Rockwell Savoy User manual

Rockwell TM

1. Key

2. Cylinder or Cyl. housing and cylinder

3. Cylinder Backplate

4. External Pull Assembly

5. Deadbolt Mounting Plate

6. Deadbolt Mounting Screws

7. Spindle

8. Spindle Collar

9. Latch Mounting Plate

10. Internal Deadbolt Plate Assembly

11. Oval Head Machine Screws

12. Latch Mounting Plate Screws

13. Screw Washer

14. Flat Head Machine Screw

15. Screw Cover

16. Latch Rosette

17. Plastic Washer

18. Lever

19. Set Screw

20. Rosette Pick

21. Allen Wrench

22. Right Hand Spindle Cartridge (LEFT

hand spindle Cartridge Pre-installed)

23. Tapping Screw

EXPLODED VIEW

1. Door Preparation

A.Measure thickness of your door.

Ensure door is at

least 1-3/4" thick. If door thickness is less than

1-3/4" DO NOT PROCEED WITH

INSTALLATION.

B.Fold the marking template for the handle set

on the line and place on the door aligning A and

B of the template with the double bore of door.

Locate and mark hole E with a pencil. Carefully

drill hole E perpendicularly (at a 90°) to door

with a 3/8" drill bit.

IMPORTANT: Double check hole E location

before drilling .

2. Determine the handing of your door. Standing

on the outside of the door, if the hinges are to the

left of the door then the door is left handed

and if the hinges are to the right of the door then

the door is right handed. Handle sets are supplied

with left and right hand spindle cartridge to

work on both left and right hand doors

3. The handle sets are preset to work with a Left hand door,

should you have a right hand door, the left handed spindle

cartridge will need to be switched to a right hand spindle

cartridge. Right Hand Spindle Cartridge (included) has

instructions on changing from left to right hand . For Left hand

doors please proceed to step 4. For Right hand doors, please

replace the spindle cartridge to the correct hand prior to

proceeding to step 4. The handle set will not work if the

incorrect cartridge is installed .

Savoy Windsor

13 14 15

611

If door thickness is less

than 1- 3

4"do not install

the spindle collar

REQUIRED TOOLS

-Protective Eyewear

-#2 Phillips Screwdriver

-Pencil

-1

8" Drill Bit

MULTIPOINT HANDLE SET

INSTALLATION INSTRUCTIONS

OUTSIDE

HINGE

LEFT HANDED DOOR

RIGHT HANDED DOOR

LEFT

HAND DOOR

(PREINSTALLED)

RIGHT

HAND

DOOR

86-MPMHS-903 REV. B1 / 2

BEFORE YOU BEGIN

Check door thickness as handle will work with

a 1-3

4" thick door only. If door thickness is

greater than 1- 3

4" up to 2- 1

4" thick please

contact Rockwell Security Inc.

Remove and discard all packaging materials

and verify you have all the parts in the

exploded view section of instructions

Follow step by step installation instructions

to ensure proper operation of handle set.

Always wear protective eyewear.

(2) DEADBOLT MOUNTING SCREW

#10-32 x 2"

(2) 7/8 " OVAL HEAD MACHINE SCREWS

#8 x 7/8"

(2) MOUNTING PLATE SCREWS

#8-32 x 1-1/2"

(1) FLAT HEAD MACHINE SCREWS

#8-32 x 2-1/2"

(2) SET SCREWS

1/4"-20

(1) TAPPING SCREW

#8 x 1"

SPINDLE

COLLAR

SHORT

END

INSIDE

4. Slide the spindle collar onto the long end of the

spindle. If door thickness is less than 1- 34

" spindle

collar is not required.

From the inside of the door

insert the short end of the spindle into the latch hub

of the lock ensuring the groove side of the long end

of the spindle is facing down. If door thickness is 1- 3

4",

then also install the spindle collar onto the long side

of the spindle

SPINDLE

GROOVE SIDE

FACING DOWN

LONG

END

Spindle Collar

Short end

LONG END

7. Install the rosette and screw cover. Align the

notches on the latch mounting plate with the notches of the

rosette and snap the rosette onto the latch mounting

plate. Install bottom screw with screw washer.

Tighten the 2-1/2" flat head machine screw and attach

the screw on the screw cover washer.

DO NOT OVER TIGHTEN SCREWS.

12. Install the internal deadbolt plate assembly by positioning the

internal deadbolt plate assembly over the deadbolt mounting plate,

inserting the key cylinder tailpiece into the turnpiece. Secure in place

by fastening two 7/8" ( 1/2" for windsor) oval head machine screws

through the two countersunk holes on the turnpiece trim.

