Roland Lucina AX-09 User manual

Deutsch Français Italiano Español Português NederlandsEnglish

2
Features
Sounds that you’ll enjoy playing!
• The total of 144 sounds covers all the bases, including not only synthesizer sounds but also
piano, organ, strings, brass, and guitar, all immediately playable for instant enjoyment.
• There are also six highly expressive “Special Tones” as well.
These six high-quality sounds were created speci cally for the Lucina AX-09 (synth lead, poly
synth, synth bass, jazz scat, violin and trombone).
Easy to use and handle!
• Operation is easy — simply turn on the power and choose a sound.
• With a lightweight, stylish body, and support for battery operation, you can play the Lucina
AX-09 anywhere, anytime. Since you can sling the Lucina AX-09 over your shoulder when playing
it, your performances can be more active and versatile.
Enjoy performing more than ever!
• All of the unique expressive capabilities of a traditional synthesizer are at your  ngertips, thanks
to the Lucina AX-09’s D Beam controller, modulation bar, and touch controller.
• You can easily play along with your favorite songs, either by connecting your portable audio
player to the EXT IN jack, or by using the USB memory audio playback function.
How Letters are Shown on the Lucina AX-09
A
A
B
B
C
C
D
D
E
E
F
F
G
G
h
H
i
I
J
J K
L
L
N
M
n
N
o
O
P
P
Q
Q
r
R
S
S
t
T
U
U
u
V W
X
X
Y
Y
Z
Z
Copyright © 2010 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND
CORPORATION.
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” (p. 24) and “IMPORTANT NOTES” (p. 25). These sections provide
important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp
of every feature provided by your new unit, Owner’s Manual should be read in its entirety. The manual should be saved and kept on hand as a
convenient reference.

3
Deutsch Français Italiano Español Português NederlandsEnglish
Contents
Features ...................................2
How Letters are Shown on the Lucina AX-09 . . . . . . . . . 2
Panel Descriptions .........................4
Front Panel .......................................... 4
Bottom Panel ....................................... 5
Rear Panel .......................................... 5
About Batteries ............................6
Installing Batteries .................................. 6
Checking the Remaining Battery Power . . . . . . . . 6
Removing Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Getting Ready .............................7
Connecting the AC Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . 7
Attaching the Strap ................................. 7
Connecting Your Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting Your Headphones . . . . . . . . . . . . . . . . . . . . . . . 8
Turning the Power On ............................... 8
Selecting Tones ............................9
Selecting a Regular Tone ............................ 9
Selecting a Special Tone ............................. 9
Previewing Tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Registering Frequently Used Tones in Memory
(FAVORITE) .........................................10
Using the Performance Functions . . . . . . . . . .11
Raising or Lowering the Key Range by Octaves . . . . . . 11
Raising or Lowering the Key Range by Semitones . . . 11
Using the Touch Controller . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setting the Pitch Range of the Touch
Controller ....................................11
Using the Modulation Bar . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Assigning the Modulation Bar’s Eect . . . . . . . . . 12
Using the D Beam Controller . . . . . . . . . . . . . . . . . . . . . . . . 12
Changing the ASSIGNABLE Setting . . . . . . . . . . . . 12
Using a Foot Pedal .................................13
Preventing Tones from Changing During
Performance (Lock function) . . . . . . . . . . . . . . . . . . . . . . . . 14
Playing Along with a Portable Audio Player . . . . . . . . . 14
Playing Along with an Audio File from USB Memory . 14
Making Audio Player Settings . . . . . . . . . . . . . . . . . 15
Editing the Tone Settings . . . . . . . . . . . . . . . . . .16
Editing the Tone Parameters . . . . . . . . . . . . . . . . . . . . . . . . 16
Adjusting the Tuning . . . . . . . . . . . . . . . . . . . . . .17
Master Tune ........................................17
Key Scale Tune .....................................17
Adjusting the Keyboard’s Touch Sensitivity .17
Setting a Fixed Value for the Keyboard’s Velocity . . . . . 17
Count In / Metronome . . . . . . . . . . . . . . . . . . . .18
Count In Settings ...................................18
Various Settings (Utility) . . . . . . . . . . . . . . . . . .18
Checking the Lucina AX-09’s Version . . . . . . . . . . . . . . . . 18
USB Driver Settings .................................18
Backing Up Lucina AX-09 Settings to USB Memory . . 19
Restoring Lucina AX-09 Settings from USB Memory . 19
Restoring the Factory Settings (Factory Reset) . . . . . . . 19
Connecting Other Equipment . . . . . . . . . . . . .20
Controlling MIDI Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
MIDI Messages that can be Transmitted and
Received .....................................20
Connecting a MIDI Sound Module . . . . . . . . . . . . 20
Making MIDI-related Settings . . . . . . . . . . . . . . . . . 20
Connecting to Your Computer via USB . . . . . . . . . . . . . . 21
Controlling Video (V-LINK) . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Troubleshooting ..........................22
Specications ............................23
Error Message List ........................23
USING THE UNIT SAFELY . . . . . . . . . . . . . . . . . . .24
IMPORTANT NOTES .......................25
Index ....................................26
MIDI Implementation Chart . . . . . . . . . . . . . . .26

4
Panel Descriptions
Front Panel
1 1819
14
11 12 13
7617 82
15
3
16
4 5 9 10
2
1
18
19
7
6
17
8
3
16
16
16
14
15
15
4
5
9
10
1. OCTAVE [+] / [–] Buttons
These buttons raise or lower the keyboard range in steps
of one octave (p. 11).
2. [TRANSPOSE] Button
By holding down this button and pressing the OCTAVE [+],
[–] buttons you can raise or lower the keyboard range in
steps of one semitone (p. 11).
3. Display
This shows the selected tone or mode, or the value of the
parameter you’re editing.
4. [SHIFT] Button
Use this button in conjunction with other buttons to
execute various functions.
5. [SPECIAL TONE] Button
Press this to select special tones.
6. TONE [1]–[6] Buttons
Use these buttons to select the tone group for regular
tones, or to select special tones.
7. [INC/+] / [DEC/–] Buttons
Use these buttons to select variations of the regular tones.
8. FAVORITE [A] / [B] Buttons
Use these buttons to select the FAVORITE memory bank
(p. 10) in which you want to register a favorite tone.
9. [WRITE] Button
This button stores the Lucina AX-09 settings you’ve edited,
or the tone you registered in FAVORITE (p. 10, p. 18).
10. [LOCK] Button
If this button is turned on, you won’t be able to switch
tones. Use this to prevent the tone from being accidentally
switched during a performance (p. 14).
11. USB MEMORY Slot
You can insert USB memory (sold separately) here (p. 15).
12. [VOLUME] Knob
This knob adjusts the volume.
13. D Beam
[PITCH] / [FILTER] / [ASSIGNABLE] Buttons
These buttons turn the D Beam on/o .
By placing your hand above the D Beam you can apply
various e ects to the sound (p. 12).
14. [V-LINK] Button
This button turns V-LINK on/o (p. 21).
15. [AUDIO PLAYER] Button
If you turn this on, you’ll be able to play back audio  les
from USB memory (p. 14).
16. [ / PREVIEW] Button
When the [AUDIO PLAYER] button is lit, this button starts/
stops playback of audio  les in USB memory.
When the [AUDIO PLAYER] button is unlit, this button
starts/stops a preview demo of the currently selected tone.
You can also get a count in to begin sounding by pressing
the modulation bar while you press the [PREVIEW] button.

