Rohde & Schwarz ETL 2112.0004.13 User manual

R&S®ETL
TV Analyzer
Getting Started
Getting Started
Version 04
2118413002
(EBYN2)

This document describes the following R&S®ETL model:
●2112.0004.13
U.S. Patent Nos. 4,631,603; 4,819,098; 4,907,093; 5,315,448; 6,381,747; and 6,516,132. Used for the
video and audio hardware decoder option (R&S ETL-B281).
The software contained in this product uses several valuable open source software packages. For information, see the "Open
Source Acknowledgment" document, which is available for download from the R&S ETL product page at www.rohde-schwarz.com/
product/etl.html > "Downloads" > "Firmware".
Rohde & Schwarz would like to thank the open source community for their valuable contribution to embedded computing.
© 2018 Rohde & Schwarz GmbH & Co. KG
Mühldorfstr. 15, 81671 München, Germany
Phone: [phone] - 0
Fax: [phone]
Email: [email protected]
Internet: www.rohde-schwarz.com
Subject to change – Data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
2118.4130.02 | Version 04 | R&S®ETL
Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol , e.g. R&S®ETL is indicated as
R&S ETL.

1171.1307.42 - 05
1
Safety Instructions
Instrucciones de seguridad
Sicherheitshinweise
Consignes de sécurité
Risk of injury and instrument damage
The instrument must be used in an appropriate manner to prevent
electric shock, fire,
personal injury or instrument damage.
●
Do not open the instrument casing.
●
Read and observe the "Basic Safety Instructions" delivered as
printed brochure with the instrument.
●
Read and observe the safety instructions in the following sections.
Note that the data sheet may specify additional operating conditions.
●
Keep the "Basic Safety Instructions" and the product documentation
in a safe place and pass them on to the subsequent users.
Riesgo de lesiones y daños en el instrumento
El instrumento se debe usar de manera adecuada para p
revenir
descargas eléctricas, incendios, lesiones o daños materiales.
●
No abrir la carcasa del instrumento.
●
Lea y cumpla las "Instrucciones de seguridad elementales"
suministradas con el instrumento como folleto impreso.
●
Lea y cumpla las instrucciones de seguridad incluidas en las
siguientes secciones. Se debe tener en cuenta que las
especificaciones técnicas pueden contener condiciones adicionales
para su uso.
●
Guarde bien las instrucciones de seguridad elementales, así como
la documentación del producto, y entréguelas a usuarios
posteriores.

1171.1307.42 - 05
2
Gefahr von Verletzungen und Schäden am Gerät
Betreiben Sie das Gerät immer ordnungsgemäß, um elektrischen
Schlag, Brand, Verletzungen von Personen oder Geräteschäden zu
verhindern.
●
Öffnen Sie das Gerätegehäuse nicht.
●
Lesen und beachten Sie die "Grundlegenden Sicherheitshinweise",
die als gedruckte Broschüre dem Gerät beiliegen.
●
Lesen und beachten Sie die Sicherheitshinweise in den folgenden
Abschnitten; möglicherweise enthält das Datenblatt weitere
Hinweise zu speziellen Betriebsbedingungen.
●
Bewahren Sie die "Grundlegenden Sicherheitshinweise" und die
Produktdokumentation gut auf und geben Sie diese an weitere
Benutzer des Produkts weiter.
Risque de blessures et d'endommagement de l'appareil
L'ap
pareil doit être utilisé conformément aux prescriptions afin d'éviter
les électrocutions, incendies, dommages corporels et matériels.
●
N'ouvrez pas le boîtier de l'appareil.
●
Lisez et respectez les "consignes de sécurité fondamentales"
fournies avec l’appareil sous forme de brochure imprimée.
●
Lisez et respectez les instructions de sécurité dans les sections
suivantes. Il ne faut pas oublier que la fiche technique peut indiquer
des conditions d’exploitation supplémentaires.
●
Gardez les consignes de sécurité fondamentales et la
documentation produit dans un lieu sûr et transmettez ces
documents aux autres utilisateurs.

