Ross MB-652 User manual

MB-652
2RU Monitoring Bridge
User Manual

Thank you for choosing Ross
You've made a great choice. We expect you will be very happy with your purchase of Ross Technology.
Our mission is to:
1. Provide a Superior Customer Experience
• offer the best product quality and support
2. Make Cool Practical Technology
• develop great products that customers love
Ross has become well known for the Ross Video Code of Ethics. It guides our interactions and
empowers our employees. I hope you enjoy reading it below.
If anything at all with your Ross experience does not live up to your expectations be sure to reach out to
us at [email protected].
David Ross
CEO, Ross Video
[email protected]
Ross Video Code of Ethics
Any company is the sum total of the people that make things happen. At Ross, our employees are a
special group. Our employees truly care about doing a great job and delivering a high quality customer
experience every day. This code of ethics hangs on the wall of all Ross Video locations to guide our
behavior:
1. We will always act in our customers’ best interest.
2. We will do our best to understand our customers’ requirements.
3. We will not ship crap.
4. We will be great to work with.
5. We will do something extra for our customers, as an apology, when something big goes wrong and
it's our fault.
6. We will keep our promises.
7. We will treat the competition with respect.
8. We will cooperate with and help other friendly companies.
9. We will go above and beyond in times of crisis. If there's no one to authorize the required action in
times of company or customer crisis - do what you know in your heart is right. (You may rent
helicopters if necessary.)

MB-652 · User Manual
• Ross Part Number: MB652DR-004-04
• Release Date: January 16, 2018.
Copyright
© 2018 Ross Video Limited. Ross®, and any related marks are trademarks or registered trademarks of Ross Video
Ltd. All other trademarks are the property of their respective companies. PATENTS ISSUED and PENDING. All
rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, mechanical, photocopying, recording or otherwise, without the prior written permission of
Ross Video. While every precaution has been taken in the preparation of this document, Ross Video assumes no
responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the
information contained herein.
Patents
Patent numbers US 7,034,886; US 7,508,455; US 7,602,446; US 7,802,802 B2; US 7,834,886; US 7,914,332; US
8,307,284; US 8,407,374 B2; US 8,499,019 B2; US 8,519,949 B2; US 8,743,292 B2; GB 2,419,119 B; GB
2,447,380 B; and other patents pending.
Safety Notices
Refer to the “Important Regulatory and Safety Notices” document that accompanied your product.
EMC Notices
United States of America FCC Part 15
This equipment has been tested and found to comply with the limits for a class A Digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at their own expense.
Canada
This Class “A” digital apparatus complies with Canadian ICES-003.
Cet appariel numerique de la classe “A” est conforme a la norme NMB-003 du Canada.
Europe
This equipment is in compliance with the essential requirements and other relevant provisions of CE Directive
93/68/EEC.
Australia
This equipment has been tested to AS/NZS CISPR 22:2009 and found to comply with the limits for a Class A
Digital device.
Notice — Changes or modifications to this equipment not expressly approved by Ross Video Limited
could void the user’s authority to operate this equipment.

International
This equipment has been tested to CISPR 22:2009 and found to comply with the limits for a Class A Digital device.
Maintenance/User Serviceable Parts
Routine maintenance to this product is not required. This product contains no user serviceable parts. If the module
does not appear to be working properly, please contact Technical Support using the numbers listed under the
“Contact Us” section on the last page of this manual. This product is covered by a generous 1-year warranty and
will be repaired without charge for materials or labor within this period. See the “Warranty and Repair Policy”
section in this manual for details.
Environmental Information
The equipment that you purchased required the extraction and use of natural resources for its production. It
may contain hazardous substances that could impact health and the environment.
To avoid the potential release of those substances into the environment and to diminish the need for the extraction
of natural resources, Ross Video encourages you to use the appropriate take-back systems. These systems will reuse
or recycle most of the materials from your end-of-life equipment in an environmentally friendly and health
conscious manner.
The crossed out wheelie bin symbol invites you to use these systems.
If you need more information on the collection, re-use, and recycling systems, please contact your local or regional
waste administration. You can also contact Ross Video for more information on the environmental performance of
our products.
Company Address
Notice — This is a Class A product. In domestic environments, this product may cause radio
interference, in which case the user may have to take adequate measures.
Ross Video Limited Ross Video Incorporated
8 John Street P.O. Box 880
Iroquois, Ontario, K0E 1K0 Ogdensburg, New York
Canada USA 13669-0880
General Business Office: (+1) 613 • 652 • 4886
Fax: (+1) 613 • 652 • 4425
Technical Support: (+1) 613 • 652 • 4886
After Hours Emergency: (+1) 613 • 349 • 0006
E-mail (Technical Support): techsu[email protected]
E-mail (General Information): solu[email protected]
Website: http://www.rossvideo.com

