Roland RS-5 Operating and maintenance manual

RS-5 Jan. 2001
1
TABLE OF CONTENTS Page
SPECIFICATIONS ................................................................................................................................................................. 1
PANEL LAYOUT .................................................................................................................................................................... 2
EXPLODED VIEW ................................................................................................................................................................. 3
PARTS LIST........................................................................................................................................................................... 4
IDENTIFYING THE VERSION NUMBER .............................................................................................................................. 7
Saving and loading user data ................................................................................................................................................ 7
Factory Reset procedure ....................................................................................................................................................... 9
Upgrading the program memory software version ................................................................................................................. 9
TEST MODE .......................................................................................................................................................................... 11
ERROR MESSAGE ............................................................................................................................................................... 15
KEYBOARD DISASSEMBLY................................................................................................................................................. 16
CIRCUIT BOARD(KEYBOARD) ............................................................................................................................................ 16
KEYBOARD CIRCUIT DIAGRAM.......................................................................................................................................... 17
KEYBOARD DISASSEMBLY................................................................................................................................................. 17
BLOCK DIAGRAM ................................................................................................................................................................. 19
CIRCUIT BOARD (MAIN BOARD)......................................................................................................................................... 20
CIRCUIT DIAGRAM (MAIN BOARD 1/4)............................................................................................................................... 21
CIRCUIT DIAGRAM (MAIN BOARD 2/4)............................................................................................................................... 22
CIRCUIT DIAGRAM (MAIN BOARD 3/4)............................................................................................................................... 23
CIRCUIT DIAGRAM (MAIN BOARD 4/4)............................................................................................................................... 24
CIRCUIT BOARD(PANEL A/B BOARD) ................................................................................................................................ 25
CIRCUIT DIAGRAM (PANEL A BOARD) .............................................................................................................................. 26
CIRCUIT DIAGRAM (PANEL B BOARD) .............................................................................................................................. 27
SERVICE NOTES
First Edition
Issued by RJA
Copyright © 2001 by ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
17059088 Printed in Japan (A000) (CM)
SPECIFICATIONS
64-voice synthesizer (Conforms to General MIDI 2 System)
●Keyboard
61 keys (with velocity)
●Parts
16
●Maximum Polyphony
64 voices
●Wave Memory
32 M bytes (16-bit linear equivalent)
●Preset Memory
Tones: 512 (RS-5 Original: 256, General MIDI 2: 256)
Performances: 128
Drum Sets: (RS-5 Original: 11, General MIDI 2: 9)
●User Memory
Tones: 128
Performances: 128
Drum Sets: 2
●Effects
Multi-Effects: 42 types
Reverb: 8 types
Chorus: 8 types
●Arpeggiator
45 styles
●Controllers
Pitch Bend/Modulation Lever
Control Knobs: 6
●Display
20 characters, 2 lines (Backlit LCD)
7 segments, 3 charavters (LED)
●Connectors
Output Jacks (L (MONO), R)
Headphones Jack
MIDI Connectors (IN, OUT, THRU)
Hold Pedal Jack
Control Pedal Jack
●Power Supply
DC 9V (AC Adaptor)
●Current Draw
600 mA
●Dimensions
1033 (W) ×294 (D) ×103 (H) mm
40-11/16 (W) ×11-5/8 (D) ×4-1/16 (H) inches
●Weight
6.0 kg / 13 lbs 4 oz (excluding AC adaptor)
●Accessories
Owner's Manual {Japanese (#71784356), English (#71787534)}
AC Adaptor (ACI/ACB Series)
ACB-230E (#01458278)
ACB-240(A) (#12449549)
ACI-100C (#00905756)
ACI-120C (#00905767)
ACI-230C (#01018312)
●Options
Pedal Switch: DP-2/6
Foot Switch: BOSS FS-5U
Expression Pedal: EV-5
* In the interest of product improvement, the specifications and/or appearance of
this unit are subject to change without prior notice.

RS-5 Jan. 2001
2
TOP PANEL
REAR PANEL
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
PANEL LAYOUT Top Panel parts list
NO. PART CODE PART NAME DESCRIPTION Q'TY
q02453289 TOP PANEL S BLK/LCG 1
w02452912 J R-KNOB SF-A BLK/LCG 1
02455234 12M/M ROTARY POT. EVJY15F02B14 1
e02452912 J R-KNOB SF-A BLK/LCG 6
02455223 9M/M ROTARY POT. EVUF2KFK4B14 6
r02453312 DISPLAY COVER 1
t01342534 LED SL-9351S 1
y02453345 LCD HOLDER 1
02453145 LCD RCM2072M-A 1
02453156 LED LNJ801TP6JA 8
u01783923 N S-KEYTOP MX1H 8
i01783978 N S-KEYTOP MX2H 2
o01783990 N S-KEYTOP MX4H 2
!0 01783923 N S-KEYTOP MD1H 6
!1 01783934 N S-KEYTOP MD2H 2
!2 01783956 N S-KEYTOP MD4H 2
u~!2 01340290 TACT SWITCH EVQ11A H=5.0 38
!0~!2 01787045 LED (ORANGE) SLR-325DCT31 18
Rear Panel parts list
NO. PART CODE PART NAME DESCRIPTION Q'TY
q02453289 TOP PANEL 1
w00896934 BOTTOM CASE 1
e13429273 MIDI CONNECTOR YKF51-5046 (TRIPRET) 1
r00569278 6.5MM JACK LGR4609-7100 5
t22365714 CORD HOOK 1
y13449720 DC JACK HEC2305-01-250 1
u12499175 G S-BUTTON S1H BLK 1
01676512 PUSH SWITCH SDKLA1-B 1
[SCREW]
A40011312 SCREW 3X8 BINDING TAPTITE P BZC 2
B40011490 SCREW M3X6 PAN MACHINE W/SW 3
C40011101 SCREW 3X8 BINDING TAPTITE B 1
12
345 67
9
10 11
12
10
7
7107837 10
10
31 45
2A B
C6
7



RS-5 Jan. 2001
3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
EXPLODED VIEW
[PART]
NO. PART CODE PART NAME DESCRIPTION Q'TY
q00896934 BOTTOM CASE 1
w00340690 FOOT ZULEN (CUSHION) XCK040 12MM 4
e02455956 PANEL HOLDER 2
r71784401 PWB PANEL A ASSY 1
t71784412 PWB PANEL B ASSY 1
y02453312 DISPLAY COVER 1
u22365714 CORD HOOK 236-714 1
i12499175 G S-BUTTON S1H BLK 249-175 1
o70564101 BENDER TURBOLESS PB-H0201 1
!0 02453289 TOP PANEL 1
!1 02453290 SIDE PANEL L 1
!2 02453301 SIDE PANEL R 1
!3 02452912 J R-KNOB SF-A BLK/LCG 7
!4 02453323 SIDE HOLDER L 1
!5 02453334 SIDE HOLDER R 1
!6 02456234 SHIELD SHEET 1
!7 40016589 NYLON RIVET NRP-335 1
!8 71784423 MAIN BOARD ASSY (EXG) 1
!9 23505278 WIRING HARNESS J-1 350-278 2
@0 70676189 KEYBOARD ASSY SK-961-B 1
[SCREW]
NO. PART CODE PART NAME DESCRIPTION
A40011123 SCREW 4X8 BINDING TAPTITE B BZC 20
B40011056 SCREW 3X6 BINDING TAPTITE B ZC 19
C40011067 SCREW 3X8 BINDING TAPTITE B FE ZC 12
D40011312 SCREW 3X8 BINDING TAPTITE P BZC 12
E40011490 SCREW M3X6 PAN MACHINE W/SW BZC 3
F40011101 SCREW 3X8 BINDING TAPTITE B BZC 1
G40011034 SCREW 3X8 PAN TAPTITE B W/PW ZC 3


