAM
Module
CompactFlash Card
Retaining Clip
Screw
Retaining Clips

8Logic Module, Internal CompactFlash, and RAM
Publication 2711P-IN004J-EN-P - September 2009
Install or Replace the Internal CompactFlash
The logic module is available with or without CompactFlash installed. If ordered separately,
you must install the CompactFlash before attaching the logic module to the display module.
Internal CompactFlash
Follow these steps to replace the internal CompactFlash.
1. Turn the logic module over to expose the circuit board.
2. Unscrew and remove the retaining clip that secures the internal CompactFlash card.
3. Pull out the internal CompactFlash card.
4. Insert the new internal CompactFlash card.
5. Reattach the retaining clip.
Cat. No.(1)
(1) The 2711P-RP, 2711P-RPD, and 2711P-RPA logic modules are compatible with any of the internal CompactFlash options.
Description
2711P-RW1 64 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus
logic modules
2711P-RW2 128 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus
logic modules
2711P-RW3 256 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus
logic modules
2711P-RW6 128 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus CE
logic modules
2711P-RW7 256 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus CE logic
modules
2711P-RW8 512 MB internal CompactFlash with FactoryTalk View ME software for PanelView Plus CE logic
modules
www.aotewell.com [email protected]

Logic Module, Internal CompactFlash, and RAM 9
Publication 2711P-IN004J-EN-P - September 2009
Battery Precautions
Replace the Battery in PanelView Plus Terminals
Follow these steps to replace the battery in the logic module of PanelView Plus or PanelView
Plus CE terminals.
1. Disconnect power from the terminal.
2. Place the terminal, display side down, on a flat stable surface.
3. Detach the communication module, if attached, from the logic module by removing
the four screws.
4. Loosen the six captive screws that attach the logic module to the display module.
5. Carefully lift the logic module away from the terminal and turn over to expose the
circuit board.
WARNING When you connect or disconnect the battery, an electrical arc can occur. This could cause
an explosion in hazardous location installations. Be sure that power is removed or the
area is nonhazardous before proceeding.
For safety information on the handling of lithium batteries, including handling and
disposal of leaking batteries, see Guidelines for Handling Lithium Batteries, publication
AG 5-4. Replace the battery only with the indicated catalog number.
Do not dispose of battery in a fire or incinerator. Dispose of used batteries in accordance
with local regulations.
Store batteries in a cool, dry environment. We recommend 25 °C (77 °F) with 40…60%
relative humidity. You may store batteries for up to 30 days between -45…85 °C
(-49…185 °F), such as during transportation. To avoid possible leakage, do not store
batteries above 60 °C (140 °F) for more than 30 days.
Logic Module
Communication Module
Screw
Captive
Screw
Display Module

10 Logic Module, Internal CompactFlash, and RAM
Publication 2711P-IN004J-EN-P - September 2009
6. Locate the battery on the circuit board.
7. Remove the battery by lifting up the side of the battery.
8. Insert the new battery.
9. Reattach the logic module by aligning the two connectors on the bottom of the
module with the connectors on the terminal.
10. Push down on the logic module until it is firmly seated.
11. Tighten the six captive screws that secure the logic module to a torque of 0.58 N•m
(5…7 lb•in).
12. Reattach the communication module, if necessary, and tighten the four screws to a
torque of 0.58 N•m (5…7 lb•in).
Lift up the edge of the
battery indicated by
the arrow.
www.aotewell.com [email protected]