MB-652 User Manual (Iss. 04) Contents • i
Contents
Introduction 1
Overview.............................................................................................................................. 1-2
Features.................................................................................................................. 1-2
Functional Block Diagrams ................................................................................................. 1-3
User Interfaces ..................................................................................................................... 1-4
DashBoard Control System ................................................................................... 1-4
Controls on the Physical Panel.............................................................................. 1-4
Installation 2
Before You Begin ................................................................................................................ 2-2
Static Discharge..................................................................................................... 2-2
Unpacking.............................................................................................................. 2-2
Front Panel Overview .......................................................................................................... 2-3
Rear Panel Overview ........................................................................................................... 2-4
Physical Installation............................................................................................................. 2-6
Installation Requirements...................................................................................... 2-6
Power Supplies ...................................................................................................... 2-6
To connect the power cables for the MB-652 ....................................................... 2-6
Ethernet Cabling for the MB-652.......................................................................... 2-7
SDI Cabling........................................................................................................... 2-7
Configuring the DIP Switches ............................................................................................. 2-8
Setting the IP Address ........................................................................................... 2-8
Master Password Override .................................................................................... 2-8
SW4 ....................................................................................................................... 2-8
Configuration 3
Using the Front Panel Display ............................................................................................. 3-2
Using DashBoard................................................................................................................. 3-4
To launch DashBoard............................................................................................ 3-4
To access the MB-652 interface............................................................................ 3-4
Using a Master Password in DashBoard.............................................................................. 3-5
Setting the Master Password ................................................................................. 3-5
Setting the DIP Switch .......................................................................................... 3-5
To set a new master password for the MB-652..................................................... 3-5
Accessing a MB-652 ............................................................................................. 3-5
To use a valid user account ................................................................................... 3-6
To use the Master Password.................................................................................. 3-6
Network Configuration ........................................................................................................ 3-7
Before You Begin.................................................................................................. 3-7
Automatic Configuration using DHCP ................................................................. 3-7
To establish communications with the MB-652.................................................... 3-7
Custom User Configuration via DashBoard.......................................................... 3-7
To configure the network settings via DashBoard ................................................ 3-7
Audio Configuration ............................................................................................................3-9
Channel Source Selection...................................................................................... 3-9

ii • Contents MB-652 User Manual (Iss. 04)
Mode Selection ...................................................................................................... 3-9
Adjusting the EQ Levels........................................................................................ 3-9
To adjust an equalizer band ................................................................................... 3-9
Line Out Control.................................................................................................. 3-10
Monitoring the Loudness Value......................................................................................... 3-11
Software Upgrades ............................................................................................................. 3-12
To upload software to the MB-652...................................................................... 3-12
DashBoard Menus 4
Network Connect Interface .................................................................................................. 4-2
Device Tab............................................................................................................. 4-2
Network Tab .......................................................................................................... 4-2
Network Tab .......................................................................................................... 4-3
MB-652 Interfaces ............................................................................................................... 4-4
Status Tab .............................................................................................................. 4-4
Product Tab............................................................................................................ 4-4
LKFS Tab .............................................................................................................. 4-4
Settings Tab ........................................................................................................... 4-5
Equalizer Tab......................................................................................................... 4-6
Default Values ....................................................................................................... 4-6
Specifications 5
Technical Specifications ...................................................................................................... 5-2
Service Information 6
Troubleshooting Checklist ................................................................................................... 6-2
Warranty and Repair Policy ................................................................................................. 6-3
In Case of Problems............................................................................................... 6-3

