Roth QuickStop Pro1 User manual

Roth QuickStop Pro1
Installation manual

Installation manual UK..........................................................3
Installationsvejledning DK....................................................7
Installationsmanual SE ....................................................... 11
Installasjonshåndbok NO....................................................15
Asennusohjeet FI.................................................................19
Roth QuickStop Pro1
2/24 - Installation manual

UK Installation - 3/24
1. Control unit
2. Solenoid valve
3. Pressure sensor
4. Power adapter
5. Flow sensor
6. Installation manual
7. QuickGuide
1
2
3
5
4
Roth QuickStop Pro1
Installation manual
1: The TEST indicator light ashes if the system is running
a tightness test and keeps the light on while the device
is monitoring ow.
2: Current operating mode lights up
continuously = HOME
ashes quickly = AWAY
ashes slowly = PAUSE
3: Press MODE for toggling between HOME/AWAY mode.
Keep the button pressed to go to PAUSE mode, in order
to consume water for a longer time period without
getting an alarm.
4: While the VALVE indicator is on, the valve is closed,
and water cannot ow through it.
5: The NETWORK indicator turns o when the device is
oine; ashes when the device is in pairing mode;
and stays on when the device is online and connected
to the Roth Cloud service.
6: Flashes on WARNING before the water is shut o.
Lights up continuously on ALARM and the water is
shut o.
7: Press CLEAR briey to silence the alarm sound.
Keep it pressed to clear the alarm.
Roth QuickStop Pro1 QuickGuide
WHAT DO I DO WHEN...?
We are home - set operating mode to HOME
We are traveling - set operating mode to AWAY
We are using a lot of water - set operating mode to
PAUSE
WHAT SHOULD I DO ABOUT ...?
WARNING - clear the warning and and then check the
cause.
ALARM - First check the cause. Ensure there is no
visible leakage. Take action if needed. Turn the water
back on by clearing the alarm.
Find the leak detection guide on
www.Roth.Support/QuickStop_Pro_UK
In case of repeated alarms the cause must be carefully
investigated.
UK
Roth QuickStop Pro1 QuickGuide_20210525
QuickStop Pro 1
1
2
5
3
6
4
7
6
7
UK

4/24 - UK Installation
Notice!
Installation manual for installers
Installation of Roth QuickStop Pro1 must be performed by a professional installer.
Installation must be in accordance with national and local codes and requirements.
The valve unit must be installed in a frost free environment.
Inlet water pressure should not exceed 10 bar and the unit will function with water
temperatures between 0 – 90°C.
The solenoid valve and sensor unit are paired to a unit and pressure tested before delivery.
The manufacturer’s warranty will be void if this assembly is modied.
Important! Safety equipment using water (e.g. re sprinklers), must be ensured its supply of water
and must be supplied from before the QuickStop Pro1 and thus cannot not be connected to the pipe
network protected by QuickStop Pro1.
Warranty
The unit must be installed in accordance with these instructions, in order for the product
warranty to be eective. The functioning of the product depends on its correct installation.
No parts, such as dirt lter included in the set, may be le out or substituted, e.g. with parts
priorly installed.
Roth QuickStop Pro1 without Wi-Fi access
Roth QuickStop Pro1 can be installed without Wi-Fi access. The tap water installation will still
be protected by Roth QuickStop Pro1, even though app and cloud functions are not in use and
notications not available.
To have full utilization of your system we strongly recommend connecting to the app and cloud.
Roth QuickStop Pro1 with Wi-Fi access
Ensure you have access to a good Wi-Fi signal from the position, where the display unit will be
mounted. One way of doing could be trying to connect a smart phone or tablet to the Internet
via the Wi-Fi at that precise location. Succeeding with that will likely ensure the connecting of
QuickStop Pro1 to Roth app and cloud service.
NOTE! It is not enough just to check the Wi-Fi signal strength on the mobile device since this only
applies to signal reception. In order to ensure the wireless connection is functioning, the best way
is to check the transmission by actually using the Wi-Fi network.

UK Installation - 5/24
Installation of product
1. Close the stop valve of the water inlet.
2. Then ush the pipes carefully by gently opening the stop valve, until no particles can be seen
in the ushing water, before installing the QuickStop Pro1.
3. Any accessories supplied with the product package are manufactured of brass approved for
pressurized tap water.
In order to avoid corrosion caused by galvanic current, never use any parts or materials,
which are galvanized, zinc-plated or made of black steel for mounting purposes.
4. The QuickStop Pro1 unit should be installed aer the water meter, and as early as possible in
the pipe system. The arrow on the solenoid valve shows the direction of the ow of water.
Be extremely careful when cutting any pipes for mounting purposes, and make sure that no
thread seal tape or ax bers are le inside the pipes, which could be carried by water into
the valve unit and prevent the Leakomatic sensor from working.
5. The QuickStop Pro1 can be mounted freely on either a horizontal or a vertical pipe.
6. However in order to prevent particles from getting into the coil sha, if possible, mount the
valve unit so the coil is facing upwards.
7. The valve unit should be mounted so that it is not aected by any lateral or longitudinal
compression, torsion, or traction forces.
8. Gently reopen the stop valve at the water inlet.
9. Visually inspect the installation to ensure water tightness of the assembly work.
We recommend installing a ball valve right aer the QuickStop-unit for easier maintenance
operations.
It is also recommendable to mount a check valve on the cold water supply pipe.
Be aware of national ruler regarding use of check valves in tap water installation.
Front
Right
Left
QuickStop Pro 1