RS-5 Jan . 2001
4
*1 *2
↓↓ CASING Q'ty
00896934 BOTTOM CASE 1
NOTE : 'BOTTOM CASE' includes the following parts.
00340690 FOOT ZULEN (CUSHION) 4
# 02453312 DISPLAY COVER 1
# 02453290 SIDE PANEL L 1
# 02453301 SIDE PANEL R 1
# 02453289 TOP PANEL 1
CHASSIS
# 02455956 PANEL HOLDER 2
# 02453334 SIDE HOLDER R 1
# 02453323 SIDE HOLDER L 1
KNOB, BUTTON
12499175 G S-BUTTON S1H BLK 249-175 1
# 02452912 SF-A BLK/LCG J R-KNOB 7
SWITCH
01340290 EVQ11A H=5.0 TACT SWITCH SW6,SW1,SW2,SW3,SW5,
SW7,SW8,SW9,SW10,SW11,
SW4 on PANEL A BOARD,
SW22,SW38,SW12,SW13,SW14,
SW15,SW16,SW17,SW18,SW19,
SW21,SW23,SW24,SW32,SW37,
SW36,SW35,SW20,SW33,SW25,
SW31,SW30,SW29,SW28,SW27,
SW26,SW34 on PANEL B
BOARD 27 +11
01676512 SDKLA1-B PUSH SWITCH SW2 on MAIN BOARD 1
JACK, SOCKET
13429273 YKF51-5046 (TRIPRET) MIDI CONNECTOR JK1 on MAIN BOARD 1
00569278 LGR4609-7100 6.5MM JACK JK2,JK4,JK5,JK6,JK3 5
on MAIN BOARD
13449720 HEC2305-01-250 DC JACK JK7 on MAIN BOARD 1
DISPLAY UNIT
# 02453145 RCM2072M-A LCD IC4 on PANEL A BOARD 1
NOTE : Replacement RCM2072M-A should be made on a unit base.
01342534 SL-9351S LED 7 SEGMENT LED7 on PANEL A BOARD 1
PARTS LIST BENDER UNIT
70564101 PB-H0201 BENDER TURBOLESS 1
NOTE : Replacement PB-H0201 should be made on a unit base.
KEYBOARD ASSY
70676189 KEYBOARD ASSY SK-961-B 1
NOTE : See 'KEYBOARD PARTS LIST' for details.
PCB ASSY
# 71784412 PWB PANEL B ASSY 1
NOTE : 'PWB PANEL B ASSY' includes the following parts.
01783967 N S-KEYTOP MX1H 7
01783923 N S-KEYTOP MD1H 4
01783934 N S-KEYTOP MD2H 2
01783978 N S-KEYTOP MX2H 2
01783990 N S-KEYTOP MX4H 2
# 71784401 PWB PANEL A ASSY 1
NOTE : 'PWB PANEL A ASSY' includes the following parts.
# 02560123 JWFV 10X175-P2.0 RIBBON CABLE 1
# 02453345 LCD HOLDER 1
01783923 N S-KEYTOP MD1H 2
01783956 N S-KEYTOP MD4H 2
01783967 N S-KEYTOP MX1H 1
# 71784423 MAIN BOARD ASSY (EXG) 1
NOTE : 'MAIN BOARD ASSY' includes the following parts.
22465224 HEATSINK 246-224 1
12199584
GROUNDING TERMINAL M1698 M3,M4,M2 on MAIN BOARD 3
40013067 SCREW M3X8 PAN MACHINE W/SW+SMALL PW ZC 1
IC
15169605 TC74HC4052AP IC (CMOS) IC2 on PANEL A BOARD 1
15189134 NJM2904D IC (OP AMP) IC1 on PANEL A BOARD 1
15189189 UPC4570HA IC (BIPOLAR OP AMP) IC3 on PANEL A BOARD 1
# 02456478 HD6437016E17F VER1.00 IC (CPU 32BIT) IC2 on MAIN BOARD 1
01679978 RA09-002XP6TC203C180AF002 IC (CUSTOM) IC14 on MAIN BOARD 1
00129278 SSC1080F0B IC IC27 on MAIN BOARD 1
01342978 TC160G22AF-1253 IC (CUSTOM) IC3 on MAIN BOARD 1
01670701 DRAM MSM514260C-50JS-7DR1 IC (DRAM) IC23,IC4 on MAIN BOARD 2
01900678 BR93LC46FV-WE2 IC (EEPROM) IC36 on MAIN BOARD 1
# 02452489 UPD23C128040LGY-508-MJH IC (MASK ROM) IC15 on MAIN BOARD 1
02010601 MBM29F800BA-70 IC (FLASH MEMORY) IC34,IC35 on MAIN BOARD 2
01451578 AK4324-VF-E2 IC (DAC) IC22 on MAIN BOARD 1
15269219H0 HD74LS05FPEL IC (TTL) IC1 on MAIN BOARD 1
15249111 TC7WU04F(TE12L) IC (CMOS) IC20 on MAIN BOARD 1
15259885 TC7S32F(TE85L) IC (CMOS) IC17 on MAIN BOARD 1
15259738T0 TC74HC138AF(EL) IC (CMOS) IC26 on MAIN BOARD 1
15259769T0 TC74HC238AF(EL) IC (CMOS) IC29 on MAIN BOARD 1
15259884 TC7S08F(TE85L) IC (CMOS) IC24 on MAIN BOARD 1
15259823T0 TC74HC574AF(EL) IC (CMOS) IC28 on MAIN BOARD 1
15289109 M5216FP-600D IC (BIPOLAR OP AMP) IC18 on MAIN BOARD 1
15289141 M5223FP-600D IC (BIPOLAR OP AMP) IC25 on MAIN BOARD 1
15289105 UPC4570G2-E2 IC (BIPOLAR OP AMP) IC21 on MAIN BOARD 1
15199137 AN7805F IC (V.RGL) IC33 on MAIN BOARD 1
01458445 UPC29M33T-T1 IC (REGULATOR) IC32 on MAIN BOARD 1
15199286 AN78L05M-(E1) IC (REGULATOR) IC30 on MAIN BOARD 1
15199937 M51953BFP-600C IC (RESET) IC10 on MAIN BOARD 1
15289125 PC-410KT 178FAY IC (PHOTO COUPLER) IC6 on MAIN BOARD 1
CONSIDERATIONS ON PARTS ORDERING
When ordering any parts listed in the parts list, please specify the following items in the order sheet.
QTY PART NUMBER DESCRIPTION MODEL NUMBER
10 22575241 Sharp key C-20/50
15 2247017300 Knob (orange) DAC-15D
Failure to completely fill the above items with correct number and description will result in delayed or even
undelivered replacement.
Ex.
SAFETY PRECAUTION:*1
The parts marked have safety-
related characteristics.
Use only listed parts for
replacement.
The parts marked #
are new (initial
parts). *2

