Rohde & Schwarz ZVB 4 User manual

1145.1055.62-02
Quick Start Guide
Vector Network Analyzers
R&S®ZVB4 / ZVB8
1145.1010.04/05/06 / 08/09/10
Printed in the Federal
Republic of Germany
Test and Measurement Division

R&S®is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.

1145.1055.62 RE.1 E-2
Tabbed Divider Overview
R&S®ZVB Documentation Map
Data Sheet
Safety Instructions
Certificate of Quality
EU Certificate of Conformity
List of R&S Representatives
Glossary of Terms
Tabbed Divider
1 Chapter 1: Putting into Operation
2 Chapter 2: Getting Started
3 Chapter 3: System Overview
4 Index

1145.1055.62 RE.2 E-2
R&S®ZVB Documentation Map
Help System
The help system is embedded in the instrument, offering quick,
context-sensitive reference to the information needed for
operation and programming. The help contains the complete user
documentation for the network analyzer including the contents of
the present quick start guide.
You can also transfer the help file ZVB.chm to your PC and use it
as a standalone help.
Quick Start Guide
The present quick start guide describes everything that is needed
to put the instrument into operation and helps you to get familiar
with the analyzer. The quick start guide gives an introduction to
the instrument’s functionality and provides procedures for typical
measurement tasks.
Documentation CD-ROM
The CD-ROM provides the complete user documentation for the
network analyzer family:
•The online help system in two different HTML-based formats
(*.chm for transfer to the hard disk and WebHelp for viewing
from the CD).
•A printable (*.pdf) version of the online help.
•The quick start manual in printable form.
•Links to different useful sites in the R&S internet.
Optional Documentation
The printed version of the help system provides the contents of
the quick start manual plus the complete reference information for
operation and programming contained in the help. This manual
can be ordered as an option (stock no. 1155.1084.12); see
ordering information in the data sheet. Besides the CD-ROM
contains a *.pdf version of the manual.

Safety Instructions
095.1000 Sheet 17
This unit has been designed and tested in accordance with the EC Certificate of Conformity and has left the
manufacturer’s plant in a condition fully complying with safety standards.
To maintain this condition and to ensure safe operation, the user must observe all instructions and warnings
given in this operating manual.
Safety-related symbols used on equipment and documentation from R&S:
Observe
operating
instructions
Weight
indication for
units >18 kg
PE terminal Ground
terminal Danger! Shock hazard Warning! Hot surfaces Ground Attention!
Electrostatic
sensitive de-
vices require
special care
1. The unit may be used only in the operating con-
ditions and positions specified by the manufac-
turer. Unless otherwise agreed, the following
applies to R&S products:
IP degree of protection 2X, pollution severity 2
overvoltage category 2, only for indoor use, al-
titude max. 2000 m.
The unit may be operated only from supply net-
works fused with max. 16 A.
Unless specified otherwise in the data sheet, a
tolerance of ±10% shall apply to the nominal
voltage and of ±5% to the nominal frequency.
2. For measurements in circuits with voltages Vrms
> 30 V, suitable measures should be taken to
avoid any hazards.
(using, for example, appropriate measuring
equipment, fusing, current limiting, electrical
separation, insulation).
3. If the unit is to be permanently wired, the PE
terminal of the unit must first be connected to
the PE conductor on site before any other con-
nections are made. Installation and cabling of
the unit to be performed only by qualified techni-
cal personnel.
4. For permanently installed units without built-in
fuses, circuit breakers or similar protective de-
vices, the supply circuit must be fused such as
to provide suitable protection for the users and
equipment.
5. Prior to switching on the unit, it must be ensured
that the nominal voltage set on the unit matches
the nominal voltage of the AC supply network.
If a different voltage is to be set, the power fuse
of the unit may have to be changed accordingly.
6. Units of protection class I with disconnectible
AC supply cable and appliance connector may
be operated only from a power socket with
earthing contact and with the PE conductor con-
nected.
7. It is not permissible to interrupt the PE conduc-
tor intentionally, neither in the incoming cable
nor on the unit itself as this may cause the unit
to become electrically hazardous.
Any extension lines or multiple socket outlets
used must be checked for compliance with rele-
vant safety standards at regular intervals.
8. If the unit has no power switch for disconnection
from the AC supply, the plug of the connecting
cable is regarded as the disconnecting device.
In such cases it must be ensured that the power
plug is easily reachable and accessible at all
times (length of connecting cable approx. 2 m).
Functional or electronic switches are not suit-
able for providing disconnection from the AC
supply.
If units without power switches are integrated in
racks or systems, a disconnecting device must
be provided at system level.
9. Applicable local or national safety regulations
and rules for the prevention of accidents must
be observed in all work performed.
Prior to performing any work on the unit or
opening the unit, the latter must be discon-
nected from the supply network.
Any adjustments, replacements of parts, main-
tenance or repair may be carried out only by
authorized R&S technical personnel.
continued overleaf

