Rose electronics CrystalView DVI Multi User manual

CrystalView DVI Multi
10707 Stancliff Road Phone: [phone]
Houston, Texas 77099 WWW.ROSE.COM
Quick Installation
Guide

Features


 Supports PC DVI-D and Mac computers


 Extends and splits a single-link DVI-D signal


 Extends up to 220 feet (70m)


 Splits/Extends the input signal into 1, 2, 4, or 8 outputs


 High resolution support up to 1920 x 1080 @ 60 Hz


 All models provide a DVI Video output connector on the transmitter for local
viewing


 Superior video quality over CAT5e or CAT6 cable


 Flash upgradeable


 Automatically reads the DDC information from the locally attached monitor
or uses the internal DDC table if no monitor is attached locally


 DDC table is stored in flash memory


 Compatible with all operating systems


 Perfect image quality at all resolutions


 Ideal for use in:


 Call Centers


 Airport terminals


 Information stations / Kiosks


 Digital signage in retail environments


 Broadcast, from a centralized computer, real time information to remote DVI
monitors up to 220 feet (70m) away


 Rack mountable
Part Numbers
CRK-21DLC DVI-D video extender w/local access (Extends to 1 DVI monitor)
CRK-22DLC DVI-D video extender w/local monitor (Extends to 2 DVI monitors)
CRK-24DLC DVI-D video extender w/local monitor (Extends to 4 DVI monitors)
CRK-28DLC DVI-D video extender w/local monitor (Extends to 8 DVI monitors)
CRV-SRDLC Receiver unit for all models
Resolutions Supported by the internal EDID table
Resolution Refresh Rate
640 x 480 85Hz
800 x 600 85 Hz
1024 x 768 85 Hz
1152 x 870 75 Hz
1280 x 768 75 Hz
1280 x 960 60 Hz
1280 x 1024 60 Hz
1600 x 1200 60 Hz
1920 x 1080 60 Hz

Installation Procedure
This procedure is required as a first step, to allow the CrystalView DVI Multi to
“learn” the EDID characteristics of the Monitor(s) connected to the receiver
unit.
Note: Use DVI-D cables and CAT6 Shielded Cable. Max distance is 220ft (70
meters).
It is recommended that power to all equipment be off
(Computer, monitor(s), transmitter and receiver units)
1. Connect the DVI-D mm cable between the computer’s video port and the
transmitter’s DVI In connector
2. Connect the monitor or projector to the local DVI out connector on the Transmitter
3. Apply power to the monitor or projector
4. Connect the power adapter to a power source and the Transmitter’s +5VDC
power port
(Wait 5 sec. to allow the Transmitter to read and save the monitors DDC table)
5. Disconnect the monitor from the Transmitter and connect it to the Receiver’s
DVI In port
6. Connect a CAT6 STP cable(s) between the Transmitter and Receiver(s)
7. Connect the power adapter to a power source and the Receiver’s +5VDC
power port
8. Apply power to the computer and wait for it to fully boot-up. Adjust the computer’s
resolution, if required. (Max resolution 1920 x 1080)
CRK-21DLC CRK-22DLC CRK-24DLC
Transmitter Transmitter Transmitter
DVI Local DVI Local DVI Local
In DVI In DVI In DVI
OUT OUT OUT
CRV-SRDLC
Receiver (All)

〒103-0014
東京都中央区日本橋蛎殻町 1-16-11
TEL:[phone] FAX:[phone]
URL:http://www.cybernetech.co.jp