Rohde & Schwarz SMB100A User manual

R&S®SMB100A
RF and Microwave Signal Generator
Quick Start Guide
1407081262
Version 20
(>78<Ì)

This document describes the R&S®SMB100A, stock no. 1406.6000K02/K03 and its options.
© 2022 Rohde & Schwarz GmbH & Co. KG
Muehldorfstr. 15, 81671 Muenchen, Germany
Phone: [phone] - 0
Email: [email protected]
Internet: www.rohde-schwarz.com
Subject to change – data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
1407.0812.62 | Version 20 | R&S®SMB100A
The following abbreviations are used throughout this manual: R&S®SMB100A is abbreviated as R&S SMB, Linux® is abbreviated as
Linux.

Contents
R&S®SMB100A
3Quick Start Guide 1407.0812.62 ─ 20
Contents
1 Safety and Regulatory Information...................................................... 7
1.1 Safety instructions........................................................................................................7
1.2 Labels on R&S SMB......................................................................................................9
1.3 Warning Messages in the Documentation................................................................ 10
1.4 Korea certification class B......................................................................................... 10
2 Documentation overview.....................................................................11
2.1 User manual and help................................................................................................. 11
2.2 Data sheets and brochures........................................................................................ 11
2.3 Release notes and open source acknowledgment (OSA)....................................... 11
2.4 Application notes, application cards, white papers, etc......................................... 12
3 Key Features.........................................................................................13
4 Preparing for Use.................................................................................14
4.1 Lifting and Carrying.................................................................................................... 14
4.2 Unpacking and Checking........................................................................................... 14
4.3 Choosing the Operating Site......................................................................................14
4.4 Setting Up the R&S SMB............................................................................................ 15
4.4.1 Placing the R&S SMB on a Bench Top......................................................................... 15
4.4.2 Mounting the R&S SMB in a Rack................................................................................ 16
4.5 Considerations for Test Setup................................................................................... 17
4.6 Connecting to Power.................................................................................................. 18
4.7 Connecting to LAN......................................................................................................18
4.8 Connecting to IEC 625/IEEE 488 (GPIB)....................................................................19
4.9 Connecting USB Devices........................................................................................... 19
4.10 Connecting to RF........................................................................................................ 20
4.11 Connecting to Ref In/Ref Out..................................................................................... 21
4.12 Switching On or Off.................................................................................................... 21
4.13 Default Settings...........................................................................................................23
4.14 Working with Linux Operating System..................................................................... 24
4.15 Setting Up a Network (LAN) Connection...................................................................24
4.15.1 Assigning the IP Address.............................................................................................. 24

Contents
R&S®SMB100A
4Quick Start Guide 1407.0812.62 ─ 20
4.15.2 Using Computer Names................................................................................................26
4.16 Remote Access via an External Controller...............................................................26
4.16.1 Using a Web Browser for Remote Access.................................................................... 28
4.16.2 Remote Access via a VNC Client Software.................................................................. 29
4.17 LXI Configuration........................................................................................................ 33
4.17.1 LXI Browser Settings.....................................................................................................34
4.17.2 LAN Configuration.........................................................................................................36
5 Instrument Tour....................................................................................43
5.1 Front Panel Tour..........................................................................................................43
5.1.1 Utility Keys.................................................................................................................... 43
5.1.2 Standby LEDs and Standby Key...................................................................................44
5.1.3 Display.......................................................................................................................... 44
5.1.4 Setup Keys....................................................................................................................45
5.1.5 Keypad for data entry....................................................................................................46
5.1.6 Rotary Knob and Navigation Keys................................................................................ 47
5.1.7 Front Panel Connectors................................................................................................ 48
5.2 Rear Panel Tour........................................................................................................... 49
5.2.1 Description of the Connectors.......................................................................................50
6 Trying out the Instrument....................................................................53
7 System Overview................................................................................. 58
7.1 Brief Introduction to the Instrument's Concept....................................................... 58
7.2 Signal Flow at a Glance.............................................................................................. 58
7.3 Application Field of the Instrument...........................................................................59
7.4 Description of Individual Diagram Blocks................................................................ 59
8 Instrument Control...............................................................................62
8.1 Manual Operation........................................................................................................62
8.1.1 Legend of Manual Controls........................................................................................... 62
8.1.2 Key Elements................................................................................................................ 65
8.1.3 Display.......................................................................................................................... 67
8.1.4 Accessing Dialogs.........................................................................................................72
8.1.5 Setting Parameters....................................................................................................... 73
8.1.6 Editors........................................................................................................................... 80