Contents
R&S®ETL
3Getting Started 2118.4130.02 ─ 04
Contents
1 Preface.................................................................................................... 7
1.1 For Your Safety..............................................................................................................7
1.2 Information Provided on the Instrument.....................................................................7
1.3 Conventions Used in the Documentation...................................................................8
2 Documentation Overview....................................................................10
2.1 Getting Started Manual...............................................................................................10
2.2 User Manuals and Help...............................................................................................10
2.3 Tutorials....................................................................................................................... 10
2.4 Basic Safety Instructions........................................................................................... 10
2.5 Data Sheets and Brochures....................................................................................... 11
2.6 Release Notes and Open Source Acknowledgment (OSA)..................................... 11
2.7 Application Notes, Application Cards, White Papers, etc....................................... 11
3 System Overview................................................................................. 12
4 Setting Up the Instrument................................................................... 13
4.1 Unpacking the Instrument..........................................................................................13
4.1.1 Inspecting for Shipping Damage................................................................................... 13
4.1.2 Unpacking the Cardboard Box...................................................................................... 13
4.1.3 Checking the Accessories.............................................................................................14
4.1.4 Warranty Conditions......................................................................................................14
4.2 Putting Up the Instrument.......................................................................................... 14
4.2.1 Placing the Instrument on a Bench Top........................................................................ 14
4.2.2 Mounting the Instrument in a Rack............................................................................... 16
5 Interfaces and Connectors..................................................................17
5.1 Front Panel.................................................................................................................. 17
5.1.1 ON/STANDBY Key........................................................................................................18
5.1.2 Keys for Frequently-Used Functions.............................................................................18
5.1.3 Keys for Operating Softkeys......................................................................................... 19
5.1.4 Keys for Changing Softkey Menus................................................................................19
5.1.5 RUN Key....................................................................................................................... 21
5.1.6 Keypad.......................................................................................................................... 21

Contents
R&S®ETL
4Getting Started 2118.4130.02 ─ 04
5.1.7 Rotary Knob.................................................................................................................. 22
5.1.8 Cursor Keys.................................................................................................................. 23
5.1.9 GEN OUT 50 Ω Output................................................................................................. 24
5.1.10 USB Interfaces.............................................................................................................. 24
5.1.11 AF OUT Output............................................................................................................. 24
5.1.12 RF IN 75 Ω Input (B203 Option)....................................................................................25
5.1.13 RF IN 50 Ω Input........................................................................................................... 25
5.1.14 Display.......................................................................................................................... 25
5.2 Rear Panel....................................................................................................................26
5.2.1 Standard Rear Panel Connectors................................................................................. 26
5.2.2 DC Power Supply (B230).............................................................................................. 28
5.2.3 GPIB Interface (B10).....................................................................................................29
5.2.4 OCXO Reference Frequency (B4)................................................................................ 30
5.2.5 Universal DTV, ATV, FM Interface (B201)..................................................................... 30
5.2.6 Additional Interfaces (B5)..............................................................................................32
5.2.7 AV Decoder and TS Processing (B380)........................................................................33
5.2.8 MPEG Processing Board (B280).................................................................................. 34
5.2.9 Li-Ion Battery Pack (B235)............................................................................................ 35
6 Connecting the Instrument................................................................. 37
6.1 Preventing Electromagnetic Interference................................................................. 37
6.2 Connecting to the Power Supply...............................................................................38
6.2.1 Connecting to the AC Power Supply.............................................................................38
6.3 Connecting USB External Devices............................................................................ 39
6.3.1 External Keyboard.........................................................................................................39
6.3.2 Mouse........................................................................................................................... 40
6.3.3 Memory Stick................................................................................................................ 40
6.3.4 External Drive................................................................................................................40
7 Switching On or Off the Instrument................................................... 41
7.1 Instrument States........................................................................................................41
7.2 Switching On the Instrument..................................................................................... 42
7.3 Switching Off the Instrument..................................................................................... 42
7.3.1 Switching to Standby.....................................................................................................42
7.3.2 Switching Off................................................................................................................. 43