RS-5 Jan. 2001
5
TRANSISTOR
01121278 2SA1576A T106 QRS TRANSISTOR Q6 on MAIN BOARD 1
15309101 2SA1037AKT146R TRANSISTOR Q24,Q25 on MAIN BOARD 2
15319101 2SC2412KR T146 TRANSISTOR Q7,Q30 on MAIN BOARD 2
15319105 2SC3326-A TRANSISTOR Q27,Q28,Q5,Q4 on MAIN BOARD 4
00562012 2SC3265-Y(TE85R) TRANSISTOR Q26 on MAIN BOARD 1
01907267 DTA124EUA T-106 TRANSISTOR Q1 on MAIN BOARD 1
01783612 RN2426(TE85L) TRANSISTOR Q15,Q9,Q11,Q12,Q13,Q14
on MAIN BOARD 6
01451245 RN1414(TE85L) TRANSISTOR Q20,Q21,Q23,Q16,Q22,Q19,Q17,
Q18 on MAIN BOARD 8
15329521 RN1307(TE85R) TRANSISTOR Q8 on MAIN BOARD 1
DIODE
15019126 1SS133 T-77 SWITCHING DIODE D10,D1,D2,D3,D4,D5,D6,D7,D9,
D11,D8 on PANEL A BOARD,
D16,D23,D22,D21,D20,D19,D17,
D27,D15,D14,D13,D12,D18,D24,
D26,D28,D29,D30,D31,D32,D33,
D34,D35,D36,D37,D38,D25
on PANEL B BOARD 27 +11
01787045 SLR-325DCT31 LED (ORANGE) LED8,LED15,LED16,LED17,
LED14,LED11,LED10,LED9,
LED4,LED5 on PANEL A
BOARD,LED23,LED22,LED18,
LED19,LED21,LED25,LED24,
LED20 on PANEL B BOARD 8 +10
# 02453156 LNJ801TP6JA LED LED30,LED34,LED29,LED31,
LED32,LED33,LED27,LED28
on PANEL A BOARD 8
02014778 U1GC44(TE12L) RECTIFIER DIODE D3 on MAIN BOARD 1
01897189 MA147-(TX) ARRAY DIODE DA16,DA1,DA2,DA4,DA13,DA12,
DA15,DA3 on MAIN BOARD 8
15339130 MA142WK-(TX) ARRAY DIODE DA10,DA11,DA7,DA6,DA5,DA9
on MAIN BOARD 6
RESISTOR
13749767T0 SR25TRE 560J CARBON RESISTOR R12,R13,R11,R14 on PANEL A
BOARD,R36,R37,R38
on PANEL B BOARD 3 +4
13749793T0
SR25TRE 681 J 680 OHM 1/4W CARBON RESISTOR R56,R58,R57,R55 on PANEL A
BOARD 4
13749773T0 SR25TRE 101 J CARBON RESISTOR R22,R16,R20,R17,R18,R19,R21,
R15 on PANEL A BOARD 8
13749831T0 SR25TR 273 J CARBON RESISTOR 2
13749775T0 SR25TRE 121 J CARBON RESISTOR R8,R6,R7,R5,R1,R2,R3,R4
on PANEL A BOARD 8
13749815T0 SR25TRE 562 J CARBON RESISTOR R34,R35 on PANEL A BOARD 2
13749819T0 SR25TRE 822 J 1/6W CARBON RESISTOR R30,R29,R26,R25
on PANEL A BOARD 4
# 15399581 RPC18T 221 J CARBON RESISTOR R113 on MAIN BOARD 1
13749821T0 SR25TRE 103 J CARBON RESISTOR 1 (1.00~21.99lotのみ)
00567023 RPC05T 101 J MTL.FILM RESISTOR R115,R128,R95,R80,R77,R74,R71,
R6,R170,R171 on MAIN BOARD 8
00567289 RPC05T 103 J MTL.FILM RESISTOR R16,R37,R36,R32,R31,R18,R150,
R12,R4,R42,R29,R96,R139,R101,
R169,R54,R167,R89,R83,R79,R68,
R67,R66,R60,R55,R168 on MAIN
BOARD 25 (22.00lotから26)
00567078 RPC05T 271 J MTL.FILM RESISTOR R30,R97,R65 on MAIN BOARD 3
00567156 RPC05T 102 J MTL.FILM RESISTOR R87,R75,R129,R2,R120,R147,R131,
R155,R157,R121,R159,R130,R149,
R161,R40 on MAIN BOARD 15
00567212 RPC05T 332 J MTL.FILM RESISTOR R132,R22,R88,R140,R76
on MAIN BOARD 5
00567256 RPC05T 562 J MTL.FILM RESISTOR R92,R91,R48,R49,R50,R51,
R81,R82 on MAIN BOARD 8
01011856 RPC05T 0R0 J MTL.FILM RESIST0R R142,R3,R111,R98,R69,R64,R44,
R41,R11,R35,R27,R25,R24,R23,
R38,R144 on MAIN BOARD 16
00567412 RPC05T 104 J MTL.FILM RESISTOR R112 on MAIN BOARD 1
00567067 RPC05T 221 J MTL.FILM RESISTOR R8,R9,R10,R21,R7 on MAIN
BOARD 5
00567089 RPC05T 331 J MTL.FILM RESISTOR R164,R163 on MAIN BOARD 2
00566990 RPC05T 680 J MTL.FILM RESISTOR R39 on MAIN BOARD 1
00567034 RPC05T 121 J MTL.FILM RESISTOR R5 on MAIN BOARD 1
00566967 RPC05T 470 J MTL.FILM RESISTOR R137,R56,R138 on MAIN BOARD 3
00567501 RPC05T 474 J MTL.FILM RESISTOR R136,R135 on MAIN BOARD 2
00567312 RPC05T 183 J MTL.FILM RESISTOR R63,R59 on MAIN BOARD 2
00567278 RPC05T 822 J MTL.FILM RESISTOR R58,R61 on MAIN BOARD 2
00567267 RPC05T 682 J MTL.FILM RESISTOR R94,R84,R90,R93,R78 on MAIN
BOARD 5
00567245 RPC05T 472 J MTL.FILM RESISTOR R20,R47,R118,R126,R33 on
MAIN BOARD 5
# 00566901 RPC05T 180 J MTL.FILM RESISTOR R153,R154 on MAIN BOARD 2
00567123 RPC05T 561 J MTL.FILM RESISTOR R156,R158,R162,R160 on MAIN
BOARD 4
00567112 RPC05T 471 J MTL.FILM RESISTOR R116,R114 on MAIN BOARD 2
00567378 RPC05T 473 J MTL.FILM RESISTOR R1 on MAIN BOARD 1
00567556 RPC05T 105 J MTL.FILM RESISTOR R62 on MAIN BOARD 1
# 02455967 RK73K2HTE330J MTL.FILM RESISTOR R53,R52 on MAIN BOARD 2
# 02455978 RK73K2HTE470J MTL.FILM RESISTOR R148,R146 on MAIN BOARD 2
01906667 MNR14 EOAB J 100 RESISTOR-ARRY RA23,RA30,RA29,RA24,RA28
on MAIN BOARD 5
01906945 MNR14 E0AB J 101 RESISTOR-ARRY RA21,RA22 on MAIN BOARD 2
02231590 MNR14 EOAB J 221 RESISTOR-ARRAY RA27,RA26 on MAIN BOARD 2
01457145 EXBE10C103J RESISTOR ARRAY RA10,RA7,RA25,RA13 on MAIN
BOARD 4
# 02453089 EXBE10C472J RESISTOR ARRAY RA35,RA19,RA20 on MAIN
BOARD 3
01906678 MNR14 EOAB J 103 RESISTOR-ARRY RA12,RA16,RA15,RA14 on MAIN
BOARD 4
POTENTIOMETER
# 02455223 EVUF2KFK4B14 9M/M ROTARY POTENTIOMETER VR4,VR6,VR1,VR3,VR5,VR2
on PANEL A BOARD 6
# 02455234 EVJY15F02B14 12M/M ROTARY POTENTIOMETER VR7 on PANEL A BOARD 1
CAPACITOR
13519401M0 ECFR1E104ZF5 CERAMIC CAPACITOR C21,C2,C1,C3,C20,C12,C9,C4,C5,
C8,C7,C6 on PANEL A BOARD 12
13519634M0 ECKR1H102KB5 CERAMIC CAPACITOR C33 on PANEL A BOARD 1
00239412 AMZV0050J122 0200 POLYEST. CAPACITOR C10,C16 on PANEL A BOARD 2
00239390 AMZV0050J561 0200 POLYEST. CAPACITOR C13,C17 on PANEL A BOARD 2
01900834 RA2-16V101M-T2 CHEMICAL CAPACITOR C19,C18,C15,C11 on PANEL A
BOARD 4
13639546M0 ECEA1CKA100B 10UF/16V CHEMICAL CAPACITOR C14 on PANEL A BOARD 1
01674190 ECUV1H150JCV CERAMIC CAPACITOR C228,C168,C218,C226,C227,C166,
C215,C229,C165,C159,C150,C230,
C231,C167,C177,C169,C170,C149,
C174,C217,C176,C216,C178,C179,
C180,C211,C212,C213,C214,C175,
C109,C148,C87,C88,C95,C103,
C135,C136,C138,C139,C146,C141,
C142,C143,C144,C145,C140,C101,
C147 on MAIN BOARD 49
01674334 ECUV1H101JCV CERAMIC CAPACITOR C74,C75,C96,C104,C153,C160,
C151,C154,C152,C155,C157,C234,
C236,C156,C239,C240,C243
on MAIN BOARD 14
01674389 ECUV1H221JCV CERAMIC CAPACITOR C161 on MAIN BOARD 1