5
Deutsch Français Italiano Español Português NederlandsEnglish
17. MODULATION BAR / TOUCH CONTROLLER
By pressing the modulation bar, you can apply vibrato. You
can also switch to a Hold e ect that sustains the sound
you’re playing (p. 11).
If you hold your  nger on the touch controller and move it
to left or right, the pitch will change (p. 11).
18. Strap Pin
Attach the included strap to this pin (p. 7).
19. Strap Pin (A)
Attach the included strap to this pin.
Depending on your playing style, you can use either this
pin or the strap pin (B) located on the rear of the Lucina
AX-09 (p. 7).
Bottom Panel
1 2
1
1
2
2
1. Strap Pin (B)
Attach the included strap to this pin.
Depending on your playing style, you can use either this
pin or the strap pin (A) located on the side of the Lucina
AX-09 (p. 7).
2. Battery Compartment
You can install Ni-MH AA rechargeable batteries here (p. 6).
Rear Panel
1 82 3 4 95 106 7
3
2
3
5
10
6
5
7
6
1
8
4
4
9
1. OUTPUT Jacks (L/MONO, R)
The sound of the Lucina AX-09 is output from these jacks.
Connect them to your ampli ed speakers.
To employ monaural output, connect to only the L/MONO
jack.
2. MIDI OUT Connector
If you connect this to another MIDI device, MIDI messages
from the Lucina AX-09 will be transmitted to that device,
allowing you to play it remotely (p. 20).
3. FOOT PEDAL Jack
Connect a separately sold Roland DP-series pedal here.
Alternatively, you can connect an expression pedal (EV-5;
sold separately) (p. 13).
4. [POWER] Switch
This turns the power on/o (p. 8).
If you’re using the included AC adaptor and need to turn
o the power completely, turn o this POWER switch, and
then disconnect the AC adaptor from the outlet.
5. DC IN Jack
Connect the included AC adaptor here (p. 7).
6. Cord Hook
Use this to secure the cord of the included AC adaptor
(p. 7).
7. Security Slot ( )
http://www.kensington.com/
8. USB COMPUTER Connector
Use a USB cable to connect the Lucina AX-09 to your
computer (p. 21).
9. EXT IN Jack
Connect your portable audio player or other audio source
here. The sound that’s input via this jack will be output
from the OUTPUT jacks and the PHONES jack (p. 14).
10. PHONES Jack
Headphones (sold separately) with a stereo mini plug (1/8”
jack) can be connected here (p. 8).

6
About Batteries
If you’re operating the Lucina AX-09 on batteries, you’ll need eight Ni-MH AA rechargeable batteries. The battery
life will di er depending on the conditions of use, but for continuous usage, it is approximately 4 hours.
About rechargeable batteries
When using rechargeable batteries, the battery lifespan will normally become shorter with each recharge cycle. If
the batteries run down soon after being recharged, it’s time to replace them.
Installing Batteries
1. Switch o the Lucina AX-09’s power (p. 8).
2. Remove the cover of the battery compartment
located on the Lucina AX-09’s bottom panel.
While pressing the tabs of the cover, lift the cover up and
remove it.
3. Insert the batteries into the battery compartment.
Make sure to observe the correct polarity (+/– orientation)
for each battery when inserting it.
4. Replace the battery compartment cover.
* When turning the unit upside-down, get a bunch of newspapers
or magazines, and place them under the four corners or at both
ends to prevent damage to the buttons and controls. Also,
you should try to orient the unit so no buttons or controls get
damaged.
* When turning the unit upside-down, handle with care to avoid
dropping it, or allowing it to fall or tip over.
Checking the Remaining Battery
Power
When the remaining battery power runs
low, three dots will blink in the display.
If this indication appears, replace the
batteries as soon as possible.
A while after this indication, the display will indicate “L o ,”
and it will no longer be possible to operate the Lucina
AX-09.
You can also check the remaining battery power in the
following way.
1. Hold down the [SHIFT] button and press the
[LOCK] button.
The display will indicate the remaining battery power as a
percentage (“0”–”100”).
MEMO
• The remaining battery power indication is an
approximation.
• If you check the remaining battery power when the AC
adaptor is connected, the display will always indicate
“100.”
Removing Batteries
To remove the batteries, power o the Lucina AX-09, open
the battery compartment cover, and remove the batteries.
6
Note the following when using batteries
• Do not use alkaline batteries or zinc-carbon batteries.
• The Lucina AX-09 will not operate on batteries if the AC adaptor is connected.
• If batteries are installed, disconnecting or reconnecting the power cord at the AC outlet or disconnecting the DC plug from the Lucina AX-09’s rear panel while the
power is on will cause the power to turn o . You must turn o the power before you connect or disconnect the power cord or AC adaptor.
• Do not allow any objects (e.g.,  ammable material, coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit.
• If used improperly, batteries may explode or leak and cause damage or injury. In the interest of safety, please read and observe the following precautions.
• Carefully follow the installation instructions for batteries, and make sure you observe the correct polarity.
• Avoid using new batteries together with used ones. In addition, avoid mixing di erent types of batteries.
• Remove the batteries whenever the unit is to remain unused for an extended period of time.
• If a battery has leaked, use a soft piece of cloth or paper towel to wipe all remnants of the discharge from the battery compartment. Then install new batteries.
To avoid in ammation of the skin, make sure that none of the battery discharge gets onto your hands or skin. Exercise the utmost caution so that none of the
discharge gets near your eyes. Immediately rinse the a ected area with running water if any of the discharge has entered the eyes.
• Never keep batteries together with metallic objects such as ballpoint pens, necklaces, hairpins, etc.