MB-652 User Manual (Iss. 04) Introduction • 1–1
Introduction
In This Chapter
The following topics are discussed:
• Overview
• Functional Block Diagrams
• User Interfaces
A Word of Thanks
Congratulations on choosing a Ross Video Monitoring Bridge. Thank you for joining the group of
worldwide satisfied Ross Video customers!
Should you have a question pertaining to the installation or operation of your Monitoring Bridge,
please contact us at the numbers listed on the back cover of this manual. Our technical support
staff is always available for consultation, training, or service.

1–2 • Introduction MB-652 User Manual (Iss. 04)
Overview
Each MB-652 is a compact 3G/HD/SD SDI embedded audio monitoring system designed to
extract up to 16 channels of embedded audio from an SDI signal for visual and aural monitoring.
The Monitoring Bridge features an intuitive user interface to allow for easy access to the signals
and information you need to monitor.
A large vacuum fluorescent display on the front panel reports VU/PPM information, LKFS
ITU1770-3/1771 loudness measurements, and true peak measurement. Input signal format data
and mode selection information is also displayed.
Located directly beneath the display are 12 illuminated push-buttons to provide intuitive channel
source and mode selection.
Also located on the front panel is a push to mute rotary shaft encoder for volume control and a
1/4” long-frame jack for headset monitoring.
High quality full range speakers and a Class D amplifier provide unparalleled performance.
One 3G/HD/SD SDI signal can be connected to the BNC on the rear panel while a reclocked
output is available. Two 3-pin terminal block connectors also provide a stereo monitor output.
Features
The following features come standard on the MB-652:
• One 3G/HD/SD SDI input
• One reclocked SDI output
• One stereo monitor output
• Left, Right, SUM, Left Total/Right Total (Lt/Rt) downmix modes
• Push to Mute rotary shaft encoder
• High quality 1/4” long-frame headset jack
• 16 VU/PPM bar graph meters
• Provides ITU 1770-3/1771 LKFS measurements
• Full range speakers
• Class D power amplifier

MB-652 User Manual (Iss. 04) Introduction • 1–3
Functional Block Diagrams
Figure 1.1 outlines the workflow of the MB-652.
Figure 1.1 MB-652 — Simplified Block Diagram
SDI
Video In
SDI
Video Out
16 Channel
DMX
VFD
16 VU/Peak Meters
LKFS Meter
16
CHANNELS
SDI EQ
and
Reclock
DAC
GPIO
Amplifier
Channel Select
Sum/Downmix
Loudness Meter
MON OUT

1–4 • Introduction MB-652 User Manual (Iss. 04)
User Interfaces
The MB-652 is intended to be controlled via the DashBoard client software, as well as through
the physical controls on the panel.
DashBoard Control System
The DashBoard client software enables you to monitor and configure the MB-652 from a
computer. The DashBoard software is available for download from our website.
The MB-652 includes two DashBoard interfaces: Network Connect and MB-652. Both interfaces
are accessed by expanding the MB-652 node in the DashBoard Tree View and selecting the
appropriate sub-node. The Network Connect interface enables you to set up ethernet
communications, and monitor those communications. The MB-652 interface includes operational
controls for the physical panel such as selecting the input source for the speakers and adjusting
the volume level for the speakers.
For More Information on...
• configuring the MB-652 for network communication, refer to the section “Network
Configuration” on page 3-7.
• menus in DashBoard for the MB-652, refer to the chapter “DashBoard Menus” on page
4-1.
• installing and using DashBoard, refer to the DashBoard User Manual.
Controls on the Physical Panel
The front panel of the MB-652 provides the ability to monitor the LKFS and true peak values, the
input signal format, and meters that represent VU/PPM data and loudness measurements. Buttons
are provided to routing audio sources to the speakers, selecting the operating mode, and volume
control.
The rear panel provides connections for the power supply, BNCs for the SDI input and output,
and two 3-pin blocks for monitoring the analog audio.
For More Information on...
• the control and monitoring features of the front panel, refer to the section “Front Panel
Overview” on page 2-3.
• the connections provided on the rear panel, refer to the section “Rear Panel Overview”
on page 2-4.