RS-5 Jan . 2001
6
01674612 ECJ1VB1H103K CERAMIC CAPACITOR C129,C127,C126,C124,C184,C125,
C192,C128,C241,C242
on MAIN BOARD 8
01674212 ECUV1H220JCV CERAMIC CAPACITOR C40,C41 on MAIN BOARD 2
02129534 ECJ1VB1H102K CERAMIC CAPACITOR C185,C196 on MAIN BOARD 2
01674356 ECUV1H151JCV CERAMIC CAPACITOR C237,C235 on MAIN BOARD 2
01674701 ECJ1VF1E104Z 0.1UF/16VK CERAMIC CAPACITOR C66,C113,C112,C111,C110,C93,
C117,C86,C121,C80,C73,C72,
C71,C70,C69,C68,C209,C92,C186,
C204,C203,C201,C200,C198,C197,
C193,C115,C187,C65,C182,C171,
C164,C163,C137,C134,C133,C132,
C131,C188,C12,C21,C67,C19,
C18,C17,C16,C15,C82,C13,C22,
C11,C10,C9,C8,C7,C6,C5,C4,C2,
C14,C55,C64,C63,C62,C61,C60,
C59,C58,C20,C56,C23,C44,C39,
C37,C33,C31,C30,C28,C27,C26,
C57,C78 on MAIN BOARD 82
01674712 ECJ1VF1A105Z CERAMIC CAPACITOR C195,C45 on MAIN BOARD 2
01674423 ECUV1H471JCV CERAMIC CAPACITOR C32 on MAIN BOARD 1
01783467 RV2-16V101MZ7-R CHEMICAL CAPACITOR C81,C90,C99,C102,C107,C114,
C120,C85,C207,C208,C205
on MAIN BOARD 11
# 02345067 RV2-25V4R7M-R CHEMICAL CAPACITOR C232,C233 on MAIN BOARD 2
01784478 RV2-6V470MZ7-R CHEMICAL CAPACITOR C1,C51,C199,C210,C3 on MAIN
BOARD 5
13669404 ECA1CM222 2200UF/16V CHEMICAL CAPACITOR C221 on MAIN BOARD 1
01564778 RV2-16V100MZ7-R 10UF/16VCHEMICAL CAPACITOR C106,C206,C94,C98,C91,C116,
C108,C172,C181,C100,C29,C183,
C54 on MAIN BOARD 13
INDUCTOR, COIL, FILTER
00237212 SH-202 CHOKE COIL FL1 on MAIN BOARD 1
01565578 N1608Z601T01 FERRITE-BEAD L12,L14,L15,L11,L17,L7,L21,L16,
L10,L23,L8,L22,L6,L5,L4,L3,L2,
L1,L9,L18,L24 on MAIN BOARD 21
CRYSTAL, RESONATOR
01126267 MA-406 7.056MHZ CRYSTAL X1 on MAIN BOARD 1
00901912 MA-406 24.576MHZ TE24 CRYSTAL X2 on MAIN BOARD 1
CONNECTOR
02010878 18FE-ST-VK-N FOR WIRING CONNECTOR CN4 on PANEL B BOARD 1
02018712 20FE-ST-VK-N FOR WIRING CONNECTOR CN1 on PANEL A BOARD 1
13429299 51048-1000(10P) CABLE HOLDER CN2 on PANEL A BOARD 1
02018689 32FE-ST-VK-N FOR PCB CONNECTOR CN3 on PANEL A BOARD 1
01908656 18FE-BT-VK-N CONNECTOR CN8 on MAIN BOARD 1
02014445 20FE-BT-VK-N CONNECTOR CN9 on MAIN BOARD 1
02019001 32FE-BT-VK-N FOR WIRING CONNECTOR CN7 on MAIN BOARD 1
02010867 16FE-ST-VK-N FOR WIRING CONNECTOR CN3,CN5 on MAIN BOARD 2
13369605 52147-1010(10P) WIRE TRAP CN2 on MAIN BOARD 1
13369940 53254-0410 CONNECTOR CN6 on MAIN BOARD 1
WIRING, CABLE
23505278 WIRING HARNESS J-1 350-278 2
00899456 WIRING W-1 1
# 02456023
BNCD-P=1.25-K-16-260-S W/O GS BAN CARD 2
# 02457656 BNCD-P=1.25-K-18-260-S W/O GS BAN CARD 1
# 02457667
BNCD-P=1.25-K-32-160-S W/O GS BAN CARD 1
# 02457689 BNCD-P=1.25-K-20-200-S W/O GS BAN CARD 1
SCREW
40011034 SCREW 3X8 PAN TAPTITE B ZC 3
40011056 SCREW 3X6 BINDING TAPTITE B ZC 4 +15
40011123 SCREW 4X8 BINDING TAPTITE B BZC 20
40011101 SCREW 3X8 BINDING TAPTITE B BZC 1
40011312 SCREW 3X8 BINDING TAPTITE P BZC 8 +4
40011490 SCREW M3X6 PAN MACHINE W/SW BZC 3
40011067 SCREW 3X8 BINDING TAPTITE B FE ZC 12
PACKING
# 02561534 PAD UPPER CENTER 1
# 02561512 PAD SIDE R 1
# 02561501 PAD SIDE L 1
# 02561523 PAD LOWER CENTER 1
# 02455945 PACKING CASE 1
MISCELLANEOUS
22365714 CORD HOOK 236-714 1
# 02456234 SHIELD SHEET 1
40016589 NYLON RIVET NRP-335 1
ACCESSORIES (STANDARD)
01458278 AC ADAPTOR ACB-230E 1
12449549 AC ADAPTOR ACB-240(A) 1
00905756 AC ADAPTOR ACI-100C 1
00905767 AC ADAPTOR ACI-120C 1
01018312 AC ADAPTOR ACI-230C 1
00905234 ECP01-5A (PLUG FOR BRC-230T) EURO CONVERTER PLUG 1
# 71784356 JAPANESE OWNER'S MANUAL 1
# 71787534 ENGLISH OWNER'S MANUAL 1

