Rolls Rm67 User manual

RM67Mic/Source Mixer

Quick Start Guide

ROLLS CORPORATION SALT LAKE CITY, UTAH 03/20

SPECIFICATIONS

Input Impedance: Mic: 600 Ohms XLR balanced

Line: 22K Ohms

Source:

22K

Ohms

gold plated RCA

Mic Insert: 22K Ohms 1/4”TS unbal.

Max Input Level: Mic: -14 dBV Mic level

+20 dB Line levl

Source: 24 dBV

Connectors: 3: XLR, 6: Stereo RCA, 3: 1/4”TRS, 1: 1/4”TS, 1: 3.5mm

Phantom Power: +12 VDC

Output Level: +17 dBV max

Output Impedance: 51 Ohms

Max Gain: Mic: 60 dB

Source: 26 dB

Tone Controls: +/-12 dB 100 Hz Bass

+/-12 dB 11kHz Treble

Nose Floor: - 80 dB, THD: <.025%, S/N Ratio: 96 dB

Size: 19” x 1.75” x 6” (48.3 x 4.5 x 15 cm)

Weight: 5 lbs. (2.3 kg)

NOTE: THIS GUIDE ASSUMES THE USER HAS A WORKING

KNOWLEDGE OF AUDIO ELECTRONICS, BALANCED AND

UNBALANCED CONNECTIONS, AND PROPER SIGNAL LEVEL

SETTING.

Remote Volume Control

To control the overall volume of the RM67 in a remote location, wire a 100K ohm Linear

Taper potentiometer to a 1/4”Tip-Ring-Sleeve plug as shown here.

Mic Insert

To connect a signal processor to the RM67 microphone signal(s), use an insert plug, or

cable wired as shown here.

To Mic Insert

DIP SWITCH SETTINGS

- If a microphone requires phantom power, move the Mic channel’s corresponding

PHAN DIP switch to the down position. This applies 12 volts dc phantom power to the

indicated microphone.

- Talkover switch 1 (T.O. 1), when in the down position, all program material on all

source inputs will be“ducked” or muted when a signal is present at Mic 1. NOTE: MIC

ONE WILL NOT TALK OVER MIC2 OR MIC3. ONLY THE SOURCE INPUTS WILL BE TALKED

OVER. This function is used for paging.

- Talkover switch 2 (T.O. 2), when in the down position, Source 1,2, and 3 will be

“ducked” or muted by the signals at Source 4.

This function is for jukebox priority. With a jukebox connected to Source input 4, and

the Talkover switch 2 on (down), the other Source input signals such as background

music, will be muted and only the jukebox will be heard.

120VAC 50/60Hz

MODEL RM67

www.rolls.com

WARNING: DO NOT EXPOSE

THIS EQUIPMENT TO RAIN OR MOISTURE. RISQUE DE CHOC - NE PAS ENLIVER

MIC DUCK

DEPTH

MADE IN USA

#4 PRIORITY

DUCK SENSITIVITY

TO #1 - MIC

TO #2 - PRIOTIRY #4

- The Mono/Stereo switch selects the

output mode. When the switch is up,

the unit is in stereo mode. When the

switch is down, the stereo signals

are mixed to mono and sent to both

the Right and Left Main output jacks.

Either jack can be used as a mono

output.

Mic 1 - 3: XLR inputs for dynamic or condenser microphones, or balanced line-level signals.

Mic/Line Switch: Pads the XLR Mic input by 30 dB when pressed in.

DIP SWITCH: Contains the small switches for engaging Mic 1 - 3 phantom power, the priority (Talk Over) functions, and the Mono/Stereo select.

MIC INSERT: 1/4”TRS insert jack for adding external processing to the Mic signals. Tip = send, ring = return.

SOURCE INPUTS: Stereo RCA jacks, Channels 1 - 4, for connection to stereo sources such as AM/FM tuners, cassette players, cd players, or video players.

RECORD OUT: Stereo RCA jacks, contains all mixed signals before the Remote Volume jack, and Master Level control.

SPARE: This RCA jack is not connected.

MUTE: RCA jack for connection to a tip-to-ground muting circuit. To mute all audio, connect the tip to ground.

REMOTE VOLUME: 1/4”TS jack for connection to a remote potentiometer for master volume control. 100K Ohm audio taper potentiometer is recommended.

MAIN OUTPUTS: 1/4”TRS balanced Right and Left Outputs.

MIC DUCK DEPTH: Adjusts the level of input signal required for ducking to occur. NOTE: The release time is eected by this setting, plus the level of input sig-

nal - the higher the input signal, the longer the release time.

PRIORITY #4 DUCK SENSITIVITY: Adjusts the level of input signal required for ducking to occur. NOTE: The release time is eected by this setting, plus the level

of input signal - the higher the input signal, the longer the release time.

IEC POWER INPUT: Connect to the IEC power cable - and properly grounded ac outlet.