Contents
R&S®SMB100A
5Quick Start Guide 1407.0812.62 ─ 20
8.1.7 How to Use the Help System........................................................................................ 81
8.1.8 File Management.......................................................................................................... 83
8.1.9 Legend of Front-Panel Controls.................................................................................... 86
8.2 Remote Control........................................................................................................... 88
8.3 Remote Access........................................................................................................... 89
9 Contacting customer support.............................................................90
Index......................................................................................................91

Contents
R&S®SMB100A
6Quick Start Guide 1407.0812.62 ─ 20

Safety and Regulatory Information
R&S®SMB100A
7Quick Start Guide 1407.0812.62 ─ 20
1 Safety and Regulatory Information
The product documentation helps you use the product safely and efficiently. Follow the
instructions provided here and in the following chapters.
Intended use
The product is intended for the development, production and verification of electronic
components and devices in industrial, administrative, and laboratory environments.
Use the product only for its designated purpose. Observe the operating conditions and
performance limits stated in the data sheet.
Where do I find safety information?
Safety information is part of the product documentation. It warns you of potential dan-
gers and gives instructions on how to prevent personal injury or damage caused by
dangerous situations. Safety information is provided as follows:
●In Safety instructions. The same information is provided in many languages as
printed "Safety Instructions". The printed "Safety Instructions" are delivered with
the product.
●Throughout the documentation, safety instructions are provided when you need to
take care during setup or operation.
1.1 Safety instructions
Products from the Rohde & Schwarz group of companies are manufactured according
to the highest technical standards. To use the products safely, follow the instructions
provided here and in the product documentation. Keep the product documentation
nearby and offer it to other users.
Use the product only for its intended use and within its performance limits. Intended
use and limits are described in the product documentation such as the data sheet,
manuals and the printed "Safety Instructions". If you are unsure about the appropriate
use, contact Rohde & Schwarz customer service.
Using the product requires specialists or specially trained personnel. These users also
need sound knowledge of at least one of the languages in which the user interfaces
and the product documentation are available.
Never open the casing of the product. Only service personnel authorized by
Rohde & Schwarz are allowed to repair the product. If any part of the product is dam-
aged or broken, stop using the product. Contact Rohde & Schwarz customer service at
http://www.customersupport.rohde-schwarz.com.
Lifting and carrying the product
The maximum weight of the product is provided in the data sheet. To move the product
safely, you can use lifting or transporting equipment such as lift trucks and forklifts. Fol-
low the instructions provided by the equipment manufacturer.
Safety instructions

Safety and Regulatory Information
R&S®SMB100A
8Quick Start Guide 1407.0812.62 ─ 20
Choosing the operating site
Only use the product indoors. The product casing is not waterproof. Water that enters
can electrically connect the casing with live parts, which can lead to electric shock,
serious personal injury or death if you touch the casing. If Rohde & Schwarz provides
accessories designed for your product, e.g. a carrying bag, you can use the product
outdoors.
Unless otherwise specified, you can operate the product up to an altitude of 2000 m
above sea level. The product is suitable for pollution degree 2 environments where
nonconductive contamination can occur. For more information on environmental condi-
tions such as ambient temperature and humidity, see the data sheet.
Setting up the product
Always place the product on a stable, flat and level surface with the bottom of the prod-
uct facing down. If the product is designed for different positions, secure the product so
that it cannot fall over.
If the product has foldable feet, always fold the feet completely in or out to ensure sta-
bility. The feet can collapse if they are not folded out completely or if the product is
moved without lifting it. The foldable feet are designed to carry the weight of the prod-
uct, but not an extra load.
If stacking is possible, keep in mind that a stack of products can fall over and cause
injury.
If you mount products in a rack, ensure that the rack has sufficient load capacity and
stability. Observe the specifications of the rack manufacturer. Always install the prod-
ucts from the bottom shelf to the top shelf so that the rack stands securely. Secure the
product so that it cannot fall off the rack.
Connecting to power
The product is an overvoltage category II product. Connect the product to a fixed
installation used to supply energy-consuming equipment such as household applian-
ces and similar loads. Keep in mind that electrically powered products have risks, such
as electric shock, fire, personal injury or even death.
Take the following measures for your safety:
●Before switching on the product, ensure that the voltage and frequency indicated
on the product match the available power source. If the power adapter does not
adjust automatically, set the correct value and check the rating of the fuse.
●If a product has an exchangeable fuse, its type and characteristics are indicated
next to the fuse holder. Before changing the fuse, switch off the product and dis-
connect it from the power source. How to change the fuse is described in the prod-
uct documentation.
●Only use the power cable delivered with the product. It complies with country-spe-
cific safety requirements. Only insert the plug into an outlet with protective conduc-
tor terminal.
●Only use intact cables and route them carefully so that they cannot be damaged.
Check the power cables regularly to ensure that they are undamaged. Also ensure
that nobody can trip over loose cables.
Safety instructions