RS-5 Jan. 2001
7
IDENTIFYING THE VERSION
NUMBER
1. Checking the version number
Turn on the power while pressing the [PERFORM/TONE],
[USER/PRESET] and [1/PIANO] buttons.
The title screen of the test mode appears and the version of each
CPU and ROM is displayed.
Saving and loading user data
Items required:Sequencer(XP-80,MC-80,etc)
MIDI cable
You can save the user data to an external sequencer (Bulk Dump)
The process of transmitting tone, Drum Set, Performance or System
settings on an external MIDI device is called Bulk Dump.
How to data save
Setting the Device ID Number
When carrying out Bulk Dump, set the Device ID number. When
shipped from the factory, this is set to "17." Normally, there is no
need to change this number when transmitting data to a sequencer or
other such device. If you do want to change it, use the following
procedure to make the settings.
1. Press [EDIT], getting the indicator to light.
2. Use VALUE [-]/[+] to select "System Setup."
3. Press [ENTER].
4. Press the numeric key [4] several times to select "Device ID#."
* If you hold down [SHIFT] and press [4], you will return to the
previous item.
5. Press VALUE [-]/[+] to select value(17 to 32)
6. Press [EDIT].
The [EDIT] indicator goes out, and you are returned to the previous
screen.
Bulk dump procedure
Types of bulk dump
Temporary: Settings of temporary area
User Tone: Settings of all User Tones
User Drum Set: Settings of all User Drum Sets
User Performance:Settings of all User Performances
System Setup: Settings of System Setup

RS-5 Jan. 2001
8
However, the following system setup parameters will not be
transmitted via bulk dump.
Rx SysEx Sw
Device ID#
LCD Contrast
All:All five of the above settings (The SYSEX of Use Tone will
not be output for Version Number of ROM. Please refer to
the Service information No.10134a [Ver.1.03])
1. Use a MIDI cable to connect the RS-5's MIDI OUT connector
to the MIDI IN connector of the external sequencer.
2. Press [UTILITY], getting the indicator to light.
3. Use VALUE [-]/[+] to select "Bulk Dump."
4. Press [ENTER].
5. Use the VALUE [-]/[+] to select the types of Bulk Dump.
6. Put the external sequencer in record mode.
7. Press [ENTER] to transmit the settings.
The message "Transmitting..." appears in the display during
transmission of the data.
* Do not press any key on the keyboard while Bulk Dump is in
progress. Pressing a key sends Note messages from the MIDI
OUT connector. To cancel the Bulk Dump, press [EXIT].
After the transmitting is finished, the display will indicate
"Completed."
The [UTILITY] indicator goes out, and you are returned to the
previous screen.
8.Stop the external sequencer.
How to data load
Setting the System Exclusive Receive Switch
When returning saved settings to the RS-5, set the Exclusive
Receive switch to ON. With the factory settings, this will be "ON."
1. Press [EDIT], getting the indicator to light.
2. Use VALUE [-]/[+] to select "System Setup."
3. Press [ENTER].
4. Press the numeric key [4] several times to select "System
Exclusive."
* If you hold down [SHIFT] and press [4], you will return to the
previous item.
5. Use VALUE [-]/[+] to set "ON."
6. Press [EDIT].
The [EDIT] indicator goes out, and you are returned to the
previous screen.
Restoring saved settings to the RS-5
* Be aware that when you restore data to the RS-5, the data in the
RS-5 will be overwritten and lost.
1. Use a MIDI cable to connect the MIDI OUT connector of the
external sequencer to the MIDI IN connector of the RS-5.
2. Set the device ID number to the same setting as when you
performed the bulk dump.
System Setup Numeric Key [4] : Device ID
(refer to " Setting the Device ID Number")
3. Turn on the exclusive receive switch.
System Setup Numeric Key [4] : System Exclusive
(refer to " Setting the System Exclusive Receive Switch")
4. Transmit (play back) the data from the external sequencer.
When the transmitting is finished, you are returned to the
previous screen.
* Play back the external sequencer at the same tempo you used
when performing the bulk dump. If you use a faster tempo, the
data may not be restored correctly.
Caution:
When data is being written to the User Memory, the message
"KEEP POWER ON!" appears in the display; be sure not to turn off
the power while this message is displayed.
If the power is turned off or interrupted while data is being written
to memory, the internal data may become corrupted, and you may
not be able to turn the power back on. If you have confirmed that,
Upgrade (refer to "Upgrading the program memory software
version") and execute the Factory Reset (refer to "Factory Reset
procedure")