7
Deutsch Français Italiano Español Português NederlandsEnglish
Getting Ready
Connecting the AC Adaptor
The Lucina AX-09 can operate using the included AC
adaptor, or using Ni-MH AA rechargeable batteries.
1. Make sure that the Lucina AX-09’s power is turned
o (the [POWER] switch is in the OFF position).
2. Turn the [VOLUME] knob all the way to the left
(minimum).
3. Connect the AC adaptor to the Lucina AX-09’s
rear panel DC IN jack, and then plug it into an AC
outlet.
Place the AC adaptor so
the side with the indicator
(see illustration) faces
upwards and the side with
textual information faces
downwards. The indicator
will light when you plug the
AC adaptor into an AC outlet.
To prevent the inadvertent disruption
of power to your unit (should the plug
be pulled out accidentally), and to avoid
applying undue stress to the DC IN jack,
anchor the power cord using the cord hook,
as shown in the illustration.
Attaching the Strap
Attach the strap to the
Lucina AX-09 as shown in the
illustrations below.
1. Attach one end of the included strap to the strap
pin shown in the illustration below.
2. Attach the other end of the included strap to one
of the other two strap pins.
A strap pin is provided in two locations; “A” and “B.” You
can use either one, whichever is more comfortable for you.
For a larger-bodied person, attaching the strap to pin “A”
will provide better stability.
A B
NOTE
If you use strap pin “B,” twist the strap as shown below.
If you attach the strap without twisting it, the strap may
come o of the Lucina AX-09.
Twist
Back of strap Front of strap

8
Connecting Your Speakers
The Lucina AX-09 does not contain an amp or speakers.
In order to produce sound, you’ll need to connect the
rear panel OUTPUT jacks to an audio device such as an
ampli ed speaker system (subsequently referred to as
“speakers”), or use headphones.
Use audio cables (PCS series;
sold separately) to make
connections.
If you’re outputting in monaural, connect only the L/
MONO jack.
* To prevent malfunction and/or damage to speakers or
other devices, always turn down the volume, and turn o
the power on all devices before making any connections.
Connecting Your Headphones
Connect headphones to the rear panel PHONES jack.
You can connect headphones that
have a stereo mini (1/8”) plug.
Turning the Power On
* Once the connections have been completed (p. 8), turn
on power to your various devices in the order speci ed.
By turning on devices in the wrong order, you risk
causing malfunction and/or damage to speakers and
other devices.
1. Minimize the volume of the Lucina AX-09 and your
speakers.
2. On the Lucina AX-09’s rear panel, turn the
[POWER] switch ON.
This unit is equipped with a protection
circuit. A brief interval (a few seconds)
after power up is required before the unit
will operate normally.
3. Turn on the power of your speakers.
4. Use the [VOLUME] knob to adjust the volume
appropriately.
While you play the keyboard
to produce sound, slowly turn
the [VOLUME] knob toward the
right, and adjust the volume
on the Lucina AX-09 and on
your speakers.
Turning the Power O
1. Minimize the volume of the Lucina AX-09 and your
speakers.
2. Turn o the power of your speakers.
3. Turn the Lucina AX-09’s [POWER] switch OFF.

9
Deutsch Français Italiano Español Português NederlandsEnglish
On the Lucina AX-09, each of the sounds you play is called
a “tone.” There are two types of tones: “regular tones” and
“special tones.”
Selecting a Regular Tone
The Lucina AX-09 contains 144 regular tones that bring
you the best sounds of Roland’s synthesizers.
The regular tones are organized into six tone groups, with
24 tones in each group.
1. If the [SPECIAL TONE] button or FAVORITE [A] /
[B] button is lit, press the lit button to turn o its
illumination.
2. Press one of the TONE [1]–[6] buttons to select a
tone group.
The button will light, and that tone group will be selected.
The name of the tone group is printed in black below each
tone button.
MEMO
When you turn on the power, TONE [1] number 1 will
always be selected.
3. Use the [INC/+] / [DEC/–] buttons to select a tone
within the group.
Each group contains tones 1–24, and the number of the
selected tone (1–24) is shown in the display.
Press the [INC/+] button to select the next tone, or press
the [DEC/–] button to select the preceding tone.
MEMO
• For a list of the tones, refer to the “Tone List” at the end
of this manual.
• As indicated by the black characters printed below the
TONE buttons, each tone group is subdivided into two
categories. (For example, the TONE [1] button group
contains the two categories “SYNTH” and “PAD.”)
Each time you hold down the TONE button of the
currently selected (lit) tone group and press the [INC/+]
/ [DEC/–] button, the  rst tone of that category will be
selected.
• By holding down the [INC/+] / [DEC/–] button, you can
select tones rapidly. To select tones even more rapidly,
hold down one button and then press the other button
as well.
Selecting the Rhythm Tone
No. 23–24 of the GUITAR/BASS group is the rhythm
tone. For details, refer to the “Tone List” at the end of this
manual.
Selecting a Special Tone
The Lucina AX-09 contains six “special tones” that were
created speci cally for it.
1. Press the [SPECIAL TONE] button so it’s lit.
2. Press one of the TONE [1]–[6] buttons to select the
desired special tone.
The names of the special tones are printed in blue
characters below each tone button.
MEMO
To return to the regular tones, press the [SPECIAL TONE]
button to turn it o .
Previewing Tones
With the [AUDIO PLAYER] button o , press the [PREVIEW]
button; the button will light and the currently selected
tone will be played using a demo phrase that’s suitable for
that tone.
To stop the phrase before it has  nished playing, press the
[PREVIEW] button once again to turn o its illumination.
Selecting Tones

