Roland Aerophone Pro Editor User manual

© 2020 Roland Corporation
Aerophone Pro Editor
Owner’s Manual
04

Aerophone Pro Editor
Contents
Preparing to Use Aerophone Pro Editor
Connecting with the Aerophone
About Aerophone Pro Editor
Using FAVORITE
Using the FAVORITE Screen
Using EDITOR
Setting the Parameter Values
Turning all effects off
Using the EDITOR Screen
SCENE VIEW
PART VIEW
TONE VIEW
PARTIAL VIEW
Using LIBRARIAN
Using the LIBRARIAN Screen
Using the SCENE LIST Screen
Importing a Scene from the Aerophone into LIBRARIAN
Exporting a Scene from LIBRARIAN into the Aerophone
Exporting the Libraries from LIBRARIAN to a Mobile Device or
Cloud Service
Importing a Scene from a Mobile Device or Cloud Service to
LIBRARIAN
Using SETUP

Contents
Preparing to Use Aerophone Pro Editor
Connect the “Aerophone Pro Editor” app installed on your mobile
device to the Aerophone via Bluetooth.
* When using on Android 6.0 or later, please turn Android Location mode on.
Connecting with the Aerophone
1.
Turn the Aerophone on.
The power LED (orange) is lit.
2.
Place the Aerophone you want to connect close to your mobile
device.
MEMO
5 Make sure that the Bluetooth LED (blue) on the Aerophone is lit. If the LED is
o, the Bluetooth function has been turned o. Set “Bluetooth” to “On” from
the [MENU] button.
5 If you have more than one Aerophone unit, power-on only the unit that you
want to connect (turn o the power of the other units).
3.
Turn on the Bluetooth function of your mobile device.
NOTE
Do not tap the “AE-30”indication that appears in the Bluetooth settings of your
mobile device. If you tapped this, temporarily cancel the device registration,
and perform the procedure again from step 1.

Contents
Preparing to Use Aerophone Pro Editor
4.
Start Aerophone Pro Editor.
5.
Tap the [CONNECT] button on the screen.
* If more than one Aerophone is detected, a selection screen appears.
* If the mobile device was already connected to an Aerophone, it automatically connects to
that unit again, even if more than one Aerophone is detected.
6.
If the pairing conrmation screen appears, tap“Pair.”
Once connected, the message“Connected to Aerophone”is shown
in the app.
7.
Tap the [OK] button.

Contents
About Aerophone Pro Editor
Aerophone Pro Editor has the following functions.
To switch between functions, use the buttons at the bottom of the
screen.
EDITOR
Use this to get an overview of
the sound settings, or to edit the
scene/tone parameters.
& “Using EDITOR”
FAVORITE
Lets you check and switch
between the currently
selected scene, or register
and switch between favorite
scenes.
& “Using FAVORITE”
STATUS
Shows the connection status
with the Aerophone and
its power status (whether
using an AC adapter, and
how much battery power
remains).
Not connected
Connected
(AC adaptor)
Connected
(battery power)
* Remaining battery
power is displayed
in ve levels.
* Tap the icon to show the
screen for connecting with the
corresponding Aerophone.
SETUP
Congures the connection
settings with the Aerophone,
and shows the Owner’s
Manual (this document).
& “Using SETUP”
LIBRARIAN
You can manage sets (libraries) of scenes in the
Aerophone.
Libraries support the import and export of user
scenes, and can be used to save the scenes as les
to your mobile device or to a cloud service.
A library can contain up to 50 scenes, and up to 20
libraries can be managed within the app.
& “Using LIBRARIAN”

Contents
Using FAVORITE
Using FAVORITE
Using the FAVORITE Screen
MEMO
Buttons that are marked with the“ ” symbol can be pressed and held to
display other windows or to switch to a dierent screen (this works the same
with the EDITOR).
The currently selected scene is
shown.
* The language used to display the
scene names changes according to
the Aerophone’s language settings.
The scenes registered as favorites
are shown.
Tap to switch scenes.
Hold down the FAVORITE button
to register the current scene as a
favorite.
Tap the icon to show all
scenes (preset/user) in the
Aerophone.
You can switch to a dierent
scene as desired.

Contents
Using EDITOR
Setting the Parameter Values
Operate the app as shown below to set a parameter’s value.
* You can scroll the parameter list up/down.
Setting a value
When you tap a value, a controller appears.
Tap a value and hold the controller down to display the numeric
keypad or list.
Operation Explanation
Swipe left/right Changes the value
Tap +/- Set the detailed value
Setting a range
Operation Explanation
Swipe the left side Sets the lowest value
Swipe the right side Sets the highest value

Contents
Using EDITOR
Turning all eects o
1.
Tap“Scene Eects”in SCENE VIEW and turn all the eects o.
2.
Tap the MFX for each part in SCENE VIEW to turn them all o.
3.
Press the [WRITE] button in SCENE VIEW to save the scene.
Now all of the eects should be turned o.

Contents
Using EDITOR
Using the EDITOR Screen
SCENE VIEW
[WRITE] button
Saves the scene you
are now editing as an
Aerophone user scene.
Tap this to switch
between scenes to edit.
Scene Eects
Displays the scene eect
setting status. Tap each
eect to turn it on/o.
* Hold down the eect name to
go to the eect edit screen.
[COMMON] button
Switches to the edit
screen for common scene
parameters.
& “AE-30/AE-20
Parameter Guide”
(PDF)
Control/Assign
Switches to the settings
screen for control/assign
parameters.
INTERNAL Internal sound
engine
MIDI OUT External
sound engine
& “AE-30/AE-20
Parameter Guide”
(PDF)
Part
Displays the settings for
each part. Tap the number
to turn a part on/o.
* Hold down to go to the part
edit (PART VIEW) screen.
Tone Tones selected
in parts
Switches tones
MFX
(solid line)
Part
MFX
(dotted line)
Tone
MFX
Tap each eect
to turn it on/o.
* Hold down the
eect name to
go to the eect
edit screen.
Out Asgn
(Output
Assign)
Output
destination
for part (either
IFX or DRY
routed to Scene
Eects).
The currently selected
scene is shown.
* Hold this down to display
the scene name edit
window.
* The language
used to display
the scene names
changes according
to the Aerophone’s
language settings.

Contents
Using EDITOR
PART VIEW
Hold down parts 1–4 in SCENE VIEW to display the edit screen (PART
VIEW) for the part you pressed.
Tap to return to the
previous screen.
[COPY] button
Switches to the PART
COPY screen.
Use this to copy
parameters between
parts.
[WRITE] button
Saves the scene you
are now editing as an
Aerophone user scene.
PART tab
Tap to select the part to
edit.
Parts for which the
“PartSW” (part switch)
control is on are
highlighted.
Part Sw
Turns parts on/o that
you are editing.
[EDIT] button
Switches to the edit
screen for tones (TONE
VIEW).
* Only ZEN-Core tones can be
edited.
Parameter List
Shows the parameters in
the group.
& “AE-30/AE-20
Parameter Guide”
(PDF)
Parameter group
Switches between
parameter groups, such
as MODE and RANGE.
Tone
Displays tones selected
in parts. Tap to switch
between tones.