RS-5 Jan. 2001
9
FactoryResetprocedure
You can restore all User Performance, User Tone, User Drum Set
and System Setup settings to the factory condition.
* If the RS-5's internal memory already contains important data
that you have created, this operation will cause all of this data
to be lost. Save data that you want to retain by sending the
data to an external sequencer.
(refer to "Saving and Loading User Data")
Five types of Factory Reset are provided depending on the
application.
User Tone: Settings of all User Tones
User Drum Set: Settings of all User Drum Sets
User Performance:Settings of all User Performances
System Setup: Settings of System Setup
All: All four of the above settings
1. Press [UTILITY], getting the indicator to light.
2. Use VALUE [-]/[+] to select "Factory Reset."
3. Press [ENTER].
4. Use the VALUE [-]/[+] to select the types of Factory Reset.
5. Press [ENTER].
A confirmation message appears.
6. Press [ENTER] to execute the Factory Reset operation.
After the Factory Reset operation is finished, the display will
indicate "Completed."
The [UTILITY] indicator goes out, and you are returned to
the previous screen.
Upgrading the program
memory software version
Upgrading Flash ROM
The RS-5 uses a flash memory for the program ROM.
It can be upgraded by externally inputting MIDI data.
Also, factory resetting must be done after each upgrade.
If important data are written in the user memory, update after
saving it.(See Saving and Loading User Data)
Equipment needed
• RS-5 Ver.Up Disk(17041032)
• The SMF’s playbackable sequencer (machines that can be
played in chain such as the MC-80 and xp-80, 60, 50 are
desirable)
• MIDI cable
Upgrading
1. Connect the MIDI cable to the RS-5 MIDI IN from the MIDI
OUT of the external sequencer.
Setup the SMF to play back in chain if the sequencer can do
so.
2. Simultaneously pressing the [-] and [DUAL] buttons and
turning the power on will bring up the following MIDI update
screen.
3. Pressing [+] will display the following and wait for MIDI
data receiving.
Screen display is [INC] but press [+].
4. After checking 3.’s display, playback all of the “.mid” files
on the RS-5 Ver. UP Disk from the external sequencer.
(Playback in this order p00001.mid--p00016.mid)
While receiving the MIDI data, the [DUAL] LED will flash
and the [Waiting] display will switch to [Receiving].Ending
data transfer of one file will switch the display to [Waiting],
so carry on and play back the next file.

RS-5 Jan. 2001
10
Upgrading is much easier when using a sequencer with a chain
playback function such as the MC-80.Loading and playing the
“.svc” files (chain files) on the disk will automatically playback
all of the “mid.’ files on the disk as well.
Usethefollowingfile.
XP-80,60,50:MITK5XP.SVC
MC-80:MITK5MC.SVC
5. When upgrading is finished correctly, check sum will be
displayed and the FAVORITE PERFORM BANK [1]-[8]
LEDs will flash.
Check that each of the 3 upper case values and the two lower and
central case values match.
(Ignore the right most lower case value.) If they do not match,
upgrading has failed.
Perform upgrading from the beginning again.
6. If a checksum is confirmed, reboot and perform factory
resetting.
(See Factory Resetting)
7. Check the version of the updated Flash ROM.(See Checking
the Version Number)
Cautions:
Number of SMFs
• SMF is made for each Flash Memory block.
• Sixteen SMFs from p00001.mid to p00016.mid are made.
• A file in the middle may be taken out depending on the
program size.
• Since checksum data are placed in p00016.mid, this file will
always be made.
Ending the Update
• After the p00016.mid file has been received, all updated data
are received.
• Erase the block which was not updated at this point.
• This is for correctly managing the checksum data of the
Flash ROM.
• Therefore, updating of only one part of the block cannot be
done.
• If turning off the power while date is being written in Flash
ROM. Preform upgrading from the beginning again.

RS-5 Jan. 2001
11
TEST MODE
Equipment needed
•Headphones
•Monitor speakers (MA-12 etc.), 2
•Audio cables, 2
•MIDI cable, 1
•Expression pedal
•Hold pedal
Cautions on starting the test
•User data may be erased when entering the test mode.
Be sure to back up the data.(See Save and Load of User Data)
•Some of the test items output check sounds.
Connect headphones or monitor speakers beforehand.
Testing items
The RS-5 includes the following tests.
For details on each tests, refer to each item.
0 : Test Mode Title
1 : Memory Test
2 : MIDI Test
3 : Switch & LED Test
4 : LCD & 7-seg LED Test
5 : A/D Test 1 (Bender, Modulation)
6 : A/D Test 2 (Control Knob)
7 : A/D Test 3 (Hold Pedal, Expression Pedal)
8 : Keyboard Test
9 : Sound Test
10 : Factory Reset/User Memory Test
Button operation
Entering the test mode
Turning on the power while pressing the [PERFORM/TONE],
[USER/PRESET] and [1/PIANO] buttons brings up the title
screen of the test mode.
Movement of Each Testing Item
•Pressing [ENTER] on the title screen of the test mode starts the
test mode.
•Testing items 1~3, 5~7 when no problems occur, will
automatically proceed to the next test item.
•Even when the test is not finished, pressing [PART<] or
[PART>] while pressing [SHIFT] proceeds to the next or the
previous testing item, respectively.
Jumping to Each Test
Pressing the ten key while pressing [SHIFT] enables direct
selection of the corresponding testing item.
0 : [SHIFT]+[EXIT] Test Mode Title
1 : [SHIFT]+[1] Memory Test
2 : [SHIFT]+[2] MIDI Test
3 : [SHIFT]+[3] Switch & LED Test
4 : [SHIFT]+[4] LCD & 7seg Test
5 : [SHIFT]+[5] A/D Test1 (Bender & Modulation)
6 : [SHIFT]+[6] A/D Test2 (Control Knob)
7 : [SHIFT]+[7] A/D Test3 ( Hold Pedal, Expression Pedal )
8 : [SHIFT]+[8] Keyboard Test
9 : [SHIFT]+[9] Sound Test
10 : [SHIFT]+[0] Factory Reset/User Memory Test
Ending the test mode
Turn off the power.
* Do not turn off the power while factory resetting.
Turn off the power after terminating factory resetting.
Details on Testing Items
0 : Test Mode Title
•Check the CPU and Program ROM version.
Upgrade when the version is insufficient.
Refer to [Upgrading] for updating.
•Check that the LCD backlight lights evenly.
Check the following parts if it does not .
MAIN BOARD L24,CN9
PANEL A BOARD R55~58, LED27~34, CN1
•Pressing [ENTER] starts the test mode.