10
Registering Frequently Used
Tones in Memory ( FAVORITE)
The Lucina AX-09 provides “FAVORITE memory locations”
that allow you to register twelve of the tones. If you use
this to register the tones that you use frequently, you’ll be
able to select those tones quickly and easily at any time.
Your settings for volume and reverb can also be registered
along with the tone selections in the FAVORITE memory
locations (p. 16).
MEMO
Only regular tones can be registered in FAVORITE
memory.
Registering a tone as a FAVORITE
FAVORITE memory contains two banks, A and B; you can
register six tones in each bank.
1. Select the tone that you want to register in a
FAVORITE memory location.
2. Press the [WRITE] button to make it light.
3. Press the FAVORITE [A] / [B] button to select the
bank in which you want to register the favorite.
The FAVORITE button you pressed will light.
The display will indicate “A -” (bank “A”) or “b -” (bank
“B”).
4. Press one of the TONE [1]–[6] buttons to select the
memory location in which you want to register the
favorite tone.
The button you pressed will light, and the tone will be
registered in that FAVORITE memory location. The [WRITE]
button will go out.
MEMO
To return to regular tones, press the lit FAVORITE [A] /
[B] button to turn o its illumination.
Recalling a FAVORITE tone
Here’s how to recall a tone you’ve registered in FAVORITE
memory.
1. Press the FAVORITE [A] / [B] button to select the
bank in which you registered the tone you want
to recall.
The FAVORITE button you pressed will light.
2. Press one of the TONE [1]–[6] buttons to select a
FAVORITE memory location from the current bank.
You can also use the [INC/+] / [DEC/–] buttons to
consecutively select FAVORITE memory locations in the
same bank.
MEMO
To return to regular tones, press the lit FAVORITE [A] /
[B] button to turn o its illumination.

11
Deutsch Français Italiano Español Português NederlandsEnglish
The Lucina AX-09 provides various performance functions
that can make your performance more expressive.
Raising or Lowering the Key
Range by Octaves
You can raise or lower the range of the keyboard in steps
of one octave, for a maximum of three octaves upward or
downward.
Value -3–3
1. Press an OCTAVE [+] / [–] button.
The display will indicate a value.
The OCTAVE [+] button will light if the octave setting is
in the “+” direction; the OCTAVE [–] button will light if the
octave setting is in the “–” direction.
MEMO
To return the octave setting to “0,” press the OCTAVE [+]
and [–] buttons simultaneously.
The OCTAVE [+] / [–] button will go out, and the
keyboard will return to its normal range of pitches.
Raising or Lowering the Key
Range by Semitones
You can raise or lower the range of the keyboard in steps
of a semitone.
This function can be convenient when you need to play a
song in an unfamiliar key signature.
Value -5–6
1. Hold down the [TRANSPOSE] button.
The current setting will blink in the display.
2. Hold down the [TRANSPOSE] button, and press
the OCTAVE [+] / [–] button to set the desired
value.
3. The value will be applied when you release the
[TRANSPOSE] button.
The [TRANSPOSE] button will be lit if you’ve speci ed a
value other than “0.”
MEMO
To return the setting to “0,” hold down the [TRANSPOSE]
button and press the OCTAVE [+] and [–] buttons
simultaneously.
The [TRANSPOSE] button will go out, and the keyboard
will return to its normal range of pitches.
Using the Touch Controller
By placing your  nger on the touch controller and moving
it to left or right, you can vary the pitch of the sound you’re
playing. Touching the left side of the controller will lower
the pitch, and touching the right side will raise the pitch.
Setting the Pitch Range of the Touch Controller
By following the procedure below, you can set the range
of pitches within which the pitch can be changed when
you operate the Touch Controller. This setting is speci ed
in terms of a value in semitones. For example, if you specify
a value of “12,” the pitch will rise by a whole octave when
you touch the rightmost edge of the Touch Controller (12
semitones is equivalent to one octave).
1. While holding down [SHIFT], touch the Touch
Controller.
The value currently set for the pitch range will appear,
blinking, in the display.
2. Continue holding down the [SHIFT] button, and
use the [INC/+] / [DEC/–] buttons to change the
setting.
Value 0–24
3. Release the [SHIFT] button.
4. To save this setting, hold down the [SHIFT] button
and press the [WRITE] button.
Using the Modulation Bar
You can apply vibrato by pressing the modulation bar
while you play the Lucina AX-09.
MEMO
The same e ect is applied to all tones. However, if
you’ve selected 4 VIOLIN or 5 TROMBONE of the special
tones, the dynamics (expression) will change in a way
that’s distinctive of that instrument, allowing you to
play with highly realistic expressiveness.
play with highly realistic expressiveness.
Using the Performance Functions

12
Assigning the Modulation Bar’s E ect
You can also change the assignment of the modulation
bar so that it will hold notes or hold notes while applying
vibrato.
1. Hold down the [SHIFT] button and press the
modulation bar.
The current setting will blink in the display.
2. Continue to hold down the [SHIFT] button, and
use the [INC/+] / [DEC/–] buttons to assign the
desired e ect.
This speci es the e ect that will be applied when you
operate the modulation bar.
Value Explanation
NoD Vibrato will be applied to the sounds you’re playing.
hLD The sounds you’re playing will be sustained while you
press the modulation bar.
CNB Vibrato and Hold will both be applied to the sounds
you’re playing.
MEMO
The same e ect is applied to all tones. However, if
you’ve selected 4 VIOLIN or 5 TROMBONE of the special
tones, the dynamics (expression) of the instrument will
be modi ed instead of the vibrato e ect.
3. Release the [SHIFT] button.
4. To save this setting, hold down the [SHIFT] button
and press the [WRITE] button.
Using the D Beam Controller
By moving your hand above the D Beam controller’s
sensor, you can modify the sound by applying the e ect
you’ve assigned to the D Beam.
The D Beam controller’s eff ective range
The illustration below shows the approximate e ective
range of the D Beam controller.
No e ect will be obtained if you position your hand
outside this e ective range.
* The usable range of D Beam controller will become
extremely small when used under strong direct
sunlight. Please be aware of this when using the D Beam
controller outside.
1. Press one of the following buttons to select the
function that you want to control using the
D Beam controller.
Value Explanation
PITCH Moving your hand above the D Beam controller
will vary the pitch of the sounds you play.
FILTER
Moving your hand above the D Beam controller
will vary the tonal character of the sounds you
play.
* For some tones, the change in character
may be di cult to notice.
ASSIGNABLE The D Beam controller will transmit the assigned
function or control change message.
2. While you play the keyboard, move your hand
slowly up and down above the D Beam controller.
The button you pressed in step 1 will blink.
3. To turn o the D Beam controller, once again press
the button you pressed in step 1; it will go out.
Changing the ASSIGNABLE Setting
You can assign a MIDI control change number (CC) or
function to the [ASSIGNABLE] button, and use the D Beam
controller to control that parameter in real time.
1. Hold down the [SHIFT] button and press
[ASSIGNABLE].
The currently assigned function will blink in the display.
2. Continue to hold down the [SHIFT] button,
and use the [INC/+] / [DEC/–] button to specify
the desired function or parameter that will be
controlled by the D Beam controller.
Display Value Explanation
C01 CC01
( MODULATION) Apply vibrato.
C05 CC05
( PORTA TIME)
Control the portamento time
over which the pitch changes
between notes when playing with
portamento.
C07 CC07 ( VOLUME) Control the volume.
C10 CC10 ( PAN) Control the panning.
C11 CC11 ( EXPRESSION) Control the expression.
C64 CC64 ( HOLD) Sustain the notes.
C65 CC65
( PORTAMENTO)
Smoothly connect the pitch from one
note to the next.

