Rollei DF-S 100 SE - User manual

Version 1.08

Index
I. Unpack Rollei DF-S100 SE Scanner........................................2
II. Install film into the film holder.............................................3
III. Quick Start..........................................................................7
IV. Operaon Guide................................................................12
V. Specificaon.........................................................
.............37
INFORMATION:
The ROLLEI DFS 100 SE Film Scanner is conceived for private use only and not
for the ulizaon of commercial purpose.
-1-

/hŶƉĂĐŬZŽůůĞŝ&Ͳ^ϭϬϬ^
ġġġġġRollei DF-S100 SE NegaƟve/Slide Film Holder œŢűŪťġġŔŭŪťŦġŇŦŦťŦų
USB power adapter USB/Video cable Clean brush Quick Guide&'
Note
We strongly suggest using a clean, dry, non-
alcohol coƩon swab to clean the glass surface
periodically to produce a clear image during
operaƟon.
Clean dust from FilmScanner back light, to use the
clean brush to wipe the dust.
Dust or dirt from the negaƟve, slide Įlms and
cover trays may aīect the scanned image quality,
please make sure the materials are cleaned
before inserƟng into the scanner.
Please Įnd recommend, processional purger from photo store to clean the dust on
Įlms if any to avoid damaging the only one copy of old Įlms.
-2-
Rollei DF-S190 SE
User Manual

II. Install film into the film holder
●
●
Install the Slide into holder
1. Open the slide holder as illustrated
2. Put slide into posive slide slot 3. Close the film holder
●
Install the Negave Film into holder
1. Open the film holder as illustrated
-3-

2. Install film into negave film slot 3. Close the film holder
●
Install the Rapid Slide Feeder:
1. Take out the Rapid Slide Feeder from package
2. Put slides into slide slot, use 3. Insert the Slide Feeder into the unit
Level bar to eject slide
-4-

Note
To avoid mirror image, follow the serial numbers (from leto right) on top of film
when install negave film into holder
If the image is upside down [see fig.2], the image can be corrected by Flip funcon in
hard key of device before capture, or enter playback edit menu aer capture [see
fig.3].
-5-
Figure 1
Figure 2

●
Press hard key on top of device in live view
Figure 3
-6-
<Up> then <Down>
buon to perform
Flip
Flip

III. Quick Start
-7-
Right/+ buon
Film Slot
OK buon
SD card Slot
Le/- buon
Power buon
USB port
TV out jack
Power status LED

1. Put Film onto the film cartridge
2. Insert the film cartridge into Rollei DF-S100 SE
-8-

3. Connect USB cable to Rollei DF-S100 SE
4. Turn on Device by power buon
(Important: insert SD card before turning the device on)
-9-

5. Press
Film Type to set the correct film type before proceeding)
OK buon to capture the image (Important: refer to Chapter 3
6. Follow the menu on display for scanning
-10-

7. Aer finished the capture, take out the SD card which stored capture
images
8. Or read picture from PC by MSDC mode
-11-

IV. Operaon Guide
Home: Main menu
●
Capture: capture mode (default)
●
Playback: playback mode
●
Film Type: define the film type which loaded in cartridge
●
USB mode: MSDC (Mass Storage Device Class) mode
●
Seng: TV out and format opon
1. Capture
Aer welcome page, above menu will remain. User can press up/down buon for desired menu.
-12-
Capture
Playback
Film Type
USB mode Seng
Capture

1.1 Capture: <Up>/<Down> (Hard Key)
●
Press <Up> buon to enter Mirror/Flip adjustment (see Chapter 1.2)
●
Press <Down> buon to enter Brightness/Color adjustment (see Chapter 1.3)
-13-
<
Up> Right/Up
<Down>
Le/Down
<Up>
<Down>
<OK> buon
Go Next

1.2 Capture: <Up>/<Down> - Mirror/Flip (Hard Key)
●
Press <Up> buon to change image leto right
●
Press <Down> buon to upside down image
-14-
<Up> Right/Up
<Down>
Le/Down
<Up>
<Down>
<OK> buon
Go Back to
1.1 Capture

1.3 Capture: <Up>/<Down> - Brightness/Color (Hard Key)
●
Press <Up> buon to enter Brightness adjustment (See Chapter 1.4)
●
Press <Down> buon to enter Color adjustment (See Chapter 1.5)
-15-
<Up> Right/Up
<Down>
Le/Down
<Up>
<Down>
<OK> buon
Go back to
1.1 Capture

1.4 Capture: <Up>/<Down> - Brightness (Hard Key)
●
Press <Up> buon to increase Brightness with ranges of -3 to 3
●
Press <Down> buon to decrease Brightness with ranges of -3 to 3
-16-
<
Up> Right/Up
<Down>
Le/Down
<Up>
<Down>
<OK> buon
Go back to
1.1 Capture

1.5 Capture: <Up>/<Down> - Color Red (Hard Key)
●
Press <Up> buon to increase red color with ranges of -3 to 3
●
Press <Down> buon to decrease red color with ranges of -3 to 3
-17-
<Up> Right/Up
<Down>
L
e
f
t/
D
o
wn
<Up>
<Down>
<OK> buon
Go Next to
Color Green

1.6 Capture: <Up>/<Down> - Color Green (Hard Key)
●
Press <Up> buon to increase green color with ranges of -3 to 3
●
Press <Down> buon to decrease green color with ranges of -3 to 3
-18-
<Up> Right/Up
<Down>
Le/Down
<Up>
<Down>
<OK> buon
Go Next to
Color Blue