RS-5 Jan. 2001
12
1 : Memory Test
•Check the CPU and FLASH ROM (PROGRAM MEMORY).
•OK will be displayed if no problems occur and automatically
proceeds to the next test.
•Check the following parts if NG is displayed.
CPU NG : MAIN BOARD IC2,X1,R11
ROM NG : MAIN BOARD IC35
Pressing [ENTER] proceeds to the next test.
•Check the DRAM and EEPROM.
•OK will be displayed if no problems occur and automatically
proceeds to the next test.
•Check the following parts if NG is displayed.
DRAM NG : MAIN BOARD IC4
EEPROM NG : MAIN BOARD IC36,R41,R44
Pressing [ENTER] proceeds to the next test.
•Check the WAVE ROM and DSP.
•OK will be displayed if no problems occur and automatically
proceeds to the next test.
•Check the following parts if NG is displayed.
WAVE NG : MAIN BOARD IC15
DSP NG-INT : MAIN BOARD IC14,X2
DSP NG-EXT : MAIN BOARD IC23
Pressing [ENTER] proceeds to the next test.
2 : MIDI Test
•Connect MIDI IN and MIDI OUT with MIDI cable.
•OK will be displayed for proper function.
•Then, remove the MIDI cable from MIDI IN and MIDI OUT.
•OK will be displayed for proper function and automatically
proceed to the next test.
•Check the following parts if NG is displayed.
MAIN BOARD JK1, IC1, IC6, L3~8, R5~10, R12, R16, R20,
Q1
Pressing [ENTER] proceeds to the next test.
3 : Switch & LED Test
•All the LEDs will light up when entering this test.
•Pressing the switch will display the switch name on the screen.
•Pressing a switch with LED lit will turn the LED off after
flashing for one second.
•At the upper right of the screen, the number of switches are not
yet pressed are displayed.
•[MANUAL] - [CONTROL] - [LFO ON/OFF] - (FAVORITE
PERFORM BANK)[1] - [2] - [3] - [4] - [5] - [6] - [7] - [8] -
[PHRASE PREVIEW] - [UTILITY] - [SPLIT] - [DUAL] -
[TONE CATEGORY] - [PART <] - [PART >] - [ARPEGGIO
ON/OFF] - [EFFECT ON/OFF] - [PERFORM/TONE] -
[VALUE -] - [VALUE +] - [SHIFT] - [TRANSPOSE ON/
OFF] - [USER/PRESET] - (TENKEY)[1] - [2] - [3] - [4] - [5] -
[EDIT/EXIT] - (TENKEY)[6] - [7] - [8] - [9] - [0] - [ENTER]
Pressing the switches in this order generate a scale from low to
high.
•Check with headphones or speakers.
•Automatically proceeds to the next testing item when all
switches are pressed and functioning properly.
* However, pressing multiple switches simultaneously
cancels them out.
•Check the following parts when the LEDs fail to light up or go
out and the screen display is incorrect.
MAIN BOARD IC3, IC26, IC28, IC29, RA21~22, RA26~27,
Q13~23, CN7, CN8
PANEL A BOARD each LED, SW, DA, R36~38, CN4
PANEL B BOARD each LED, SW, DA, R11~14, CN3
Pressing [SHIFT] + [ENTER] proceeds to the next test.
4 : LCD & 7-segment LED Test
•When entering the test, all the LCD segments go out and the
contrast is maximum.
•When pressing the VALUE [+], all the LCD segments will
light up and the contrast will become dense from the minimum
value in order.
•If you keep on pressing VALUE [-], LCD contrast will become
light.
•When the contrast is 1 to 8, FAVORITE PERFORM BANK 1
to 8 will light up, and the 7-segment LED display will change
from "1.1.1.’to "8.8.8.’

RS-5 Jan. 2001
13
[VALUE] [Contrast value] [7-segment display] [LCD]
-----------------------------------------------------------------------------
Contrast(Max) [ ] All segments go out
−Contrast(1) [1.1.1.] All segments light up
↑Contrast(2) [2.2.2.] ↓
Contrast(3) [3.3.3.] ↓
Contrast(4) [4.4.4.] ↓
↓Contrast(5) [5.5.5.] ↓
＋Contrast(6) [6.6.6.] ↓
Contrast(7) [7.7.7.] ↓
Contrast(8) [8.8.8.] ↓
-----------------------------------------------------------------------------
•Check the LCD contrast and 7-segment LED display.
•Pressing [ENTER] proceeds to the next test.
•Check the following parts when the LCD contrast doesn’t
change or the 7-segment LED display is incorrect.
LCD NG: MAIN BOARD IC3, Q30, L17, C195,
R128, R130, R132, R139, CN9
PANEL A BOARD IC4(LCD),CN1
7-segment LED NG : MAIN BOARD IC3, IC26, IC28, Q9,
Q11, Q12, Q16~23, CN7
PANEL A BOARD LED7(7seg),CN3
5 : A/D Test 1
•Check the bender and modulation functions.
•When entering this test, check to see if the bender is upright.
(To read the A/D value as the mid-point value when entering
this test)
•Pull the bender lever fully to the left and right.
If the reading is –256 when pulling to the left and 256 when
pulling to the right, OK will be displayed.
A check sound will be output when the correct value is
achieved.
•Push the bender lever all the way to the modulation side and
then pull it back.
OK will be displayed if a value of 127 is achieved.
A check sound will be output when the correct value is
achieved.
•Displaying OK for both will automatically proceed to the next
test.
•Check the following parts if OK is not displayed.
Bender unit, bender connector and wiring,
MAIN BOARD Q24~25, L18, L21~23, R118, R120~121,
R126, R129, R131, CN6
Pressing [ENTER] proceeds to the next test.
6 : A/D Test 2
•Check control knob function.
R : RATE
D : DEPTH
A : ATTACK
R : RELEASE
C : CUTOFF
R : RESONANCE
•Move the knob at the way to and from the left and right in this
order: RATE, DEPTH, ATTACK, RELEASE, CUTOFF,
RESONANCE.
•OK will be displayed for each when 0 for fully left, 127 for
fully right and then 0 for fully left again is achieved.
•OK will not be displayed when the order of the knob is
different.
•Also, sweep sound is output while operating the knob and
check sound when the correct value is achieved.
•Displaying OK for all will automatically proceed to the next
test.
•Check the following parts if OK is not displayed.
MAIN BOARD IC2, R167~168, R137~138, CN7
PANEL A BOARD VR1~6, IC1, IC2, CN3
Pressing [ENTER] proceeds to the next test.
7 : A/D Test 3
•Check the functions of the hold and expression pedals.
•Connect the hold pedal to the rear of the PEDAL HOLD.
Step on the hold pedal and restore.
OK will be displayed and a check sound output if the function
is correct.
•Connect the expression pedal to the rear of the PEDAL
CONTROL.
Step on the expression pedal and restore.
Check to see if change occurs between 0-127.
OK will be displayed and a check sound output when the
maximum value is 127 and the minimum value is 0.
Displaying OK for both will automatically proceed to the next
item.
•Check the following parts if OK is not displayed.
HOLD NG : MAIN BOARD JK2, L1~2, R1~2, IC2
EXP NG : MAIN BOARD JK6, IC25, L14~16, R112~116,
IC2
Pressing [ENTER] proceeds to the next test.