Contents
R&S®ETL
5Getting Started 2118.4130.02 ─ 04
7.4 Behavior of the ON/STANDBY Key............................................................................43
7.5 Checking the Provided Options.................................................................................44
7.6 Turn-On Tests.............................................................................................................. 45
7.6.1 Performing a Self-Alignment......................................................................................... 45
7.6.2 Performing a Self-Test...................................................................................................45
8 Sample Application..............................................................................46
8.1 Test Setup.................................................................................................................... 46
8.2 Setting the TV Analyzer/Receiver Mode....................................................................46
8.3 Performing the Measurement.................................................................................... 46
9 Operating the Instrument in a LAN.....................................................48
9.1 Computer Name.......................................................................................................... 48
9.2 IP Address................................................................................................................... 49
9.3 Connecting the Instrument to the Network...............................................................50
9.4 Connecting the Instrument to a Computer............................................................... 50
9.4.1 Windows 7 or Later....................................................................................................... 51
9.4.2 Other Operating Systems..............................................................................................51
9.5 Firewall Settings..........................................................................................................51
10 Installed Software................................................................................ 52
10.1 Operating System....................................................................................................... 52
10.1.1 Logon............................................................................................................................ 52
10.1.1.1 Automatic Logon........................................................................................................... 53
10.1.2 Access to Windows Settings......................................................................................... 54
10.2 Additional Software.................................................................................................... 54
10.3 Backup and Restore Application...............................................................................55
10.3.1 Creating a Backup.........................................................................................................57
10.3.2 Restoring a Selected Backup Version...........................................................................58
10.3.3 Deleting a Backup......................................................................................................... 58
11 Maintenance......................................................................................... 59
11.1 Recommended Calibration Interval...........................................................................59
11.2 Cleaning....................................................................................................................... 59

Contents
R&S®ETL
6Getting Started 2118.4130.02 ─ 04
11.3 Replacing the Fuses................................................................................................... 59
11.4 Storing..........................................................................................................................60
Index......................................................................................................61

Preface
R&S®ETL
7Getting Started 2118.4130.02 ─ 04
1 Preface
This chapter provides information related to safety issues and the product documenta-
tion.
1.1 For Your Safety
The R&S ETL is designated to develop, produce and verify electronic components and
devices in an industrial environment. An overview of its designated purpose is given in
Chapter 3, "System Overview", on page 12; details are provided throughout the prod-
uct documentation. Observe the operating conditions and performance limits stated in
the data sheet (specifications).
The product documentation helps you to use the R&S ETL safely and efficiently. Keep
the product documentation in a safe place and pass it on to the subsequent users.
Safety information is part of the product documentation. It warns you about the poten-
tial dangers and gives instructions how to prevent personal injury or damage caused
by dangerous situations. Safety information is provided as follows:
●In the "Basic Safety Instructions", safety issues are grouped according to subjects.
For example, one subject is electrical safety. The "Basic Safety Instructions" are
delivered with the R&S ETL in different languages.
●Throughout the documentation, safety instructions are provided when you need to
take care during setup or operation.
Always read the safety instructions carefully. Make sure to comply fully with them. Do
not take risks and do not underestimate the potential danger of small details such as a
damaged power cable.
1.2 Information Provided on the Instrument
The context-sensitive help provides quick user assistance, see Chapter 2.2, "User
Manuals and Help", on page 10.
The open source acknowledgment is stored in PDF format under:
C:\R_S\Instr\doc
On R&S ETLs with SSD/HDD, the product documentation in PDF format is also stored
there. On these R&S ETLs, you can display the PDFs using the Foxit Reader that is
already installed.
To update the PDFs
The PDFs provided on the R&S ETL originate from the date of delivery. For up-to-date
downloads, visit the product site described at:
Information Provided on the Instrument