Safety and Regulatory Information
R&S®SMB100A
9Quick Start Guide 1407.0812.62 ─ 20
●If the product needs an external power supply, use the power supply that is deliv-
ered with the product or that is recommended in the product documentation or a
power supply that conforms to the country-specific regulations.
●Only connect the product to a power source with a fuse protection of maximum
20 A.
●Ensure that you can disconnect the product from the power source at any time.
Pull the power plug to disconnect the product. The power plug must be easily
accessible. If the product is integrated into a system that does not meet these
requirements, provide an easily accessible circuit breaker at the system level.
Cleaning the product
Use a dry, lint-free cloth to clean the product. When cleaning, keep in mind that the
casing is not waterproof. Do not use liquid cleaning agents.
Meaning of safety labels
Safety labels on the product warn against potential hazards.
Potential hazard
Read the product documentation to avoid personal injury or product damage.
Electrical hazard
Indicates live parts. Risk of electric shock, fire, personal injury or even death.
Hot surface
Do not touch. Risk of skin burns. Risk of fire.
Protective conductor terminal
Connect this terminal to a grounded external conductor or to protective ground. This connec-
tion protects you against electric shock if an electric problem occurs.
1.2 Labels on R&S SMB
Labels on the casing inform about:
●Personal safety, see "Connecting to power" on page 8.
●Product and environment safety, see Table 1-1.
●Identification of the product, see the serial number on the rear panel.
Table 1-1: Labels regarding R&S
SMB and environment safety
Labeling in line with EN 50419 for disposal of electrical and electronic equipment after the prod-
uct has come to the end of its service life. For more information, see the product user manual,
chapter "Disposal".
Labels on R&S SMB

Safety and Regulatory Information
R&S®SMB100A
10Quick Start Guide 1407.0812.62 ─ 20
1.3 Warning Messages in the Documentation
A warning message points out a risk or danger that you need to be aware of. The sig-
nal word indicates the severity of the safety hazard and how likely it will occur if you do
not follow the safety precautions.
WARNING
Potentially hazardous situation. Could result in death or serious injury if not avoided.
CAUTION
Potentially hazardous situation. Could result in minor or moderate injury if not avoided.
NOTICE
Potential risks of damage. Could result in damage to the supported product or to other
property.
1.4 Korea certification class B
이 기기는 가정용(B급) 전자파 적합기기로서 주로 가정에서 사용하는 것을 목적으로 하
며, 모든 지역에서 사용할 수 있습니다.
Korea certification class B

Documentation overview
R&S®SMB100A
11Quick Start Guide 1407.0812.62 ─ 20
2 Documentation overview
This section provides an overview of the R&S SMB user documentation. Unless speci-
fied otherwise, you find the documents on the R&S SMB product page at:
www.rohde-schwarz.com/manual/smb100a
2.1 User manual and help
Contains the description of all instrument modes and functions. It also provides an
introduction to remote control, a complete description of the remote control commands
with programming examples, and information on maintenance, instrument interfaces
and error messages. Includes the contents of the quick start guide manual.
The contents of the user manuals are available as help in the R&S SMB. The help
offers quick, context-sensitive access to the complete information.
All user manuals are also available for download or for immediate display on the Inter-
net.
2.2 Data sheets and brochures
The data sheet contains the technical specifications of the R&S SMB. It also lists the
options and their order numbers and optional accessories.
The brochure provides an overview of the instrument and deals with the specific char-
acteristics.
See www.rohde-schwarz.com/brochure-datasheet/smb100a
2.3 Release notes and open source acknowledgment
(OSA)
The release notes list new features, improvements and known issues of the current
firmware version, and describe the firmware installation.
The open source acknowledgment document provides verbatim license texts of the
used open source software.
See www.rohde-schwarz.com/firmware/smb100a
Release notes and open source acknowledgment (OSA)