RS-5 Jan. 2001
14
8 : Keyboard Test
•Hit all the keys and check that they all generate sound.
Also check that the volume changes depending on how hard
you hit them.
•Pressing [ENTER] changes the tone from PIANO to ORGAN.
Hit all the keys and check that they all generate sound.
•Pressing [ENTER] restores the tone to PIANO.
Repressing [ENTER] proceeds to the next test.
•Check the following when the sound is incorrect.
The keyboard and its connector
MAIN BOARD CN3, CN5, IC27, RA19~20, RA35
9 : Sound Test 1
Check OUTPUT and headphones.
Connect a monitor speaker and headphones and then test.
•A F4 sawtooth wave (about 349Hz) is output from OUTPUT L
and the left headphone.
Check the speakers and headphones for tone.
Check if no sounds are output from OUTPUT R.
* Connect an audio cable to both OUTPUT L and R.
•Pressing [ENTER] proceeds to the next test.
•A F5 sawtooth (about 698Hz) is output from OUTPUT R and
the right headphone.
Check the speakers and headphones for tone.
Check if no sounds are output from OUTPUT L.
* Connect an audio cable to both OUTPUT L and R.
•Pressing [ENTER] proceeds to the next test.
•A F4 sawtooth wave is output from OUTPUT L and the left
headphone and F5 sawtooth wave from OUTPUT R and the
right headphone.
Check if sounds are output from both sides.
•Then remove the audio cable from OUTPUT R and check if
two sawtooth waves, F4 and F5, are output from OUTPUT
L.(Check L MONO)
•Pressing [ENTER] proceeds to the next test.
•When the sound is not output properly, check the following
places.
No sound is output : MAIN BOARD IC22, IC24, Q6~8,
R71, R74, R77, R80, R94~98,
R153~154, CN2
PANEL A BOARD IC3,VR7,CN2
OUTPUT L & headphone L : MAIN BOARD IC21, IC22, C95,
C98~101, R78, R81~82, R84, CN2
PANEL A BOARD IC3, VR7,
C11~13, R25~26, CN2
OUTPUT R & headphone R : MAIN BOARD IC21, IC22, C103,
C106~109, R90~93, CN2
PANEL A BOARD IC3, VR7,
C16~18, R29~30, CN2
Headphone L & R : MAIN BOARD IC18,JK3
Headphone L : MAIN BOARD IC18, R52, R61, R63,
R87, R146, C81, C233, C236, Q27,
L9, JK3
Headphone R: MAIN BOARD IC18, R53, R58,
R59, R75, R148, C85, C232, C234,
Q28, L10, JK3
OUTPUT L : MAIN BOARD C90, Q4, R79,
R155~158, L11, JK4
OUTPUT R : MAIN BOARD C102, Q5, R89,
R159~162, L12, JK5
10 : Factory Resetting
•Pressing [ENTER] runs the factory reset function.
•Pressing [EXIT] returns to the title screen of the test mode
without running it.
* Factory resetting must be performed at the end of the test
mode.
•The following screen will be displayed during factory
resetting. Never turn off the power when this screen is on.
•After factory resetting, the FLASH ROM (USER MEMORY)
will be checked. If no abnormal condition occurs, the
following screen will be displayed. End the test mode by
turning the power off.

RS-5 Jan. 2001
15
•When an abnormal condition occurs in the FLASH MEMORY
(USER MEMORY), the following screen is displayed.
Check the following parts.
MAIN BOARD IC34
ERROR MESSAGE
This section explains the meaning of the various error messages that
the RS-5 may display, and describes the measures to take when
these appear.
Error Message List
BULK DUMP
Checksum Error
Cause: There is a mistake in the checksum value for the
received System Exclusive message.
Solution: Correct the checksum value.
MIDI Buffer Full
Cause: The data cannot be processed correctly due to an
excessive number of MIDI messages.
Solution: Reduce the number of MIDI messages being
received.
MIDI Communication Error
Cause: There is a problem with the MIDI cable connection.
Solution: Check to make sure no cable has been disconnected,
and that there are no shorts.
Receive Data Error
Cause: MIDI messages could not be received correctly.
Solution: If this same message continues to reappear, it means
that there is a mistake in the content of the MIDI
message.
User Memory Backup Error
Cause: There is an error in the memory used for storage of
User Area and System Setup data.
Solution: Consult your dealer or local Roland service for
repair.
User Memory Damaged
Cause: User Memory data has been corrupted.
Solution: Carry out the Factory Reset operation to restore the
factory settings.

RS-5 Jan. 2001
16
KEYBOARD DISASSEMBLY CIRCUIT BOARD(KEYBOARD)
SK-961-B PARTS LIST
SK-9 CUSHION 61P
SK-9 CHASSIS 61P-B
00893701
00908223
4
3
1
10
9
8
7
6
5
2
No.
2
1
1
4
23
1
1
4
1
61
1
25
10
10
1
5
5
5
Qty.PARTS NAME
70783445
00896990
00896989
40233545
70672834
70672823
00893834
00893823
40233178
00893790
00893778
00893745
00893767
00893756
00893734
PARTS No.
00893723
SK-9 CHASSIS 61P-C ASSY
XP-10 PWB HOLDER
XP-10 KEYBOARD HOLDER
SCREW 3x10 VWH TAPTITE B FE ZC
SK-961 PWB HI ASSY
SK-961 PWB LOW ASSY
SK-9 RUBBER SWITCH 13P
SK-9 RUBBER SWITCH 12P
SK-9 SPRING
SK-9 SHARP KEY
SK-9 NATURAL KEY C'F'
SK-9 NATURAL KEY A
SK-9 NATURAL KEY G
SK-9 NATURAL KEY D
SK-9 NATURAL KEY EB
SK-9 NATURAL KEY CF
8
10
9
8 7
6
5 4 3
2 1

RS-5 Jan. 2001
17
KEYBOARD DISASSEMBLYKEYBOARD CIRCUIT DIAGRAM
Fig.2
Fig.1
Treble sideBass side
RUBBER SWITCH 13P
Air-Escape Groove
RUBBER SWITCH 12P ×4
1
1
29P HI32P LOW
M
S
M
P
M
S
M
P
C7
S.M.7 P.M.7 S.M.6 P.M.6 S.M.5 P.M.5 S.M.4 P.M.4
T7 T6 T5 T4 T3 T2 T1 T0
T7 T6 T5 T4 T3 T2 T1 T0
S.M.3 P.M.3 S.M.2 P.M.2 S.M.1 P.M.1 S.M.0 P.M.0
G#6C6E5G#4C4E3G#2C2
<ATTACHING RUBBER SWITCH and CIRCUIT
BOARD>
Use screws which VWH TAPTIGHT B 3X10MM ZC(#40233545)
to fixed SIRCUIT BOARD in SK-9.
1) Turn over the keyboard as shown in Flg. 1 . Place the
RUBBER SWITCH 12P on 4 chassis, from the left (lowest
note) upward, with respect to slots in the chassis. Make sure
that each switch is aligned with corresponding air groove in the
chassis(Fig.2). Similarly, Place the RUBBER SWITCH 13P on
the right section (high note) chassis.

RS-5 Jan. 2001
18
Fig.4
Fig.3
Positioning reference Pin of chassisPositioning Pin of chassis
PWB Cutout Part
Projecting Part of chassisChassis Hook
******
:Secure with screw : No screw is required unless the chassis hook becomes useless.
Adjacent to PCBS
Fig.5
32 1
Fig.６
Ａ Push
Long nose pliers
SPRING
Fig.７
2) Align notch of the LOW PCB with projection from the chassis
and then insert the PCB into the chassis hook until the chassis's
positioning reference pin (located closest to the connector,
Fig.4) fits into the positioning reference hole of the PCB(Fig.3).
Then, engage all pins with holes. Repeat above steps for the HI
PCB.
3) Secure the LOW and HI PCBs with screws, while holding
the PCB at the center, and starting at the center screw
(1) and then (2) and (3). See Fig.5.
Screw at the locations illustrated.
Note: When using a power screwdriver, set the tightening
torque to 8kgf•cm to firmly secure the PCB without
damaging it. Overtightening will break foil
conductors.
<Removing the keyboard>
Holding the tip of the key, insert a pair of long nose pliers
into the U groove (shaded in Fig.6) and then push the key
in the direction of arrow.
<Installing the keyboard>
Fit the spring on the chassis, place the key as illustrated in
Fig.7 and then push the dotted circle line section in the
direction ofarrow.

RS-5 Jan. 2001
19
BLOCK DIAGRAM
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
ADPV

RS-5 Jan. 2001
20
CIRCUIT BOARD (MAIN BOARD)
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V