Preface
R&S®ETL
8Getting Started 2118.4130.02 ─ 04
www.rohde-schwarz.com/product/etl
► If you install a new firmware version, the information in the C:\R_S\Instr\doc
directory is updated also.
1.3 Conventions Used in the Documentation
The following conventions are used throughout the product documentation.
Typography
Convention Description
"Graphical user interface elements" All names of graphical user interface elements on
the screen, such as dialogs, menus, options, but-
tons, and softkeys are enclosed by parentheses.
KEYS Key names are written in capital letters.
File names, commands, program code File names, commands, coding samples and screen
output are distinguished by their font.
Input Input to be entered by the user is displayed in italics.
Links Links are displayed in blue font.
"References" References to other parts of the documentation are
enclosed by parentheses.
Softkey descriptions
The description of a softkey (user manual and help) always starts with the softkey
name, and is followed by explaining text and one or more remote control commands.
Each remote command is placed in a single line.
Remote command descriptions
The description of remote control commands (user manual and help) always starts with
the command itself. It is followed by explaining text including an example, the charac-
teristics and the mode (standard or only with certain options). The remote commands
follow the SCPI syntax rules. All parts of the command that have to be entered are in
capital letters, the rest is added in small letters to complete the words and transport
their meaning.
Conventions for procedure descriptions
In manual operation, several alternative methods can be available to perform the same
task. If possible, the procedure using the front panel is described. Any elements that
can be activated by pressing a key can also be clicked using an also connected
mouse.
The alternative procedure using an external keyboard is only described if it deviates
from the standard operating procedures as described in the user manual, chapter
"Operating Concepts", or the help.
Conventions Used in the Documentation

Preface
R&S®ETL
9Getting Started 2118.4130.02 ─ 04
The terms "select" and "press" can refer to any of the described methods, for using a
key on the device or on a keyboard, or a mouse pointer in the display.
Conventions Used in the Documentation

Documentation Overview
R&S®ETL
10Getting Started 2118.4130.02 ─ 04
2 Documentation Overview
This chapter provides an overview of the R&S ETL user documentation. Unless speci-
fied otherwise, you find the documents on the R&S ETL product page at:
www.rohde-schwarz.com/manual/etl
2.1 Getting Started Manual
Introduces the R&S ETL and describes how to set up and start working with the prod-
uct. Includes a sample application and general information, e.g. safety instructions, etc.
A printed version is delivered with the instrument.
2.2 User Manuals and Help
Contains the description of all instrument modes and functions. Also provides an intro-
duction to remote control, a complete description of the remote control commands with
programming examples, and information on maintenance, instrument interfaces and
error messages. Includes the contents of the getting started manual.
The contents of the user manual is available as help in the R&S ETL. The help offers
quick, context-sensitive access to the complete information for the base unit and the
software options.
For detailed information on how to use the help, refer to "Operating Concepts".
Further information:
●Chapter 1.2, "Information Provided on the Instrument", on page 7
2.3 Tutorials
Tutorials offer guided examples and demonstrations on operating the R&S ETL. They
are provided on the product page of the internet.
2.4 Basic Safety Instructions
Contains safety instructions, operating conditions and further important information.
The printed document is delivered with the instrument.
Basic Safety Instructions

Documentation Overview
R&S®ETL
11Getting Started 2118.4130.02 ─ 04
2.5 Data Sheets and Brochures
The data sheet contains the technical specifications of the R&S ETL. It also lists the
options and their order numbers, and optional accessories.
The brochure provides an overview of the instrument and deals with the specific char-
acteristics.
See www.rohde-schwarz.com/brochure-datasheet/etl
2.6 Release Notes and Open Source Acknowledgment
(OSA)
The release notes list new features, improvements and known issues of the current
firmware version, and describe the firmware installation.
The open source acknowledgment document provides verbatim license texts of the
used open source software. On the R&S ETL, the open source acknowledgment docu-
ment is provided as PDF file in the same directory as the user manual.
See www.rohde-schwarz.com/firmware/etl
2.7 Application Notes, Application Cards, White Papers,
etc.
These documents deal with special applications or background information on particu-
lar topics.
See www.rohde-schwarz.com/application/etl
Application Notes, Application Cards, White Papers, etc.