MB-652 User Manual (Iss. 04) Installation • 2–1
Installation
In This Chapter
This chapter provides instructions for the physical installation of your MB-652, and basic cabling
for the MB-652.
• Before You Begin
• Front Panel Overview
• Rear Panel Overview
• Physical Installation
• Configuring the DIP Switches

2–2 • Installation MB-652 User Manual (Iss. 04)
Before You Begin
Before you begin, ensure to review the following sections.
Static Discharge
Throughout this chapter, please heed the following cautionary note:
Unpacking
Unpack each MB-652 you received from the shipping container and ensure that all items are
included. If any items are missing or damage, contact your sales representative or Ross Video
directly.
ESD Susceptibility — Static discharge can cause serious damage to sensitive
semiconductor devices. Avoid handling circuit boards in high static environments
such as carpeted areas and when synthetic fiber clothing is worn. Always exercise
proper grounding precautions when working on circuit boards and related equipment.

MB-652 User Manual (Iss. 04) Installation • 2–3
Front Panel Overview
This section briefly summarizes the features of the front panel.
Figure 2.1 MB-652 — Front Panel
1. Display Panel
This vacuum fluorescent display panel displays the audio meters and input signal information.
The following information is displayed:
• 16 bar graph VU/PPM meters
• a bar graph meter that reports LKFS ITU 1770-3/1771 loudness measurements
• a numerical readout of the LKFS and true peak measurement
• the input signal format
2. Volume Control
Turn the knob to control the volume. Push the knob to mute the audio.
3. Source Select Buttons
This row of eight push-buttons enable you to route the corresponding source to the speakers of
the MB-652. Refer to the section “Channel Source Selection” on page 3-9 for details.
4. Mode Select Buttons
This row of four push-buttons enable you to quickly specify the operating mode of the MB-652.
Refer to the section “Mode Selection” on page 3-9 for details.
5. Headset Jack
This is a long-frame 1/4” headset jack. When in use, the internal speakers of the MB-652 are
muted.
1) Display Panel 3) Source Select Buttons 5) Headset Jack
2) Volume Control 4) Mode Select Buttons
4
SDI IN MONITOR
1 2 3 4 5 6 7 8 L R SUM Lt/Rt
VOLUME
HEADSET
3
Monitoring Bridge | MB-652
1 2
5

2–4 • Installation MB-652 User Manual (Iss. 04)
Rear Panel Overview
This section briefly summarizes the features of the rear panel.
Figure 2.2 MB-652 — Rear Panel
1. SDI IN BNC
This is the 3G/HD/SD SDI input signal.
2. SDI OUT BNC
This is a reclocked copy of the SDI input signal.
3. MONITOR Ports
These connectors provide analog audio. For a -20dBFS input, there will be a +4dBu output.
4. GPIO Port
Shorting the I pin to the G pin will mute the front speakers, and the audio level on the rear
monitor ports will be controlled by the front volume knob.
5. DIP Switches
SW1 and SW2 are used in conjunction with the DashBoard menus to set the IP Address of the
MB-652. Refer to the section “Configuring the DIP Switches” on page 2-8 for details.
SW3 is used to override the Master Password for the MB-652. This password limits access to the
MB-652.
6. ETHERNET Port
Each MB-652 includes an Ethernet port on the rear panel that is used for communication with
DashBoard and software upgrades via DashBoard.
7. Power Supply Connections
These are the connectors for the primary (PSU1) and optional redundant (PSU2) supplies.
8. Power Cord Bracket Inserts
Install the provided brackets to help retain the power cords to the MB-652 chassis.
1) SDI IN BNC 4) GPIO Port 7) Power Supply Connections
2) SDI OUT BNC 5) DIP Switches 8) Power Cord Bracket Inserts
3) MONITOR Ports 6) ETHERNET Port
Note — If replacement 3-pin plugs are required, contact Ross Technical Support
and order Ross part number 30-01089.
SDI OUTSDI IN MONITOR
2 3 4 7
8
1 65
ETHERNET
GPIO
PSU1 PSU2
MODE