Documentation overview
R&S®SMB100A
12Quick Start Guide 1407.0812.62 ─ 20
2.4 Application notes, application cards, white papers,
etc.
These documents deal with special applications or background information on particu-
lar topics.
See www.rohde-schwarz.com/application/smb100a.
Application notes, application cards, white papers, etc.

Key Features
R&S®SMB100A
13Quick Start Guide 1407.0812.62 ─ 20
3 Key Features
The R&S SMB is a new high-performance signal generator developed to meet
demanding customer requirements. Offering excellent signal characteristic and
straightforward and intuitive operation, the signal generator makes signal generation
fast and easy.
Outstanding key features of the R&S SMB are:
●Frequency range from 100 kHz to up to 40 GHz
●SSB phase noise of –108 dBc (typ.) at 10 GHz and 20 kHz offset
●Wideband noise of –138 dBc at 10 GHz and 30 MHz offset
●High output power of up to +27 dBm (meas.)
●Analog modulations with AM, FM/φM and pulse modulation
For more information, see data sheet.

Preparing for Use
R&S®SMB100A
14Quick Start Guide 1407.0812.62 ─ 20
4 Preparing for Use
Here, you can find basic information about setting up the product for the first time.
4.1 Lifting and Carrying
See "Lifting and carrying the product" on page 7.
► Use the carrying handle at the side for lifting and carrying the R&S SMB.
For mounting the R&S SMB in a rack, see Chapter 4.4.2, "Mounting the R&S SMB in a
Rack", on page 16.
4.2 Unpacking and Checking
1. Unpack the R&S SMB carefully.
2. Retain the original packing material. Use it to protect the control elements and con-
nectors when transporting or shipping the R&S SMB later.
See also chapter "Transporting" in the operating manual.
3. Using the delivery notes, check the equipment for completeness.
4. Check the equipment for damage.
If the delivery is incomplete or equipment is damaged, contact Rohde & Schwarz.
4.3 Choosing the Operating Site
Specific operating conditions ensure proper operation and avoid damage to the prod-
uct and connected devices. For information on environmental conditions such as ambi-
ent temperature and humidity, see the data sheet.
See also "Choosing the operating site" on page 8.
Electromagnetic compatibility classes
The electromagnetic compatibility (EMC) class indicates where you can operate the
product. The EMC class of the product is given in the data sheet.
●Class B equipment is suitable for use in:
– Residential environments
– Environments that are directly connected to a low-voltage supply network that
supplies residential buildings
Choosing the Operating Site

Preparing for Use
R&S®SMB100A
15Quick Start Guide 1407.0812.62 ─ 20
●Class A equipment is intended for use in industrial environments. It can cause
radio disturbances in residential environments due to possible conducted and radi-
ated disturbances. It is therefore not suitable for class B environments.
If class A equipment causes radio disturbances, take appropriate measures to
eliminate them.
4.4 Setting Up the R&S SMB
See also:
●"Setting up the product" on page 8
●"Intended use" on page 7
4.4.1 Placing the R&S SMB on a Bench Top
To place the product on a bench top
1. Place the product on a stable, flat and level surface. Ensure that the surface can
support the weight of the product. For information on the weight, see the data
sheet.
2. CAUTION! Foldable feet can collapse. See "Setting up the product" on page 8.
Always fold the feet completely in or out. With folded-out feet, do not place any-
thing on top or underneath the product.
3. WARNING! A stack of products can fall over and cause injury. Never stack more
than three products on top of each other. Instead, mount them in a rack.
Stack as follows:
● If the products have foldable feet, fold them in completely.
● It is best if all products have the same dimensions (width and length). If the
products have different dimensions, stack according to size and place the
smallest product on top.
● Do not exceed the permissible total load placed on the product at the bottom of
the stack:
– 50 kg when stacking products of identical dimensions (left figure).
– 25 kg when stacking smaller products on top (middle figure).
Setting Up the R&S SMB