System Overview
R&S®ETL
12Getting Started 2118.4130.02 ─ 04
3 System Overview
The R&S ETL TV analyzer stands for all-in-one. The R&S ETL combines the function-
ality of a TV and FM (radio) signal analyzer, a video and MPEG TS analyzer and a
spectrum analyzer in a single instrument. The R&S ETL also contains generators to
create analog video signals, audio signals and MPEG-2 transport streams.
The innovative instrument concept facilitates the flexible integration of demodulators
for analog and digital TV standards as well as sound broadcasting. All of the demodu-
lators work in realtime; fast signal processing allows comprehensive, extremely accu-
rate measurements.
Its wide range of functions and flexible configuration make the R&S ETL TV analyzer
the universal reference for the analysis of TV signals - for TV and cable network opera-
tors, transmitter manufacturers, service technicians and regulatory authorities.
The R&S ETL has primarily been designed to provide reproducible, high-quality analy-
sis of TV and sound broadcasting signals such as are needed at the transmitter site, at
the cable headend or for quality assurance during production.
The R&S ETL is ideal for both stationary and portable use. The compact, rugged hous-
ing makes outdoor use possible, e.g. for coverage measurements within a terrestrial
TV or sound broadcasting transmitter network.
Visit the product site (https://www.rohde-schwarz.com/product/etl/) for information on
available hardware and software options.

Setting Up the Instrument
R&S®ETL
13Getting Started 2118.4130.02 ─ 04
4 Setting Up the Instrument
Risk of injuries
To avoid injuries to yourself or others, always follow the instructions provided in the fol-
lowing chapters. Furthermore, observe the general safety instructions delivered with
the R&S ETL.
4.1 Unpacking the Instrument
The R&S ETL is shipped together with its mandatory accessories in a cardboard box.
4.1.1 Inspecting for Shipping Damage
Check the following. If anything is damaged, immediately notify the carrier.
1. Check the shipping container and cushioning material for damage.
2. Unpack the cardboard box, see Chapter 4.1.2, "Unpacking the Cardboard Box",
on page 13.
3. Check the housing and handle for visible damages or loose parts.
4.1.2 Unpacking the Cardboard Box
Proceed as follows:
1. Open the cardboard box.
2. Remove the accessories packed into the box.
3. Take the R&S ETL out of the packaging.
4. Remove the shock protectors attached to the R&S ETL.
Retain the original packing material. If the R&S ETL needs to be transported or ship-
ped later, you can use the material to prevent control elements and connectors from
being damaged. Rohde & Schwarz accepts claims of warranty only if the R&S ETL is
shipped with sufficient packaging.
Unpacking the Instrument

Setting Up the Instrument
R&S®ETL
14Getting Started 2118.4130.02 ─ 04
4.1.3 Checking the Accessories
The R&S ETL comes with the following accessories:
●Power cable
●Getting started manual
4.1.4 Warranty Conditions
For information on warranty conditions for the R&S ETL, refer to the terms of the deliv-
ery documents.
4.2 Putting Up the Instrument
The R&S ETL is designed for interior use only. For details on temperature range and
climatic loading, refer to the data sheet.
The R&S ETL can be used in standalone operation or can be installed in a rack.
Risk of material damage
Make sure that the following conditions are met at the operation site:
●The ambient temperature does not exceed the range specified in the data sheet.
●All fan openings are unobstructed and the airflow perforations are unimpeded. The
minimum distance from the wall is at least 10 cm.
Failure to meet these conditions can damage the R&S ETL or other devices in the test
setup.
If necessary, use proper protective equipment to protect DUTs against electrostatic dis-
charge caused by human contact.
4.2.1 Placing the Instrument on a Bench Top
Always place the R&S ETL on a stable, flat and level surface with the bottom of the
instrument facing down. The R&S ETL can be used in horizontal position, standing on
its feet, or propped up on the handle as described in "To adjust the handle position"
on page 15. Do not place anything on top of the R&S ETL, if the R&S ETL is not in a
level position. Keep in mind that the R&S ETL can cause injury to you or others if not
set up securely.
Putting Up the Instrument