13
Deutsch Français Italiano Español Português NederlandsEnglish
Display Value Explanation
C66 CC66 ( SOSTENUTO) Sustain the notes that are currently
being held down.
C71 CC71 ( RESONANCE)
Control the resonance. Increasing
the resonance value will produce
a distinctive tonal character that is
typical of a synthesizer.
C72 CC72 ( RELEASE TIME)
Control the time from note-o (when
the key is released) until the sound
is no longer heard (i.e., the release
time).
C73 CC73 ( ATTACK TIME) Control the sharpness (attack speed)
with which the sound begins.
C74 CC74 ( CUTOFF)
Control the cuto . Higher values will
make the sound harder (brighter);
lower values will make the sound
softer (more mellow).
AFt AFTERTOUCH
(Default)
Apply the most suitable e ect for
each of the Lucina AX-09’s tones.
Adb ADLIB
By  ngering a chord and moving
your hand above the D Beam
controller, you can produce an
arpeggio of that chord.
The distance from the D Beam
controller will determine the octave
span of the chord that is played, and
the speed at which you move your
hand up and down will determine
the speed at which the chord is
arpeggiated.
For example if you use your right
hand to hold down the four notes
“C D E G” and move your left hand
above the D Beam controller, a
phrase such as “C D E G C D E G C D E
G...” will play.
SLo SOLO SYNTH
The Lucina AX-09 will operate as a
monophonic synthesizer whose pitch
can be controlled by moving your
hand above the D Beam controller.
MEMO
By holding down the [INC/+] / [DEC/–] button you can
choose this setting rapidly. To choose even faster, hold
down the button and press the other button as well.
3. Release the [SHIFT] button.
4. To save this setting, hold down the [SHIFT] button
and press the [WRITE] button.
Using a Foot Pedal
If you connect a pedal switch (DP series; sold separately)
to the FOOT PEDAL jack, you can hold down the pedal to
make notes continue sustaining even after you release the
keyboard.
Alternatively, you can use the pedal to apply numerous
other e ects.
Connecting a foot pedal
MEMO
Alternatively, you can connect an expression pedal
(EV-5) instead of a pedal switch (DP series).
NOTE
Use only the speci ed expression pedal (EV-5; sold
separately). By connecting any other expression pedals,
you risk causing malfunction and/or damage to the
unit.
Specifying the foot pedal assignment
Hold down the [SHIFT] button and press the [V-LINK]
button twice; the screen will indicate “PDL,” allowing you
to assign the e ect applied by the foot pedal.
You can assign the following functions to the pedal.
To save this setting, hold down the [SHIFT] button and
press the [WRITE] button.
Display Value Explanation
C01 CC01 ( MODULATION) Apply vibrato.
C05 CC05 ( PORTA TIME)
Control the portamento time over
which the pitch changes between
notes when playing with portamento.
C07 CC07 ( VOLUME) Control the volume.
C10 CC10 ( PAN) Control the panning.
C11 CC11 ( EXPRESSION) Control the expression.
C64 CC64 ( HOLD) Sustain the notes.
C65 CC65 ( PORTAMENTO) Smoothly connect the pitch from one
note to the next.
C66 CC66 ( SOSTENUTO) Sustain the notes that are currently
being held down.

14
Display Value Explanation
C71 CC71 ( RESONANCE)
Control the resonance. Increasing
the resonance value will produce
a distinctive tonal character that is
typical of a synthesizer.
C72 CC72
( RELEASE TIME)
Control the time from note-o (when
the key is released) until the sound is
no longer heard (i.e., the release time).
C73 CC73
( ATTACK TIME)
Control the sharpness (attack speed)
with which the sound begins.
C74 CC74 ( CUTOFF)
Control the cuto . Higher values will
make the sound harder (brighter);
lower values will make the sound
softer (more mellow).
AFt AFTERTOUCH Apply the most suitable e ect for each
of the Lucina AX-09’s tones.
PUP PEDAL UP Select the tone of the next tone
number.
PDn PEDAL DOWN Select the tone of the preceding tone
number.
MEMO
With the factory settings, the foot pedal is assigned to
C64 (Hold).
If using a foot pedal not made by Roland
If you’re using a foot pedal that was made by a
manufacturer other than Roland, the pedal polarity might
be reversed, so that the operations that occur when you
press and release the pedal are the opposite of what you
expect. If so, hold down the [SHIFT] button and press the
[V-LINK] button three times to make the display indicate
“PoL.” Then use the [INC/+] / [DEC/–] buttons to make the
display indicate “rEu.”
To save this setting, hold down the [SHIFT] button and
press the [WRITE] button.
Value Explanation
Std (Standard) Pedals made by Roland
rEu (Reverse) Pedals with a polarity opposite to that
of Roland pedals
Preventing Tones from Changing
During Performance ( Lock function)
You can lock the tone selected on the Lucina AX-09 to
prevent a di erent sound from being selected even if you
accidentally press a tone button while performing.
1. Hold down the [LOCK] button until it lights.
The Lock function will turn on; in this state, button
operations will not switch the tone.
To re-enable tone switching, hold down the button once
again until [LOCK] button goes out.
Playing Along with a Portable
Audio Player
You can connect your portable audio player, and play the
Lucina AX-09 along with your favorite songs.
1. Connect your portable audio player to the Lucina
AX-09’s EXT IN jack.
Use a stereo mini-plug
(1/8”) cable to connect
your player to the EXT
IN jack.
2. Play back a song on your portable audio player,
and play along on the Lucina AX-09.
Use the controls of your player to adjust the volume and
select songs.
* When connection cables with resistors are used, the
volume level of equipment connected to the inputs (EXT
IN) may be low. If this happens, use connection cables
that do not contain resistors.
Playing Along with an Audio
File from USB Memory
The Lucina AX-09 can play back audio
 les (MP3, WAV, AIFF) that you’ve copied
to USB memory from your computer,
allowing you to play along with your
favorite songs.
Copying audio  les from your
computer to USB memory
You’ll need to copy the audio  les from your computer to
the root level of your USB memory.
MP3, WAV, AIFF
Copy to a USB drive