MB-652 User Manual (Iss. 04) Installation • 2–5
For More Information on...
• power supplies for the MB-652, refer to the section “Power Supplies” on page 2-6.
• MB-652 power consumption, refer to the section “Technical Specifications” on
page 5-2.

2–6 • Installation MB-652 User Manual (Iss. 04)
Physical Installation
The MB-652 mounts in the rack frame by means of four rack screws fastened through the front
mounting ears. This should normally be sufficient to carry the load, including the weight of
accompanying cables. Note that the MB-652 installs in a standard 19” rack.
Installation Requirements
Keep the following in mind when installing your MB-652:
• Install the MB-652 for maximum stability during operation and in such a way as to allow
adequate ventilation.
• The MB-652 cannot be sealed in a closed container and must be installed in free air space
where the ambient temperature is monitored and controlled to not exceed 40°C (104°F).
• Ensure that adequate space exists in front and behind the MB-652 and on both sides of
the frame for airflow.
• The location of the MB-652 should be accessible, dry, and dust-free.
Power Supplies
The MB-652 comes standard with one power supply and one A/C power cable. A redundant
power supply is available as an option. The MB-652 power supply is a power factor corrected
supply, capable of working with all world AC standards (100-240V).
This section includes information for connecting the power cables for the MB-652.
To connect the power cables for the MB-652
1. For each power cable, install the provided cable clamp (929-006R) and machine screw
(850-005R) to help retain the power cable connectors to the rear of the MB-652 chassis.
These clamps and screws are included in the shipping container with the Monitoring
Bridge.
2. Connect the DC plug to the power jack located on the rear panel of the MB-652. Refer to
Figure 2.2 for power connection location.
3. Connect the line cord to the power supply.
4. Connect the AC cord to an AC outlet.
Table 2.1 Frame Dimensions
Model Rack Units Height Depth Width
MB-652 2 RU 3.5” (8.89cm) 8.5” (21.59cm) 19” (48.26cm)
Warning Hazardous Voltages — The safe operation of this product’s external
power supply requires that a protective earth connection be provided. This protective
earth is provided by the grounding conductor in the equipment's supply cord. To reduce
the risk of electrical shock to operator and service personnel, this ground conductor must
be connected to an earthed ground.
Warning — In some countries, it may be necessary to supply the correct mains supply
cord. Use only an approved IEC 320 C-13 type A/C line cord rated for a minimum 10A at
250V and certified for the country of use.

MB-652 User Manual (Iss. 04) Installation • 2–7
Ethernet Cabling for the MB-652
The exact steps for connecting to your facility via an ethernet network depends on the network
requirements of your facility.
Contact your IT Department before connecting to your facility network to ensure that there are no
conflicts. They will provide you with an appropriate value for the IP Address, Subnet Mask, and
Gateway for the MB-652.
You will require a standard network CAT-5 cable to connect the MB-652 to your facility network.
Ross Video does not supply this cable.
SDI Cabling
The rear panel includes one SDI IN BNC and one SDI OUT BNC.

