Rose electronics QuadraVista User manual

QUADRAVISTA™ QUAD VIDEO KVM SWITCH
10707 Stancliff Road Phone: [phone]
Houston, Texas 77099 WWW.ROSE.CO
Quick Installation Guide

QuadraVista Quick Start Guide
The QuadraVista has been designed to take the guesswork out of the installation
process. The auto-sensing features will determine the type of video monitor
each of the four connected computer has, digital or analog. QuadraVista also will
determine the type of keyboard (USB, PC1, PC2, PC3) and mouse (USB, PS/2,
PS/2 wheel). With these features, you will be up and running in no time.
First, make sure that power is off on QuadraVista and all computers being
connected. Next, connect your KVM user station as shown below. Connect a
USB mouse and USB keyboard to the corresponding USB ports. If a PS/2
keyboard and mouse are used, a PS/2 to USB converter must be used. Next,
connect a VGA or DVI monitor to the DVI-I port. If a VGA monitor is used, a VGA
to DVI converter cable must be used.
Connect up to four computers to the corresponding video (DVI-I),
keyboard/mouse ports on the QuadraVista as shown below.
If a VGA (HD15F) connector is on the computer, a VGA to DVI cable must be
used. If the keyboard and mouse are PS/2, use a PS/2 "Y" cable.
Apply power to the QuadraVista, then computers and user
station monitor. The KVM user stations monitor will display
in the quad mode, all connected computers video.
Refer to the Installation and Operations manual for
additional information about the on-screen menus and other
configurations that can be performed.
KVM user station

QuadraVista Quick Start Guide
Keyboard commands
(Default "HOTKEY" is the CTRL + ALT keys pressed at the same time
followed by the needed command)
Command* Description
"HOTKEY" + Q Change display to quad mode
"HOTKEY" + F Change display to full screen mode
"HOTKEY" + P Change display to PIP function
"HOTKEY" + 1 Switch to computer 1 (Full Screen)
"HOTKEY" + 2 Switch to computer 2 (Full Screen)
"HOTKEY" + 3 Switch to computer 3 (Full Screen)
"HOTKEY" + 4 Switch to computer 4 (Full Screen)
"HOTKEY" + F1 Switch to quad mode and activate channel 1
"HOTKEY" + F2 Switch to quad mode and activate channel 2
"HOTKEY" + F3 Switch to quad mode and activate channel 3
"HOTKEY" + F4 Switch to quad mode and activate channel 4
"HOTKEY" + O Invoke the on-screen menu system
"HOTKEY" + I PIP menu
"HOTKEY" + V Reset video resolution to default setting
(640 x 480 @ 60 Hz)
The QuadraVista has been designed to take the guesswork out of the
installation process. The auto-sensing features will determine the type of
video monitor each of the four connected computer has, digital or analog.
QuadraVista also will determine the type of keyboard (USB, PC1, PC2, PC3)
and mouse (USB, PS/2, PS/2 wheel). With these features, you will be up and
running in no time.
First, make sure that power is off on QuadraVista and all computers being
connected. Next, connect your KVM user station as shown below. Connect
a USB mouse and USB keyboard to the corresponding USB ports. If a PS/2
keyboard and mouse are used, a PS/2 to USB converter must be used.
Next, connect a VGA or DVI monitor to the DVI-I port. If a VGA monitor is
used, a VGA to DVI converter cable must be used.
Connect up to four computers to the corresponding video (DVI-I),
keyboard/mouse ports on the QuadraVista as shown below.
If a VGA (HD15F) connector is on the computer, a VGA to DVI cable must be
used. If the keyboard and mouse are PS/2, use a PS/2 "Y" cable.
KVM user station

QuadraVista Quick Start Guide
Apply power to the QuadraVista, then computers and
user station monitor. The KVM user stations monitor will
display in the quad mode, all connected computers
video.
Refer to the Installation and Operations manual for
additional information about the on-screen menus and
other configurations that can be performed.
Keyboard commands
(Default "HOTKEY" is the CTRL + ALT keys pressed at the same time
followed by the needed command)
Command* Description
"HOTKEY" + Q Change display to quad mode
"HOTKEY" + F Change display to full screen mode
"HOTKEY" + P Change display to PIP function
"HOTKEY" + 1 Switch to computer 1 (Full Screen)
"HOTKEY" + 2 Switch to computer 2 (Full Screen)
"HOTKEY" + 3 Switch to computer 3 (Full Screen)
"HOTKEY" + 4 Switch to computer 4 (Full Screen)
"HOTKEY" + F1 Switch to quad mode and activate channel 1
"HOTKEY" + F2 Switch to quad mode and activate channel 2
"HOTKEY" + F3 Switch to quad mode and activate channel 3
"HOTKEY" + F4 Switch to quad mode and activate channel 4
"HOTKEY" + O Invoke the on-screen menu system
"HOTKEY" + I PIP menu
"HOTKEY" + V Reset video resolution to default setting
(640 x 480 @ 60 Hz)
Copyright 2007 Rose Electronics – All rights reserved
〒103-0014
東京都中央区日本橋蛎殻町 1-16-11
TEL:[phone] FAX:[phone]
URL:http://www.cybernetech.co.jp