15
Deutsch Français Italiano Español Português NederlandsEnglish
Audio fi les that can be played
MP3
Format MPEG-1 audio layer 3
Sampling
Frequency 44.1 kHz
Bit Rate 32/40/48/56/64/80/96/112/128/160/192/224/256/320 kbps,
VBR (Variable Bit Rate)
WAV, AIFF
Sampling
Frequency 44.1 kHz
Bit Rate 8/16/24 -bit
Insert the USB memory
1. Insert your USB memory into the USB MEMORY
slot as shown in the illustration below.
NOTE
• Never insert or remove a USB memory while this unit’s
power is on. Doing so may corrupt the unit’s data or the
data on the USB memory.
• Carefully insert the USB memory all the way in—until it
is  rmly in place.
• Use USB memory sold by Roland. We cannot guarantee
operation if other products are used.
Play back audio  les
1. Insert the USB memory containing the copied
audio  les into the Lucina AX-09’s USB MEMORY
slot.
2. Press the [AUDIO PLAYER] button.
The [AUDIO PLAYER] button will light and the [ ]
button will blink; now you can play back audio  les from
USB memory.
If you press the [AUDIO PLAYER] button once again, the
button will go out; now audio  les will not be played.
MEMO
The [ ] button will not blink if USB memory is not
inserted, or if the USB memory contains no song that
can be played.
3. Select a song.
When you hold down the [AUDIO PLAYER] button, the
display will show the  rst three characters of the  le name
of the currently selected audio  le.
Continue holding down the [AUDIO PLAYER] button, and
press the [INC/+] button to jump to the next song, or press
the [DEC/–] button to jump to the beginning of the song
(or the preceding song if you’re already at the beginning
of the song).
MEMO
The songs will be ordered by their  le name (in the
order of numerals, uppercase letters, and lowercase
letters).
4. Play or stop the song.
When you press the [ ] button, the button that was
blinking will light, and the selected audio  le will play.
If you press the [ ] button during playback, the lit
button will blink, and playback will stop.
If you press the [ ] button once again, playback will
resume from where it was stopped.
Switching songs during playback
During playback, you can hold down the [AUDIO PLAYER]
button and press the [DEC/–] button to interrupt playback
and return to the beginning of the current song. Similarly,
pressing the [INC/+] button will move to the beginning of
the next song, and resume playback.
MEMO
If you hold down the [AUDIO PLAYER] button and press
the [DEC/–] button at the beginning of the song, you’ll
return to the beginning of the preceding song.
Making Audio Player Settings
1. Hold down the [SHIFT] button and press the
[AUDIO PLAYER] button; the current audio player
setting will blink in the display.
2. Continue holding down the [SHIFT] button, and
press the [AUDIO PLAYER] button once again to
switch parameters.
After a brief interval, the value will appear; continue
holding down the [SHIFT] button, and use the [INC/+] /
[DEC/–] buttons to edit the value.
Parameter Value Explanation
LuL 0–127 Audio  le playback volume level
PLY 1 P (SINGLE PLAY),
C P (CHAIN PLAY)
Choose whether playback will stop at
the end of the selected song (SINGLE
PLAY) or continue playing to the next
song (CHAIN PLAY).
3. To save this setting, hold down the [SHIFT] button
and press the [WRITE] button.

16
Editing the Tone Parameters
You can edit tone parameters such as the volume and
reverb for a regular tone, and save your settings in a
FAVORITE memory location (p. 10).
* You can’t edit the tone parameters of a special tone.
1. Select the regular tone whose tone parameters
you want to edit (p. 9).
2. Hold down the [SHIFT] button and press the TONE
button of the tone you selected in step 1 (i.e., the
TONE button that’s lit).
The parameter name (P S ) will blink in the display, and
then its value (oFF or o N ) will appear.
3. Continue holding down the [SHIFT] button, and
press the same TONE button to switch parameters.
The parameters will switch from top to bottom of the
“Parameter” column in the following table.
* Don’t release your nger from the [SHIFT] button while
making this setting.
Parameter Value Explanation
P S OFF, ON
Portamento Switch
Portamento is an eect that creates a
smooth change in pitch from one note
to the next.
PtN 0–127
Portamento Time
This species the time over which
the pitch will change when using
portamento. Higher values will lengthen
the time over which the pitch will reach
the next note.
uoL 0–127 Volume
This species the volume of the tone.
rEu 0–127
Reverb
This eect adds the reverberation that
is characteristic of a performance in a
large hall. Higher values produce deeper
reverberation.
rEL -64–63
Release Time (*1)
This adjusts the time from note-o
(i.e., when you release the key) until
the sound disappears. Higher values
produce a longer release time.
A t -64–63
Attack Time (*1)
This adjusts the sharpness (speed) at
which the sound begins. Higher values
produce a more gentle attack.
CUt -64–63
Cuto (*1)
Increasing the cuto value will make
the sound harder (brighter); decreasing
it will make the sound more mellow
(darker). Use this parameter to make
adjustments if the sound is too mued
or too bright.
rES -64–63
Resonance (*1)
Increasing the resonance value will
produce a distinctive tonal character
that is typical of a synthesizer. If you
want to emphasize the eect of
resonance, it’s a good idea to slightly
lower the cuto.
*1 The values you specify here are an adjustment relative to the value
assigned by each tone. If this value is set to 0, the parameter will be as
specied by the tone’s own settings.
4. When the parameter value appears, continue
holding down the [SHIFT] button and use the
[INC/+] / [DEC/–] buttons to edit the value.
MEMO
• You can make the value change more quickly by
holding down the [INC/+] / [DEC/–] button. If you want
the value to change even faster, hold down the button
and press the other button as well.
• Even while editing the value, you can play the keyboard
to hear the result.
5. Release the [SHIFT] button.
* If you select a dierent sound or turn o the Lucina
AX-09’s power in this state, the changes you made will
be lost. If you want to keep your changes, you must store
them in a FAVORITE memory location as follows.
6. Press the [WRITE] button.
The [WRITE] button will blink.
7. Press the FAVORITE [A] button or [B] button to
select a bank.
8. Press one of the TONE [1]–[6] buttons to select the
memory location in which you’ll store the settings.
When the [WRITE] button goes out, the settings have been
stored.
Editing the Tone Settings

