RoMedic QuickMove User manual

Manual
Article no: 400801334
Manual no: 00793En ver. 2 100510
English
The QuickMove is an active transfer and transport aid, designed for users with poor balance and reduced lower limb
strength. Users will need a degree of arm strength and standing function in order to actively participate in the transfer.
The QuickMove is an ideal aid for users who can raise themselves to an upright, or semi-upright position to be trans-
ferred. The QuickMove can also be used as a turning device to transfer the user from bed to chair or similar.
SystemRoMedic is a series of different models of transfer assistive devices. The choice of assistive devices depends on
the transfer situation and the patient’s functional capability and needs.
Visual inspection
Check the condition and function of the assistive device regularly. Check to ensure that seams and material are free from
damage. If there are signs of wear, the product must be inspected and serviced.
Always read the manuals for all assistive devices used during a transfer.
Keep the manual where it is accessible to users of the product.
Do not leave the patient unattended during a transfer situation.
The product should be inspected yearly, and otherwise as required, by a qualified technician. Service must be performed
by a qualified technician.
Functional inspection
Always read the instructions
QuickMove
Max: 170 kg/375 lbs

MANUAL
Ver.2 100510
1. Seat support
2. Depth adjustable kneepad
3. Reglage för vinkling av säte
4. Manual adjustment of seat
depth
5. Hight adjustable kneepad
6. Footpedal for leg spread
adjustment
7. 2 x rear braked castors
8. Detachable footplate
• Split seat pads: both swing away and flip-up.
(picture 1).
• Knee pad: depth and height adjustable and
tiltable.
• Foot pedal: for adjusting leg spread in and out.
• Angle adjustment crossbar: adjusts seat and
handgrip angle up or down to optimise seating
comfort and positioning of user.
(picture 2).
• Seat depth: two positions, manually adjustable.
• Footplate: covered with non-slip surface,
detachable.
Description of parts
Functions
QuickMove
2
1
2
3
4
5
6
7
87
7
1
2

MANUAL
Ver.2 100510
•QuickMoveisnotintendedforlongtransfers.
•QuickMovecanonlybeusedonflatfloor.
To transfer with QuickMove, the patient must be able to:
•supportweightwhilestanding
•standupandmaintainbalance(withsupport)
•grasphandles
•understandinstructions
Special requirements and conditions
Testing standing function
QuickMove is ideal for testing a patient’s standing function in cases where there is
uncertainty as to whether the patient is able to rise from a seated to a standing posi-
tion.
Training standing function
QuickMove can be used to train the patient’s standing, sitting and sit-to-stand func-
tion. To measure improvement, use a stopwatch or clock with a second hand to time
the patient.
Farther back in the chair
If the patient slides forward in the wheelchair, the QuickMove can be used to help the patient to slide farther back in the
chair.
Remove/raise the wheelchair foot plates, and then run the QuickMove in towards the wheelchair. The patient places his/her
feet on the foot plate, grasps the raising ladder, leans forward, and then lifts from the seat. The caregiver provides counter
pressure. Slide the patient farther back in the chair when he/she has lifted slightly from the seat.
QuickMove
3

MANUAL
Ver.2 100510
Using QuickMove
Place the QuickMove as close to the patient as possible and ask the
patient to place his or her feet on the footrest. Adjust both the height and
depth of the leg supports, as well as the seat depth, if necessary.
The patient can then grasp the soft handlebar and rise to a standing posi-
tion.
When the patient has risen to a standing position, the caregiver lowers the
seat behind the patient.
The patient will then be able to sit during transfer. For optimal sitting com-
fort, the caregiver can regulate the angle of the seat using the adjustment
bar on the handlebar. This function also facilitates standing, since the sitting
height is higher and the patient’s legs are straighter.
QuickMove
4

MANUAL
Ver.2 100510
Technical information
A Length 900-1030 mm 35.4 – 40.5”
B Width, inner. Min. leg spread. Castor to castor. 455 mm 17.9”
C Width, inner. Max. leg spread. Castor to castor. 830 mm 32.6”
D Width, outer. Min. leg spread. Castor to castor. 615 mm 24.2”
E Width, outer. Max. leg spread. Castor to castor. 1050 mm 41.3”
F Width between legs. Min. leg spread. 480 mm 18.8”
G Width between legs. Max. leg spread. 620 mm 24.4”
H Height adjustement: Floor to pushbar 1065 – 1120 mm 41.9 – 44”
I Height: Floor top of castor frame 140 mm 5.5”
J Height: Floor top of leg 45 mm 1.7”
K Seat height: Min. 730 mm 28.7”
L Seat height: Max. 850 mm 33.4”
Seat width: 480 mm 18.8”
Seat depth: 265 mm 10.4”
Castor Ø Ø80 mm Ø3”
Weight: 35 kg 77 lbs
Max. weight capacity: 170 kg 375 lbs
QuickMove
5

Contact your local distributor if you have any questions about the product and its use. See www.romedic.com for a
complete list of distributors. Always make sure that you have the right version of the manual. The most recent editions of
manuals are available for downloading from our website, www.romedic.com.
Care of the product
•UseasoftclothandmildcleaningagentsuchasdishwashingliquidorcarshampootocleantheQuickMove.Donotuse
abrasive cloths or brushes.
•Donotusesolvents.
•Todisinfect,use70%alcohol.
Accessories
SupportStraps
SupportStraps can together with EasyBelt/FlexiBelt/ReadyBelt or
FlexiMove be used as torso/side support to QuickMove.
RoMedic AB
Veddestav. 15, Box 640 Tel: [phone] Internet: www.romedic.com
SE-175 27 Järfälla Fax:[phone] E-mail: [email protected]
SWEDEN
EasyBelt/FlexiBelt FlexiMove