6/24 - UK Installation
Mounting of wiring harnesses
Mounting of the control unit and its connection to the pressure sensor is normally carried out
before the delivery.
Always disconnect power from the control unit before dismantling from the valve unit to prevent
power surges that could damage the electronic components.
1. Check that the pressure sensor’s plug is connected to the sensor and the other end is
connected to the “Sensor” connector on the control unit.
2. The power adaptor is connected to the socket and the connector “Power” of the control unit.
Aer installation
Check that ...
> The unit does not register any ow when water supply is turned o.
> The test indicator’s blue light is on when water is running continuously.
> The blue LED goes o shortly aer the tap is closed.
> To carry out the functionality test
1. By setting the system into “Away” mode.
2. By opening a tap and let the water run until the ow is registered.
Shortly aer the valve unit will shut o the water and the red alarm LED lights up.
If the alarm audio is activated, you will also hear the alarm sound.
> Warnings and alarms can be reset with the “Reset” button. One short press turns o the
alarm sound, while holding down the button will reset the respective alarm.
The troubleshooting and leak detection guide are available on our website at
www.Roth.Support/QuickStop_Pro_UK
Maintenance
The dirt lter should minimum be cleaned once a year. Pour some clean water in a bucket or the
like, then shut the stop valve and remove the dirt lter’s strainer, clean it by using a small brush
like e.g. a toothbrush and rinse it in the clean water.
Reassemble the parts and gently turn the water back on.
Aer any maintenance always check that the valve unit shuts o the ow of water correctly by
carrying out a functionality test.
AUX outAUX in Sensor Flow Power

DK Installation - 7/24
1. Roth QuickStop styring
2. Magnetventil
3. Tryksensor
4. Strømadapter
5. Flowsensor
6. Installationsvejledning
7. QuickGuide
1
2
3
4
DK
Roth QuickStop Pro1
Installation manual
1: The TEST indicator light ashes if the system is running
a tightness test and keeps the light on while the device
is monitoring ow.
2: Current operating mode lights up
continuously = HOME
ashes quickly = AWAY
ashes slowly = PAUSE
3: Press MODE for toggling between HOME/AWAY mode.
Keep the button pressed to go to PAUSE mode, in order
to consume water for a longer time period without
getting an alarm.
4: While the VALVE indicator is on, the valve is closed,
and water cannot ow through it.
5: The NETWORK indicator turns o when the device is
oine; ashes when the device is in pairing mode;
and stays on when the device is online and connected
to the Roth Cloud service.
6: Flashes on WARNING before the water is shut o.
Lights up continuously on ALARM and the water is
shut o.
7: Press CLEAR briey to silence the alarm sound.
Keep it pressed to clear the alarm.
Roth QuickStop Pro1 QuickGuide
WHAT DO I DO WHEN...?
We are home - set operating mode to HOME
We are traveling - set operating mode to AWAY
We are using a lot of water - set operating mode to
PAUSE
WHAT SHOULD I DO ABOUT ...?
WARNING - clear the warning and and then check the
cause.
ALARM - First check the cause. Ensure there is no
visible leakage. Take action if needed. Turn the water
back on by clearing the alarm.
Find the leak detection guide on
www.Roth.Support/QuickStop_Pro_UK
In case of repeated alarms the cause must be carefully
investigated.
UK
Roth QuickStop Pro1 QuickGuide_20210525
QuickStop Pro 1
1
2
5
3
6
4
7
6
7
5

8/24 - DK Installation
Bemærk!
Installationsvejledning for installatører
Installation af Roth QuickStop Pro1 skal udføres af en faglært installatør.
Installationen skal være i overensstemmelse med nationale og lokale retningslinjer og krav.
Roth QuickStop skal installeres i frostfrie omgivelser.
Vandforsyningen må ikke overstige 10 bar, og enheden fungerer med vandtemperaturer
mellem 1 – 90°C.
Magnetventilen og sensorenheden er parret til en enhed og tryktestet før levering.
Producentens garanti bortfalder, hvis denne enhed ændres..
Vigtigt! Vandtilførslen til sikkerhedsudstyr, der forbruger vand (f.eks. brandsprinklere), skal sikres,
og det skal tilsluttes vandtilførelsen før Roth QuickStop Pro1 og kan derfor ikke tilsluttes det rørnet,
der er beskyttet af QuickStop Pro1.
Garanti
Enheden skal installeres i overensstemmelse med denne vejledning, for at produktgarantien
er gældende. Produktets funktion aænger af korrekt installation. Ingen dele som er inkluderet i
sættet, må udelades eller erstattes af tidligere installerede dele, som f.eks. snavslteret.
Roth QuickStop Pro1 uden Wi-Fi-adgang
Roth QuickStop Pro1 kan installeres uden Wi-Fi-adgang. Brugsvandsinstallationen vil stadig
være beskyttet af Roth QuickStop Pro1, selvom app- og cloudfunktionerne ikke er i brug.
Meddelelser vil dog i denne situation ikke være tilgængelige. For at udnytte systemet fuldt ud
anbefaler vi på det kraigste, at du opretter forbindelse til appen og clouden.
Roth QuickStop Pro1 med Wi-Fi-adgang
Sørg for, at du har adgang til et godt Wi-Fi-signal fra den position, hvor Roth QuickStop Pro
styringen monteres. Dette kan gøres ved at forsøge at forbinde en smartphone eller tablet til
internettet via Wi-Fi på det præcise sted. Lykkes det, vil tilslutningen af Roth QuickStop Pro1 til
Roth appen og cloudtjenesten sandsynligvis også fungere.
BEMÆRK! Det er ikke nok blot at kontrollere Wi-Fi-signalstyrken på mobilenheden, da dette kun
vedrører signalmodtagelse. For at sikre, at den trådløse forbindelse fungerer, er den bedste måde at
kontrollere transmissionen på rent faktisk at bruge Wi-Fi-netværket.