Setting Up the Instrument
R&S®ETL
15Getting Started 2118.4130.02 ─ 04
Risk of injury when stacking instruments
A stack of instruments can tilt over and cause injury if not stacked correctly. Further-
more, the instruments at the bottom of the stack can be damaged due to the load
imposed by the instruments on top.
Observe the following instructions when stacking instruments:
●Place the bottom instrument on a stable, flat and level surface with the bottom of
the instrument facing down.
●Stack the instruments according to their size and weight, with the largest and heav-
iest instrument at the bottom.
●Never stack more than three instruments. If you need to stack more than three
instruments, install them in a rack.
To adjust the handle position
1. Pull at both side knobs and turn the handle as shown in Figure 4-1.
2. When the handle is in the desired position, loose your hold on both side knobs.
Figure 4-1: Moving the handle of the R&S ETL
Putting Up the Instrument

Setting Up the Instrument
R&S®ETL
16Getting Started 2118.4130.02 ─ 04
4.2.2 Mounting the Instrument in a Rack
The R&S ETL can be installed in a 19" rack mount by using a rack adapter kit (for
order no. see data sheet). Follow the installation instructions that are part of the
adapter kit.
Putting Up the Instrument

Interfaces and Connectors
R&S®ETL
17Getting Started 2118.4130.02 ─ 04
5 Interfaces and Connectors
This chapter describes the front panel and the rear panel of the R&S ETL, including all
function keys and connectors.
When using the interfaces and connectors, take care to avoid electromagnetic interfer-
ence. For details, see Chapter 6.1, "Preventing Electromagnetic Interference",
on page 37.
5.1 Front Panel
This chapter gives a short overview of the keys and connectors on the front panel.
A detailed description of the function keys and softkeys is provided in the user manual
or the help. For instructions on using the keys for operation and data entry, refer to the
user manual, chapter "Operating Concepts", or the help.
All connectors on the front panel are placed on the bottom of the right-hand side. The
inscriptions on your R&S ETL match the captions of the connector descriptions.
Figure 5-1: Front panel view
1 = On/standby key
2 = Keys for frequently-used functions
3 = Keys for operating softkeys
4 = Keys for changing softkey menus
5 = RUN key
6 = Keypad
7 = Rotary knob
8 = Cursor keys
Front Panel

Interfaces and Connectors
R&S®ETL
18Getting Started 2118.4130.02 ─ 04
9 = GEN OUT 50 Ω output
10 = USB interfaces
11 = AF OUT output
12 = RF IN 75 Ω input
13 = RF IN 50 Ω input
14 = Display
5.1.1 ON/STANDBY Key
See (1) in Figure 5-1.
The [ON/STANDBY] key works only if the AC power switch on the back of the
R&S ETL is switched on. It switches the R&S ETL from standby to on and back.
For details on switching on or off and the instrument states, refer to Chapter 7, "Switch-
ing On or Off the Instrument", on page 41.
5.1.2 Keys for Frequently-Used Functions
See (2) in Figure 5-1.
These basic functions are provided independently from the selected measurement
mode.
For detailed information, see the user manual or the help.
PRESET key
Sets a defined instrument state.
FILE key
Displays the softkeys of the file menu used for:
●Storing/loading instrument settings.
●Managing stored files.
SETUP key
Displays the softkeys of the setup menu used for basic instrument configuration:
●Frequency reference (ext/int), noise source, video/IF output (Additional Interfaces
option, R&S FSL-B5), transducer factors
●Date, time, display configuration
●LAN interface, remote control (GPIB Interface option, R&S FSL-B10)
●Self-alignment
●Firmware update and enabling of options
●Information about instrument configuration incl. firmware version and system error
messages
●Service support functions, for example self-test
Front Panel