17
Deutsch Français Italiano Español Português NederlandsEnglish
Master Tune
This is the overall tuning setting for the entire Lucina
AX-09. With the factory settings, this is set to 440 Hz. The
displayed value is the frequency of the A4 key (middle “A”).
Value 415.3–466.2 Hz
1. Hold down the [SHIFT] button and press the
[TRANSPOSE] button.
The display will indicate “Ntn,” and then the current value
of Master Tune will blink.
The display shows only the last three digits (the initial
numeral of “4” is omitted).
2. Continue holding down the [SHIFT] button, and
use the [INC/+] / [DEC/–] buttons to adjust the
tuning value.
MEMO
• You can make the value change more quickly by
holding down the [INC/+] / [DEC/–] button. If you want
the value to change even faster, hold down the button
and press the other button as well.
• Even while editing the value, you can play the keyboard
to hear the result.
3. Release the [SHIFT] button.
4. To save this setting, hold down the [SHIFT] button
and press the [WRITE] button.
Key Scale Tune
You can choose either equal temperament or an Arabian
scale as the keyboard tuning.
Value Explanation
EQL Equal temperament
ArB Arabian scale
1. Hold down the [SHIFT] button and press the
[TRANSPOSE] button twice.
The display will indicate “ E Y ”; then the current setting of
Key Scale Tune will blink.
2. Continue holding down the [SHIFT] button, and
use the [INC/+] / [DEC/–] buttons to choose the
desired value for Key Scale Tune.
MEMO
Even while editing the value, you can play the keyboard
to hear the result.
3. Release the [SHIFT] button.
4. To save this setting, hold down the [SHIFT] button
and press the [WRITE] button.
Adjusting the Tuning
Adjusting the Keyboard’s Touch Sensitivity
Setting a Fixed Value for the Keyboard’s
Velocity
In order to play using notes that all have a uniform level
(velocity), regardless of the amount of force you use when
pressing keys, carry out the following procedure.
1. Hold down the [SHIFT] button and press the
[V-LINK] button once.
The display will indicate “uEL,” and then the value of the
current setting will appear.
2. Continue holding down the [SHIFT] button, and
use the [INC/+] / [DEC/–] buttons to change the
setting.
Value Explanation
rAL (Real) Notes reecting the actual amount of force you use
when pressing keys will be output.
1–127
Notes having the specied velocity value will be output,
regardless of the amount of force you use when pressing
keys.
3. Release the [SHIFT] button.
4. To save this setting, hold down the [SHIFT] button
and press the [WRITE] button.

18
Checking the Lucina AX-09’s
Version
Here’s how to check the Lucina AX-09’s version.
1. While holding down the FAVORITE [A], [B], and
[WRITE] buttons simultaneously, turn on the
Lucina AX-09’s power.
The display will indicate “UtL”; the Lucina AX-09 will be in
Utility mode.
2. Press the TONE [1] button.
The display will indicate the version of your Lucina AX-09.
If you want to continue playing the Lucina AX-09, turn o
the power and wait several seconds before turning it on
again.
USB Driver Settings
When using a USB cable to connect the
Lucina AX-09 to your computer, you can
choose whether to use the standard USB
driver that’s provided by your computer
or the USB driver provided by Roland.
MEMO
For details on connecting the Lucina AX-09 to your
computer via USB, refer to “Connecting to Your
Computer via USB” (p. 21).
1. While holding down the FAVORITE [A], [B], and
[WRITE] buttons simultaneously, turn on the
Lucina AX-09’s power.
The display will indicate “UtL”; the Lucina AX-09 will be in
Utility mode.
2. Press the TONE [2] button.
The display will indicate “dru”; then the current value is
shown and the [WRITE] button will blink.
3. Use the [INC/+] / [DEC/–] buttons to choose the
desired setting.
Value Explanation
GEn (Generic)
(Default)
Choose this if you’re using the standard USB driver
provided by your computer.
Normally you’ll use this mode.
unD (Vendor) Choose this if you’re using the USB driver
downloaded from the Roland website.
4. Press the [WRITE] button to save the setting.
5. Turn the Lucina AX-09’s power o , then on again.
Now you’ll be able to use the USB driver you choose.
Various Settings ( Utility)
Count In / Metronome
“Count in” refers to a feature that counts you in to the
beginning of the performance. To have a two-measure
count in be sounded, press the modulation bar while you
press the [PREVIEW] button.
Note that, if you wish, you can have a metronome be
sounded instead—simply change the Count Mode to Ntr
(METRONOME) using the setting below. The metronome
will continue to sound until you press the [PREVIEW]
button a second time.
* A count in will not be sounded when the [AUDIO
PLAYER] button is lighted.
Count In Settings
1. Hold down the [SHIFT] button and press the
[PREVIEW] button; the current count in setting will
blink in the display.
2. Continue holding down the [SHIFT] button, and
press the [PREVIEW] button once again to switch
parameters.
After a brief interval, the value will appear; continue
holding down the [SHIFT] button, and use the [INC/+] /
[DEC/–] buttons to edit the value.
Parameter Value Explanation
Cnt
oFF(OFF),
Cin(COUNT IN),
Ntr (METRONOME)
Count mode
Determines whether count in
or metronome will sound
bPN 20–250 Tempo of count
bAt 0.4, 2.4, 3.4, 4.4, 5.4, 6.4, 7.4 Time signature of count
(2.4 indicates 2/4 time)
LuL 0–10 Volume of count
tyP
1 (Electronic metronome)
2 (Mechanical metronome)
3 (Pulse)
4 (Beep)
5 (Cowbell)
6 (Stick)
Sound used for count
3. To save this setting, hold down the [SHIFT] button
and press the [WRITE] button.
MEMO
To have the tempo of the count be shown in the
display, hold down the [PREVIEW] button. While in this
state, you can set a new tempo by tapping the [SHIFT]
button at least four times at the desired tempo; or you
can set it using the [INC/+] and [DEC/-] buttons.

