ROSE DISPLAYS ANOGOTCHA ROUND WITH CABLE CLIP AND CABLE AND... User manual

Parts
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Place cable onto inner channel of Cable
Clip. The cable should snap
into place. Fig. 2
Note: For OneUp Application place
the MultiClip in the center of the
AnoGotcha Holder.
Step 3
Align one end of the Cable Clip with the
top channel of the aluminum holder. Then
insert one round end, then press down on
the other round end and slide Cable Clip
into rail. Fig. 3
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close,
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha
Holder, End Caps, Cable Clips and
MultiClips for future projects.
OneUp Instruction Sheet
AnoGotcha™
Instructions for Hanging
Incept-9.27.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaCableClipSaucer
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Figure 2
End Caps
06-5525
Cable Clip
06-5050
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
Cable and
Saucer
16-0018SS

Parts
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Place cable onto inner channel of Cable
Clip. The cable should snap
into place. Fig. 2
Note: For OneUp Application place
the MultiClip in the center of the
AnoGotcha Holder.
Step 3
Align one end of the Cable Clip with the
top channel of the aluminum holder. Then
insert one round end, then press down on
the other round end and slide Cable Clip
into rail. Fig. 3
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close,
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha
Holder, End Caps, Cable Clips and
MultiClips for future projects.
Instructions for Hanging
Incept-9.27.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaCableClipSaucer
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2
OneUp Instruction Sheet
AnoGotcha™
End Caps
06-5525
Cable Clip
06-5050
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
Cable and
Saucer
16-0018SS

Parts
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Place cable onto inner channel of Cable
Clip. The cable should snap
into place. Fig. 2
Step 3
Align one end of the Cable Clip with the
top channel of the aluminum holder. Then
insert one round end, then press down on
the other round end and slide Cable Clip
into rail. Fig. 3
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close,
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha
Holder, End Caps, Cable Clips and
MultiClips for future projects.
Instructions for Hanging
Incept-9.27.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaCableClipSaucer
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2
Instruction Sheet
AnoGotcha™
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
End Caps
06-5525
Cable Clips
06-5050
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
Cable and
Saucer
16-0018SS

Parts
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Place cable onto inner channel of Cable
Clip. The cable should snap
into place. Fig. 2
Step 3
Align one end of the Cable Clip with the
top channel of the aluminum holder. Then
insert one round end, then press down on
the other round end and slide Cable Clip
into rail. Fig. 3
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close,
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha
Holder, End Caps, Cable Clips and
MultiClips for future projects.
Instructions for Hanging
Incept-9.27.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaCableClipSaucer
End Caps
06-5525
Cable Clips
06-5050
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2
Instruction Sheet
AnoGotcha™
Cable and
Saucer
16-0018SS