ROSE DISPLAYS ANOQUICK ROUND WITH CABLE CLIP AND BALL... User manual

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
Instruction Sheet
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using the
AnoQuick holder, run it across the graphic edge,
crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping it
down firmly to seat the graphic fully. Fig. 2
Step 3
Insert single ball of ball chain into inner channel of
Cable Clip. The cable should snap into place. Fig. 3
Step 4
Align one round end of cable clip with top channel
of the aluminum rail and insert. Once in place,
insert end of ball chain into channel. Then press
down on the other round end of the cable clip and
slide into rail by pushing on the clip. Fig. 4
Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or push
against, the ball chain as this will cause it to bind in
the channel.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6
AnoQuick™
Instructions for Hanging
Incept-7.4.02
Figure 2
The AnoQuick is a trademark of Rose Displays, Ltd.. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickCableClipBallChain
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6
End Caps
06-5525
AnoQuick
12A300
Cable Clips
06-5050
Ball Chains
96-0302P

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
Instructions for Hanging
OneUp
®
Instruction Sheet
AnoQuick™
Incept-7.4.02
The AnoQuick is a trademark of Rose Displays, Ltd.. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickCableClipBallChain
Figure 2
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6
End Caps
06-5525
AnoQuick
12A300
Cable Clip
06-5050
Ball Chain
96-0302P
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using the
AnoQuick holder, run it across the graphic edge,
crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping it
down firmly to seat the graphic fully. Fig. 2
Step 3
Insert single ball of ball chain into inner channel of
Cable Clip. The cable should snap into place. Fig. 3
Step 4
Align one round end of cable clip with top channel
of the aluminum rail and insert. Once in place,
insert end of ball chain into channel. Then press
down on the other round end of the cable clip and
slide into rail by pushing on the clip. Fig. 4
Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or push
against, the ball chain as this will cause it to bind in
the channel.
Note: For OneUp applications, the AnoQuick holder
is conveniently marked in the center.
Slide the Cable Clip to the mark.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6

Parts
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
Instructions for Hanging
Instruction Sheet
AnoQuick
TM
Incept-7.4.02
The AnoQuick is a trademark of Rose Displays, Ltd.. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickCableClipBallChain
Figure 2
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6
End Caps
06-5525
AnoQuick
12A300
Cable Clips
06-5050
Ball Chains
96-0302P
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using the
AnoQuick holder, run it across the graphic edge,
crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping it
down firmly to seat the graphic fully. Fig. 2
Step 3
Insert single ball of ball chain into inner channel of
Cable Clip. The cable should snap into place. Fig. 3
Step 4
Align one round end of cable clip with top channel
of the aluminum rail and insert. Once in place,
insert end of ball chain into channel. Then press
down on the other round end of the cable clip and
slide into rail by pushing on the clip. Fig. 4
Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or push
against, the ball chain as this will cause it to bind in
the channel.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6

Parts
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
Instructions for Hanging
OneUp
®
Instruction Sheet
AnoQuick™
Incept-7.4.02
End Caps
06-5525
AnoQuick
12A300
The AnoQuick is a trademark of Rose Displays, Ltd.. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickCableClipBallChain
Cable Clip
06-5050
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using the
AnoQuick holder, run it across the graphic edge,
crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping it
down firmly to seat the graphic fully. Fig. 2
Step 3
Insert single ball of ball chain into inner channel of
Cable Clip. The cable should snap into place. Fig. 3
Step 4
Align one round end of cable clip with top channel
of the aluminum rail and insert. Once in place,
insert end of ball chain into channel. Then press
down on the other round end of the cable clip and
slide into rail by pushing on the clip. Fig. 4
Note: Be sure to slide the ball chain into place by
pushing on the cable clip. Do not pull on, or push
against, the ball chain as this will cause it to bind in
the channel.
Note: For OneUp applications, the AnoQuick holder
is conveniently marked in the center.
Slide the Cable Clip to the mark.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6
Figure 2
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6
Ball Chain
96-0302P