DK Installation - 9/24
Installation af produkt
1. Luk stopventilen på vandtilførelsen.
2. Skyl dereer rørene forsigtigt ved langsomt at åbne for stopventilen, indtil der ikke kan ses
partikler i skyllevandet, før du installerer Roth QuickStop Pro1.
3. Alt tilbehør, der følger med produktpakken, er fremstillet af messing, der er godkendt til
tryksat brugsvand.
For at undgå korrosion forårsaget af galvanisk strøm må der aldrig anvendes dele eller
materialer, som er galvaniseret, zinkbelagt eller fremstillet af sort stål til monteringsformål.
4. Roth QuickStop Pro1 enheden skal installeres eer vandmåleren og så tidligt som muligt i
rørsystemet. Pilen på magnetventilen viser vandets owretning.
Vær yderst forsigtig, når du skærer rør til monteringsformål, og sørg for, at der ikke eerlades
gevindtape eller hørbre inde i rørene, som kan føres med vandet ind i ventilenheden og
forhindre QuickStop-sensoren i at fungere.
5. Roth QuickStop Pro1 kan monteres frit på enten et vandret eller et lodret rør.
6. Men for at forhindre partikler i at komme ind i spoleakslen, bør man hvis det er muligt,
montere ventilenheden, så spolen vender opad.
7. Ventilenheden skal monteres, så den ikke påvirkes af side- eller langsgående
kompression, vridning eller trækkræer.
8. Genåbn forsigtigt stopventilen ved vandtilførelsen.
9. Eerse installationen visuelt for at sikre, at installationen ikke er utæt.
Vi anbefaler, at der installeres en kugleventil lige eer Roth QuickStop Pro enheden for at
lette vedligeholdelsen. .
Det anbefales desuden at montere en kontraventil på koldtvandsrøret.
Vær opmærksom på nationale regler vedrørende brug af kontraventiler i brugsvandsinstallationer.
Front
Right
Left
QuickStop Pro 1

10/24 - DK Installation
Montering af ledningsnet
Montering af styreenheden og dens forbindelse til tryksensoren udføres normalt før levering.
Aryd altid strømmen fra styringen før afmontering fra ventilenheden for at forhindre strøm-
stød, der kan beskadige de elektroniske komponenter.
1. Kontroller, at tryksensorens stik er tilsluttet sensoren, og at den anden ende er
tilsluttet ”Sensor”-stikket på styreenheden.
2. Strømadapteren tilsluttes stikudtaget og styreenhedens ”Power”-stik.
Eer installation
Kontroller, at ...
> Enheden ikke registrerer et ow, når vandtilførslen er slukket.
> Testindikatorens blå lys er tændt, når vandet løber konstant fra en hane.
> Den blå LED slukker kort tid eer, at hanen er lukket.
> Funktionstesten udføres
1. Ved at indstille systemet til “Ude”-tilstand.
2. Ved at åbne en hane og lade vandet løbe, indtil der registreres et ow.
Kort tid eer lukker ventilenheden for vandet, og den røde LED-alarm lyser.
Hvis alarmfunktionen er aktiveret, vil du også høre alarmlyden.
> Advarsler og alarmer kan nulstilles med knappen “Reset” (Nulstil). Et kort tryk slår
alarmlyden fra, og den pågældende alarm nulstilles, når du holder knappen nede.
Vejledninger til fejlnding og registrering af utætheder er tilgængelige på vores websted på
www.Roth.Support/QuickStop_Pro_DK
Vedligeholdelse
Snavslteret skal mindst rengøres én gang om året. Hæld noget rent vand i en spand eller
lignende, luk dereer stopventilen og tag snavslterets gitter ud, rengør det med en lille
børste som fx en tandbørste og skyl den med rent vand.
Saml delene, og tænd forsigtigt for vandet igen.
Eer vedligeholdelse skal du altid kontrollere, at ventilenheden slukker vandowet korrekt
ved at udføre en funktionstest.
AUX outAUX in Sensor Flow Power