Preparing for Use
R&S®SMB100A
16Quick Start Guide 1407.0812.62 ─ 20
Left = Stacked correctly, same dimensions
Middle = Stacked correctly, different dimensions
Right = Stacked incorrectly, too many products
4. NOTICE! Overheating can damage the product.
Prevent overheating as follows:
● Keep a minimum distance of 10 cm between the fan openings of the product
and any object in the vicinity.
● Do not place the product next to heat-generating equipment such as radiators
or other products.
4.4.2 Mounting the R&S SMB in a Rack
To prepare the rack
1. Observe the requirements and instructions in "Setting up the product" on page 8.
2. NOTICE! Insufficient airflow can cause overheating and damage the product.
Design and implement an efficient ventilation concept for the rack.
To mount the R&S SMB in a rack
1. Use an adapter kit that fits the dimensions of the R&S SMB to prepare the instru-
ment for rack mounting.
a) Order the rack adapter kit designed for the R&S SMB. For the order number,
see the data sheet.
b) Mount the adapter kit. Follow the assembly instructions provided with the
adapter kit.
2. Lift the R&S SMB to shelf height.
3. Push the R&S SMB onto the shelf until the rack brackets fit closely to the rack.
4. Tighten all screws at the rack brackets with a tightening torque of 1.2 Nm to secure
the R&S SMB in the rack.
Setting Up the R&S SMB

Preparing for Use
R&S®SMB100A
17Quick Start Guide 1407.0812.62 ─ 20
To unmount the R&S SMB from a rack
1. Loosen the screws at the rack brackets.
2. Remove the R&S SMB from the rack.
3. If placing the R&S SMB on a bench top again, unmount the adapter kit from the
R&S SMB. Follow the instructions provided with the adapter kit.
4.5 Considerations for Test Setup
Cable selection and electromagnetic interference (EMI)
Electromagnetic interference (EMI) can affect the measurement results.
To suppress electromagnetic radiation during operation:
●Use high-quality shielded cables, especially for the following connector types:
– BNC
Double-shielded BNC cables.
How to: "To connect to non-screwable connectors (BNC)" on page 20
– USB
Double-shielded USB cables.
How to: Chapter 4.9, "Connecting USB Devices", on page 19.
See chapter "Troubleshooting and Error Messages > Measuring USB Cable
Quality" in the operating manual.
– LAN
At least CAT6 STP cables.
How to: Chapter 4.7, "Connecting to LAN", on page 18
●Always terminate open cable ends.
●Ensure that connected external devices comply with EMC regulations.
Signal input and output levels
Information on signal levels is provided in the data sheet. Keep the signal levels within
the specified ranges to avoid damage to the R&S SMB and connected devices.
Preventing electrostatic discharge (ESD)
Electrostatic discharge is most likely to occur when you connect or disconnect a DUT.
►NOTICE! Electrostatic discharge can damage the electronic components of the
product and the device under test (DUT).
Ground yourself to prevent electrostatic discharge damage:
a) Use a wrist strap and cord to connect yourself to ground.
b) Use a conductive floor mat and heel strap combination.
Considerations for Test Setup

Preparing for Use
R&S®SMB100A
18Quick Start Guide 1407.0812.62 ─ 20
4.6 Connecting to Power
For safety information, see "Connecting to power" on page 8.
If there were any problems duirng power on, check the condition of the mains fuses as
described under "Maintenance, Storage and Disposal > Changing Fuses" in the oper-
ating manual.
To connect the R&S SMB to power:
1. Plug the AC power cable into the AC power connector at the rear panel of the
instrument. Only use the AC power cable delivered with the R&S SMB.
2. Plug the AC power cable into a power outlet with ground contact.
The required ratings are listed next to the AC power connector and in the data
sheet.
4.7 Connecting to LAN
Network environment
Before connecting the product to a local area network (LAN), consider the following:
●Install the latest firmware to reduce security risks.
●For internet or remote access, use secured connections if applicable.
●Ensure that the network settings comply with the security policies of your company.
Contact your local system administrator or IT department before connecting your
product to your company LAN.
●When connected to the LAN, the product may potentially be accessed from the
internet, which may be a security risk. For example, attackers might misuse or
damage the product.
To connect to LAN
The "LAN" connector is at the rear panel.
► Connect the LAN socket with an RJ-45 cable to the LAN.
By default, the R&S SMB is configured to use DHCP (dynamic host configuration pro-
tocol) and no static IP address is configured.
If switched on and connected to the LAN, you can find the address information in the
network settings dialog.
See "Instrument Function > General Instrument Settings > General Configuration of
Instrument - Setup Key > Network Settings" in the operating manual.
Connecting to LAN