Safety Instructions
095.1000 Sheet 18
Only original parts may be used for replacing
parts relevant to safety (eg power switches,
power transformers, fuses). A safety test must
be performed after each replacement of parts
relevant to safety.
(visual inspection, PE conductor test, insulation-
resistance, leakage-current measurement, func-
tional test).
10. Ensure that the connections with information
technology equipment comply with IEC950 /
EN60950.
11. Lithium batteries must not be exposed to high
temperatures or fire.
Keep batteries away from children.
If the battery is replaced improperly, there is
danger of explosion. Only replace the battery by
R&S type (see spare part list).
Lithium batteries are suitable for environmen-
tally-friendly disposal or specialized recycling.
Dispose them into appropriate containers, only.
Do not short-circuit the battery.
12. Equipment returned or sent in for repair must be
packed in the original packing or in packing with
electrostatic and mechanical protection.
13. Electrostatics via the connectors may dam-
age the equipment. For the safe handling and
operation of the equipment, appropriate
measures against electrostatics should be im-
plemented.
14. The outside of the instrument is suitably
cleaned using a soft, lint-free dustcloth. Never
use solvents such as thinners, acetone and
similar things, as they may damage the front
panel labeling or plastic parts.
15. Any additional safety instructions given in this
manual are also to be observed.

Qualitätszertifikat
Sehr geehrter Kunde,
Sie haben sich für den Kauf eines Rohde &
Schwarz-Produktes entschieden. Hiermit
erhalten Sie ein nach modernsten Ferti-
gungsmethoden hergestelltes Produkt. Es
wurde nachden Regeln unseresQualitäts-
managementsystems entwickelt, gefer-
tigt und geprüft. Das Rohde & Schwarz-
Qualitätsmanagementsystemistu.a.nach
ISO 9001 und ISO14001 zertifiziert.
Certificate of quality
Dear Customer,
You have decided to buy a Rohde &
Schwarz product. You are thus assured of
receiving a product that is manufactured
using the most modern methods available.
This product was developed, manufac-
tured and tested in compliance with our
quality management system standards.
The Rohde & Schwarz quality manage-
ment system is certified according to stan-
dards such as ISO9001 and ISO14001.
Certificat de qualité
Cher client,
Vous avez choisi d'acheter un produit
Rohde & Schwarz. Vous disposez donc
d'un produit fabriqué d'après les métho-
des les plus avancées. Le développement,
la fabrication et les tests respectent nos
normes de gestion qualité. Le système de
gestion qualité de Rohde & Schwarz a été
homologué, entre autres, conformément
aux normes ISO 9001 et ISO14001.
Certified Quality System
ISO 9001
Certified Environmental System
ISO 14001
DQS REG. NO 1954 QM
DQS REG. NO 1954 UM

1145.1010.01 CE E-1
EC Certificate of Conformity
Certificate No.: 2004-17
This is to certify that:
Equipment type Stock No. Designation
ZVB4 1145.1010.04/.05/.06 Vector Network Analyzer
ZVB8 1145.1010.08/.09/.10
complies with the provisions of the Directive of the Council of the European Union on the
approximation of the laws of the Member States
- relating to electrical equipment for use within defined voltage limits
(73/23/EEC revised by 93/68/EEC)
- relating to electromagnetic compatibility
(89/336/EEC revised by 91/263/EEC, 92/31/EEC, 93/68/EEC)
Conformity is proven by compliance with the following standards:
EN61010-1 : 2001-12
EN55011 : 1998 + A1:1999 + A2:2002
EN61326 : 1997 + A1:1998 + A2:2001
For the assessment of electromagnetic compatibility, the limits of radio interference for Class
B equipment as well as the immunity to interference for operation in industry have been used
as a basis.
Affixing the EC conformity mark as from 2004
ROHDE & SCHWARZ GmbH & Co. KG
Mühldorfstr. 15, D-81671 München
Munich, 2004-05-07 Central Quality Management FS-QZ / Becker