19
Deutsch Français Italiano Español Português NederlandsEnglish
Backing Up Lucina AX-09
Settings to USB Memory
Here’s how to back up your Lucina
AX-09 settings and the tone settings in
FAVORITE memory (p. 16) to USB memory
(sold separately).
1. Insert your USB memory into the USB MEMORY
slot (p. 15).
2. While holding down the FAVORITE [A], [B], and
[WRITE] buttons simultaneously, turn on the
Lucina AX-09’s power.
The display will indicate “UtL”; the Lucina AX-09 will be in
Utility mode.
3. Press TONE [3] button.
The display will indicate “bUp” and the [WRITE] button will
blink.
4. Press the [WRITE] button.
The backup will begin.
5. When the display indicates “DnE,” turn the Lucina
AX-09’s power o , then on again.
MEMO
If USB memory is not inserted in the Lucina AX-09 when
you press the [WRITE] button, the display will indicate
“Err.”
Restoring Lucina AX-09 Settings
from USB Memory
Here’s how settings you saved as
described in “Backing Up Lucina AX-09
Settings to USB Memory” (p. 19) can be
restored to the Lucina AX-09.
1. Insert the USB memory containing the backed up
settings into the USB MEMORY slot (p. 15).
2. While holding down the FAVORITE [A], [B], and
[WRITE] buttons, turn on the Lucina AX-09’s power.
The display will indicate “UtL”; the Lucina AX-09 will be in
Utility mode.
3. Press the TONE [4] button.
The display will indicate “rSt” and the [WRITE] button will
blink.
4. Press the [WRITE] button.
The [WRITE] button will light, and the restore operation
will begin.
5. When the display indicates “DnE,” turn the Lucina
AX-09’s power o , then on again.
MEMO
If USB memory is not inserted in the Lucina AX-09
when you press the [WRITE] button, or if backup data
does not exist in the appropriate location of the USB
memory, the display will indicate “Err.”
Restoring the Factory Settings
( Factory Reset)
Here’s how to return the Lucina AX-09 to its factory-set
state.
NOTE
• When you execute this operation, all settings you’ve
modi ed since purchasing the Lucina AX-09, including
the tone settings you’ve stored in FAVORITES, will be
lost.
• If you want to keep your settings, be sure to back them
up to USB memory before you execute the factory
reset.
“Backing Up Lucina AX-09 Settings to USB Memory” (p.
19)
1. While holding down the FAVORITE [A], [B], and
[WRITE] buttons, turn on the Lucina AX-09’s power.
The display will indicate “UtL”; the Lucina AX-09 will be in
Utility mode.
2. Press the TONE [5] button.
The display will indicate “FCt,” and the [WRITE] button
will blink.
3. Press the [WRITE] button.
The [WRITE] button will light, and the factory reset will
begin.
NOTE
While the [WRITE] button is lit, the factory reset is being
executed. Never turn o the power during this time.
The Lucina AX-09 may malfunction if you do so.
4. When the display indicates “DnE,” turn the Lucina
AX-09’s power o , then on again.

20
Controlling MIDI Devices
If you’re using the Lucina AX-09 by itself, there’s no need
for you to have a detailed understanding of MIDI. The
following explanation of MIDI is provided for those who
wish to connect the Lucina AX-09 to other MIDI devices
and control them.
MEMO
MIDI stands for Musical Instrument Digital Interface,
and is a global standard that allows electronic musical
instruments and computers to exchange performance
data.
“MIDI Implementation Chart” (p. 26) is a chart that
provides an easy way of checking which MIDI messages
the Lucina AX-09 is able to receive. By comparing the
MIDI implementation charts of the Lucina AX-09 and
some other MIDI device, you can see which messages
are compatible between the two devices.
MIDI Messages that can be
Transmitted and Received
The Lucina AX-09 can transmit and receive the following
MIDI messages.
MEMO
The Lucina AX-09 always receives MIDI messages from
the USB COMPUTER connector.
MIDI message Explanation
Note On/O (*1) Transmission Key on/o messages
Velocity Transmission Strength with which you play the key
Aftertouch
Transmission
Channel aftertouch messages
transmitted by the D Beam [ASSIGNABLE]
button assigned to “AFt” or by the
PEDAL. (This message is not transmitted
by the keyboard.)
Receive
Channel aftertouch, polyphonic
aftertouch.
Cannot be speci ed from the Lucina
AX-09
Program Change Transmission
Bank Select (*2) Transmission Cannot be speci ed from the Lucina
AX-09
Modulation CC01, transmission: MODULATION BAR
CC01 (Modulation)
Transmission
Control change number assigned to
the D Beam [ASSIGNABLE] button or to
the PEDAL
CC05 (Porta-Time)
CC07 (Volume)
CC10 (Panpot)
CC11 (Expression)
CC64 (Hold)
CC65 (Porta-Sw)
CC66 (Sostenute)
CC71 (Resonance)
CC72 (ReleaseTime)
CC73 (AttackTime)
CC74 (Cuto )
*1 Local control is always on. It cannot be turned o . If you want to control a
connected external sound module without playing the Lucina AX-09’s own
sounds, you can either disconnect the Lucina AX-09’s OUTPUT jacks, lower the
Lucina AX-09’s volume, or lower the volume of the connected amp or mixer.
*2 The transmitted program change number and bank select data (CC00, CC32)
cannot be speci ed from the Lucina AX-09, but when you select an internal
tone, that tone’s program change number and bank select data (CC00, CC32;
see the “Tone List” at the end of this manual) will be transmitted according to
the MIDI settings (p. 20).
Connecting a MIDI Sound Module
1. Use a MIDI cable to connect the Lucina AX-09’s
MIDI OUT connector to the MIDI IN connector of
the MIDI sound module you want to control.
MIDI Sound Module
MIDI IN connector
As necessary, connect an amp or speakers to the MIDI
sound module or synthesizer you’re using. For details,
refer to the owner’s manual of the sound module (or other
device) you’re using.
Making MIDI-related Settings
1. Hold down the [SHIFT] button and press the
[V-LINK] button the appropriate number of times
to access the desired MIDI setting; four times for
“C h ,”  ve times for “B n ,” or six times for “P C .”
2. Continue holding down the [SHIFT] button, and
use the [INC/+] / [DEC/–] buttons to edit the
setting.
Parameter Value Explanation
C h 1–16
(Default: 1) MIDI channel setting
B n OFF, ON
(Default: OFF)
Speci es whether MSB/LSB will be
transmitted
P C OFF, ON
(Default: ON)
Speci es whether program change
data will be transmitted
3. Release the [SHIFT] button.
4. To save this setting, hold down the [SHIFT] button
and press the [WRITE] button.
Connecting Other Equipment