Preparing for Use
R&S®SMB100A
19Quick Start Guide 1407.0812.62 ─ 20
4.8 Connecting to IEC 625/IEEE 488 (GPIB)
To connect to the IEC 625/IEEE 488 interface
You can use the GPIB bus interface for controlling the instrument remotely. The "IEC
625/IEEE 488" connector is at the rear panel.
1. Connect the "IEC 625/IEEE 488" socket to the controller PC with a double-shielded
GPIB bus interface cable.
2. Configure the settings for remote control over GPIB.
The controller must address the instrument with the GPIB bus address.
For details, refer to "Remote Control Basics > Remote Control Interfaces and Pro-
tocols > GPIB Interface (IEC/IEEE Bus Interface" and "Hardware Interfaces" in the
operating manual.
4.9 Connecting USB Devices
You can connect or disconnect USB devices, e.g., memory stick, a CD-ROM keyboard,
etc, with the R&S SMB during operation.
To connect a USB device to the interface of the R&S SMB, always use the USB type A
connector t the rear panel. Refer to the documentation of the USB device to find out
which USB connector type you can connect to the USB device.
To connect USB storage devices
USB storage devices, such as memory sticks, allow easy data transfer from/to the
R&S SMB. You can also use them for firmware updates.
► Connect the USB storage device to the USB type A connector at the rear panel.
To connect USB devices with external power supply
1. NOTICE! Connected devices with external power supply can feed back current into
the 5 V power supply of the USB interface and thus damage the R&S SMB.
Ensure that there is no connection between the positive pole of the power supply
and the +5 V power pin of the USB interface (VBUS).
2. Connect the USB storage device to the USB type A connector at the rear panel.
To connect a keyboard
► Connect the keyboard to the USB type A connector at the rear panel.
When connected, the R&S SMB detects the keyboard automatically. A detected
keyboard has the default layout English – US.
Use the "Setup > Keyboard Settings" dialog to configure the keyboard properties.
Connecting USB Devices

Preparing for Use
R&S®SMB100A
20Quick Start Guide 1407.0812.62 ─ 20
To connect a mouse
► Connect the keyboard to the USB type A connector at the rear panel.
When connected, the R&S SMB detects the mouse automatically.
To connect power sensors
You can also connect power sensors of the R&S NRP series either directly at the USB
interface, or using an USB hub, e.g. R&S NRP-Z5 with several connected power sen-
sors.
For sensors with network capabilitiy, you can use the LAN interface, see
► To connect a power senor to the USB type A connector, you have several options:
● Connect the sensor to the USB type A connector
If necessary, use an adapter cable, e.g. R&S NRP-Z3 or R&S NRP-Z4
● Connect several sensors to an USB hub, and the hub to the R&S SMB.
See chapter "RF Measurement" in the operating manual.
4.10 Connecting to RF
The "RF" connector is at the front panel.
To prepare for connecting to RF
1. NOTICE! Damaged or not clean connections can lead to RF insertion loss and mis-
match, and even premature wear of the connectors.
Before connecting to the port, inspect the RF connector visually to check that it is
clean, undamaged and mechanically compatible.
See the application note 1MA99 for information on how to handle and maintain the
RF port, to minimize measurement deviations and ensure its longevity.
2. NOTICE! Risk of instrument damage. Excessive reverse power or DC voltage at
the RF connector can damage the instrument.
Make sure that the values do not exceed the reverse power and DC limits as given
in the data sheet.
3. If the R&S SMB is switched on, deactivate the RF output, before connecting an RF
cable to the RF connector.
In the home screen, select the block "Level" > "RF ON > Off".
To connect to non-screwable connectors (BNC)
1. Use a high-quality RF cable that matches the RF connector type.
See "Cable selection and electromagnetic interference (EMI)" on page 17.
2. To connect the RF cable with the RF connector, proceed as follows:
a) Carefully align the connector of the cable and the RF connector along a com-
mon axis.
Connecting to RF