Roswell Chaparral Triton Board Rack Setup guide

www.roswellmarine.co m
Installation & Usage Instructions
Part # C927-1801
Chaparral
Triton Board Rack
REV 02-Nov-17
If you have any questions please call : 1-321-638-1331
Information: [e-mail]

Chaparral Triton Installation Instructions w w w. r o swe llmarine.c o m
2
PAC K AG E C ONTEN T S TOOLS NEEDED
THREADLOCKER
RED
BLUE
3/16” Allen Key
5/32” Allen Key
5/16” Allen Key
(x2) Chaparral
Triton Rack
(x2)
Mag Swivel
(x2)
Rack Spacer
(x2) Set of Tower
Adapters x8 x4x8x4x8x4x4
x8
x4
Torque
wrench
Phillips
Screwdriver
3/16”
5/32”
THREADLOCKER
Torque bolts
to 15ft-lb
5/16” BLUE
THREADLOCKER
THREADLOCKER
Torque bolts
to 25ft-lb
Roswell strongly recommends that a routine inspection of hardware and components be done to ensure
proper function and safety and to maximize product life. If bolts are found to be loose, discontinue use
until Loctite is re-applied and bolts are re-tightened.
BApply red thread lock to the swivel alignment pins and thread them into the
board rack spacer. Next, apply red thread lock to the countersunk 1/4-20 x 2.25”
screws and attach the swivel and spacer to the board rack. Torque to 15 ft. lbs.
ATTENTION
1/4-20 x 2.25” 3/8-16 x 4.00” 1/4-20 x 2.25”
Swivel Alignment Pin
6-32 x 0.50”
3/8-16 Lock Nut
3/8” washer
x4
x4
x4
x8
AFirst, bolt the adapter blocks to the port and starboard tower tubes.
Torque the locknuts to 25ft-lbs. Second, apply blue threadlock to
the four 6-32 x 0.50”and install the aluminum cover plate.
Note orientation
of swivel: Handle to top.

C
3/16”
THREADLOCKER
Mount one rack to each swivel block on either side of your tower using
the hardware provided. The racks are not side specic. Apply red
thread lock to all 8 bolts rst.
x8 Torque bolts
to 15ft-lb
Chaparral Triton Usage Instructions w w w. r o s w e llmarine.c o m
3
DYour Triton rack is designed to be adjustable to
t just about any size of wakeboard, wakesurfer
or wakeskate. There are 2 settings, one for
narrower boards, one for wider boards.
EAdjust your telescopic arms one at a time. To adjust your telescopic
arms loosen the knobs on both sides of the rack for the same arm
until the knobs are past the counterbored holes they sit in. At this
point you will be able to slide the whole arm assembly up or down
to the next position where you will then retighten the knobs.
Knob to loosen/tighten Tighten
Make sure your adjustment
knobs are tight periodically.
Narrow board setting
Wide board setting
In the narrow setting, the
max board width should
be no greater than 20”
inches and no less than 14”
inches.
In the wide setting, the
max board width should
be no greater than 23”
inches and no less than
17” inches.

Chaparral Triton Usage Instructions w w w. r o s w e llmarine.c o m
4
Inserting Boards
1 : Slide your board
into one of the
Triton rack slots.
2 : Pull up on the telescopic
arm and ip your board
towards it.
3 : Let the telescopic arm
clamp down over your
board. To remove a
board, repeat steps 1-3 in
reverse
Locate wakeboards with sharp edges
within the harder rubber wakeboard
pads in the tine slots. This is essential to
avoid damaging the softer foam, which
is intended for fragile surfboards and
wakesurfers.
Rubber
wakeboard
pads
Rubber
wakeboard
pads
Use & Care
It is necessary to regularly check the tightness of the bolts on your clamp. Bolts and screws tend to rattle loose over time due to the
vibrations and shaking that your boat experiences while on the water or in transit.
Do not clean your this product with harsh cleaners. Your rack and clamp is built from billet aluminum with a clear anodized coating
to protect it from corrosion. Harsh cleaners like brake cleaner or acetone can damage this anodizing and this product will start to
corrode. A damp rag with a mild soap is ideal for cleaning your rack and clamp.