2–8 • Installation MB-652 User Manual (Iss. 04)
Configuring the DIP Switches
This section briefly summarizes the DIP Switch settings on the MB-652. Figure 2.3 shows the
DIP Switches in the UP position.
Figure 2.3 DIP Switches — Set to the UP Positions
Setting the IP Address
SW1 and SW2 are used in conjunction with the DashBoard menus to set the IP Address of the
MB-652. Refer to Table 2. 2 for DIP Switch positions. For information on configuring the
network settings for your MB-652, refer to the section “Network Configuration” on page 3-7.
Master Password Override
SW3 is used to override the Master Password and allows a user to reset the Master Password.
Refer to the section “Using a Master Password in DashBoard” on page 3-5 for details.
•UP — This is the recommended position. A user-specified Master Password is used. The
default password is password. It can be changed using DashBoard as outlined in the the
section “Setting the Master Password” on page 3-5.
•DOWN — This position is used to recover a lost Master Password. The user-specified
password is temporarily ignored, and the default value of password is used.
SW4
SW4 is not implemented at this time and should be left in the UP position.
Table 2.2 SW1 and SW2 Positions
SW1
Position
SW2
Position
Controlled via
DashBoard Descriptions
UP UP The MB-652 network settings can be set by the user
from the DashBoard Network taba. (default)
a. DHCP Mode is assumed until the user changes the settings in DashBoard.
UP DOWN The MB-652 network settings are automatically
assigned (DHCP Mode).
DOWN UP The MB-652 IP Address is set to 192.168.2.1 and
the Subnet Mask is set to 255.255.255.0.
DOWN DOWN The MB-652 IP Address is set to 10.1.2.1. and the
Subnet Mask is set to 255.255.255.0.
1342

MB-652 User Manual (Iss. 04) Configuration • 3–1
Configuration
In This Chapter
This chapter provides instructions to configure basic communications for your MB-652.
The following topics are discussed:
• Using the Front Panel Display
• Using DashBoard
• Using a Master Password in DashBoard
• Network Configuration
• Audio Configuration
• Monitoring the Loudness Value
• Software Upgrades

3–2 • Configuration MB-652 User Manual (Iss. 04)
Using the Front Panel Display
This section provides a brief summary of the display panel located on the front of the MB-652.
From this panel you can monitor the MB-652.
Figure 3.1 MB-652 Front Panel — Display
1. Audio Channel Bar Graph
This sixteen channel bar graph represents the VU/PPM meter where reference can be -20dBFS
(the default value) or -18dBFS. This value can be set in DashBoard via the Settings tab as
outlined in Tabl e 4.7 on page 4-5.
2. FAST Bar Graph
This ITU 1770-3 LKFS bar graph reports the FAST 1 second integration time.
3. Long Term Readout Time
This value is configurable via the options on the LKFS tab in DashBoard.
• ITU 1770 LKFS non gated moving variable. (1 to 30 seconds)
• ITU 1770-2 LKFS gated moving loudness (LT). (30 seconds)
• ITU 1770-2 LKFS gated window (LT). (1-1200 seconds)
4. True Peak Readout
This value is the ITU 1770-3 LKFS numerical read-out of the true peak (PK).
5. Signal Data Display
This area includes the following fields:
•SIG field — Displays the type of SDI signal.
•GRP field — Indicates which groups of audio are present.
•RST field — Represents the timer and is configured via the Front Panel Display options
on the LKFS tab in DashBoard as follows:
› This field is reset each time you select a different source.
›If the Front Panel Display is set to Var Win, it will display the window set time.
›If the Front Panel Display is set to Gated Win, a fixed 30sec window will be
indicated.
›If the Front Panel Display is set to Integrated, it will count to the Gate Time value
(on the LKFS tab in DashBoard), and stop.
1) Audio Channel Bar Graph 3) Long Term Readout Time 5) Signal Data Display
2) FAST Bar Graph 4) True Peak Readout 6) Speaker Volume
SDI IN MONITOR
1 2 3 4 5 6 7 8 L R SUM Lt/Rt
VOLUME
HEADSET
1 FAST INT LKFs PEAK—— —2345678dB
SIG:
GRP:
RST:
720P
1234
13:41
-20 -06
4
4
3
1 5 6
2