ROTATE THE THUMBTURN TO ENSURE DEADBOLT LOCKS. PLEASE

REFER TO TROUBLESHOOTING SECTION IF DEADBOLT DOES NOT LOCK.

5. After inserting the short end of the spindle

from inside the door, hold in place and install the

external handle assembly by inserting the posts

through the lock and the spindle through the

square hole in the spindle cartridge.

6. Insert the two 1-1/2" machine screws

through the latch mounting plate and into the

spindle cartridge and secure using a hand

screw driver.

DO NOT OVER TIGHTEN SCREWS.

8. Install the lever. Plastic washers are already preinstalled

on the levers. Place the plastic washer on the shank of the

knob or lever. Spare washer is also packed. Slip the lever

onto the spindle. While pressing the lever snuggly against the

rosette insert and tighten the set screw with the provided Allen

wrench. Install the tapping screw on the Rosette, best to

predrill a hole prior to installation.

CYLINDER

TAILPIECE INSTALLED

10. Install the Cylinder. Keeping the tailpiece

on the cylinder vertical, from the exterior of the

door insert the cylinder through the cylinder

backplate and into the "+" slot of the deadbolt.

TOP

11. Install the deadbolt mounting plate.

From the interior of the door orient the

deadbolt mounting plate and secure by

inserting the two 2" pan head machine

screws through the deadbolt mounting

plate, lock, and into the cylinder.

Ensure plastic Washer is

installed on lever

Ensure the spindle is

inserted through the lock

until it stops

This product comes packed

with both left and right hand

levers. Only one is used. To

determine which lever is

needed, make sure the

handle portion of the lever

extends to the hinge side of

the door and the set screw

faces down.

Snap on Rosette - Align

the notches on the

rosette with the notches

on the mounting plate.

Snap on by pushing down

on the top spring to

ensure proper contact of

bottom spring with the

bottom notch on the

rosette.

9. From the outside of the door, keeping the tailpiece of

the cylinder vertical, insert the tailpiece through the external

cylinder backplate and through the "+" hole on the lock.

DO NOT INSERT THE KEY INTO THE CYLINDER

DURING THIS STEP.

Note: IMPROPER ORIENTATION OF THE TAILPIECE

WILL CAUSE THE DEADBOLT NOT TO FUNCTION

PROPERLY .

CORRECT ORIENTATION

IN VERTICAL POSITION INSIDE

INSIDE

DEADBOLT IS

EXTENDED.

INSIDE

THUMBTURN

HORIZONTAL

PROBLEM

Can't extend (lock) deadbolt unless key is in cylinder. Can't remove key from

cylinder when the deadbolt is extended (locked).

When thumb grip is depressed or knob/lever is rotated the latch catches and

doesn't spring back.

Knob or lever keeps coming off the spindle

Deadbolt can easily be locked using the internal deadbolt plate assembly on the

inside but is difficult to lock when locked with the key from the outside.

The thumb grip cannot be depressed to retract the latch.

Cannot extend deadbolt with the internal deadbolt plate assembly or key when

door is closed.

SOLUTION

Cylinder tailpiece is not oriented properly. Remove the cylinder by first removing the internal deadbolt plate assembly and deadbolt mounting plate . Rotate the

cylinder tailpiece to the vertical position ensuring the deadbolt latch is extended and re-install the deadbolt assembly. Refer to steps 9 thru 12.

Ensure door is at least 1-3/4" thick. The latch mounting plate is installed too tight. Referring to step 6 , back the two 1-1/2" flathead machine screw out until the latch

operates freely

Ensure the spindle is oriented with the groove facing down and the set screw is securely tightened. Refer to steps 4 and 8.

The cylinder is not properly aligned with the internal deadbolt plate assembly or improper door thickness. Remove the internal deadbolt plate assembly and

loosen the two mounting plate screws. Align the cylinder and retighten the deadbolt mounting screws. Ensure your door thickness is at least 1-3/4" thick

Ensure door is at least 1-3/4" thick and the correct hand spindle cartridge is installed. Remove the handle and re-install refer to step 2 thru 6. Ensure the correct

hand (left or right hand) spindle cartidge is installed.

Open door and try to extend deadbolt. If deadbolt extends easily with the door open then the strike is not aligned with the deadbolt and/or locking points.

Adjust the strike to align with the deadbolt and/or locking points.

TROUBLE SHOOTING GUIDE

86-MPMHS-903 REV. B

2 / 2

ENSURE THE

DEADBOLT IS

EXTENDED.

INSIDE

Screw Cover washer and screw

Screw cover

Rosette

Adaptor