ROSE DISPLAYS SUPERSNAP WITH ROD, CABLE CLIP AND BALL... User manual

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
SuperSnap™ with Rod Connector
Step 1
Insert single ball of ball chain into
inner channel of Cable Clip. The
cable should snap into place. Fig. 1
Align one round end of cable clip
with top channel of the rail and
insert. Once in place, insert end of
ball chain into channel. Then press
down on the other round end of the
cable clip and slide into rail by
pushing on the clip. Fig. 2
Note: Be sure to push on the cable
clip in order to slide the ball chain
into place. Do not pull on, or push
against, the ball chain as this will
cause it to bind in the channel.
Note: Position CableClip about
halfway down each SuperSnap. Fig. 3
Step 2
Push rod halfway into clip rail
of one SuperSnap. Fig. 4
Step 3
Insert rod into top clip rail of second
SuperSnap until both holders meet.
Fig. 5 & 6 Repeat steps 2-3 for
additional SuperSnaps.
Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCBC
Figure 3
Figure 6
Figure 5
Figure 4
Page 1 of 2
SuperSnap
12S300
Cable Clip
06-5050
End Caps
06-5475
6” Rod
97-0304-06
Figure 1 Figure 2
Ball Chains
96-0302P

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
(continued)
Step 4
Snap all sections of the SuperSnap
open. Fig. 7
Note: It is easier to open and close
the SuperSnap by starting at one
end and working your way down
the holder.
Step 5
Insert poster (top and bottom) into
all sections of SuperSnap. Fig. 8
Step 6
To close, snap the SuperSnap shut.
Fig. 9
Step 7
Push end caps into place. Fig. 10
Step 8
Suspend holders. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCBC
SuperSnap™ with Rod Connector Instruction Sheet
Open all
holders
Finished Look
Page 2 of 2
Figure 10Figure 9
Figure 7 Figure 8
SuperSnap
12S300
Cable Clip
06-5050
End Caps
06-5475
6” Rod
97-0304-06
Ball Chains
96-0302P

Parts
SuperSnap™ with Rod Connector
Step 1
Insert single ball of ball chain into
inner channel of Cable Clip. The
cable should snap into place. Fig. 1
Align one round end of cable clip
with top channel of the rail and
insert. Once in place, insert end of
ball chain into channel. Then press
down on the other round end of the
cable clip and slide into rail by
pushing on the clip. Fig. 2
Note: Be sure to push on the cable
clip in order to slide the ball chain
into place. Do not pull on, or push
against, the ball chain as this will
cause it to bind in the channel.
Note: Position CableClip about
halfway down each SuperSnap. Fig. 3
Step 2
Push rod halfway into clip rail
of one SuperSnap. Fig. 4
Step 3
Insert rod into top clip rail of second
SuperSnap until both holders meet.
Fig. 5 & 6 Repeat steps 2-3 for
additional SuperSnaps.
Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCBC
Figure 3
Figure 6
Figure 5
Figure 4
Page 1 of 2
SuperSnap
12S300
Cable Clip
06-5050
End Caps
06-5475
6” Rod
97-0304-06
Ball Chains
96-0302P
Figure 1 Figure 2

Parts
(continued)
Step 4
Snap all sections of the SuperSnap
open. Fig. 7
Note: It is easier to open and close
the SuperSnap by starting at one
end and working your way down
the holder.
Step 5
Insert poster (top and bottom) into
all sections of SuperSnap. Fig. 8
Step 6
To close, snap the SuperSnap shut.
Fig. 9
Step 7
Push end caps into place. Fig. 10
Step 8
Suspend holders. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCBC
SuperSnap™ with Rod Connector Instruction Sheet
Open all
holders
Finished Look
Page 2 of 2
Figure 10Figure 9
Figure 7 Figure 8
SuperSnap
12S300
Cable Clip
06-5050
End Caps
06-5475
6” Rod
97-0304-06
Ball Chains
96-0302P