rough country 70213 User manual

Thank you for choosing Rough Country for all your lighting needs.
Please read instructions before beginning installation. Check the kit hardware against the kit contents
shown below. Be sure you have all needed parts and know where they go.
If question exist, please call us @1-800-222-7023. We will be happy to answer any questions concerning the design,
function, and correct use of our products.
Only fits 2017-18 Super Duty models.
FORD 2017-18 Super Duty Mesh Grille
921702130
Tools Needed:
7mm Socket
10mm Socket/Wrench
Flat Screwdriver
7/16” Socket
7/16” Wrench
5/32” Allen Wrench
1/8” Allen Wrench
Ratchet
Tape
70216 Kit Contents
(1) Grille Trim Ring
(1) Mesh Grille
(2) Light Mounting Brackets
(1) Instructions
(1) Top Mounting Plate
(1) Bottom Mounting Plate
(2) 12” Cree LED Lights
(1) Horn Relocation Bracket
(1) Driver Mounting Bracket
(1) Passenger Mounting Bracket
(1) 70214BAG
(18) 1/4” x 5/8” Button Head Allen Bolts
(40) 1/4” x 1/2” Button Head Allen Bolts
(58) 1/4” Lock Nuts
(5) Upper Brackets
(5) Lower Brackets
70213 Kit Contents
(1) Grille Trim Ring
(1) Mesh Grille
(1) Instructions
(1) Top Mounting Plate
(1) Bottom Mounting Plate
(1) Driver Mounting Bracket
(1) Passenger Mounting Bracket
(3) Lower Center Mounting Brackets
(1) 70213BAG
(12) 1/4” x 5/8” Button Head Allen Bolts
(46) 1/4” x 1/2” Button Head Allen Bolts
(58) 1/4” Lock Nuts
(5) Upper Brackets
(5) Lower Brackets
70213
70216

When tightening button head bolts, only turn the nut!
1. Park the vehicle on a smooth level surface.
2. Remove the 11 push pins using a flat screwdriver or removal tool. Save for reuse. Remove the radiator cover and
set aside. See Photo 1.
3. Using a 10mm socket, remove the upper grille bolts, retain for reuse. See Photo 2.
4. Using a large flat screwdriver, push down on the 4 lower grille clips and remove the grille. See Photo 3.
5. Lay the supplied grille trim ring and grille face down. Use the supplied 1/4” x 1/2” bolts and nuts to attach the trim
ring to the grille. Tighten using a 5/32” Allen and a 7/16” wrench. Do not use holes shown in Photos 4 & 6.
6. Attach the 5 supplied upper brackets to the grille using the supplied 1/4” x 5/8” bolts and nuts. Do not tighten at this
time. See Photo 4. See page 5 for bracket identification.
7. Attach the upper mounting plate to the brackets using the supplied 1/4” x 1/2” bolts and nuts. Tighten using a 5/32”
Allen and a 7/16” wrench. See Photo 5.
8. Attach the 5 supplied lower brackets to the grille using the supplied 1/4” x 5/8” bolts and nuts. Do not tighten at this
time. See Photo 6. See page 5 for bracket identification.
Photo 1 Photo 2
Photo 3 Photo 4
Photo 6Photo 5
Remove radiator cover push pins. Remove upper grille bolts
Unclip the lower grille clips. Attach trim ring to mesh grille.
Tighten upper mounting plate. Attach lower mounting plate brackets.
Notice Tab position.

9. Attach the lower plate to the brackets using the supplied 1/4” x 1/2” bolts and nuts. Tighten using a 5/32” Allen and
a 7/16” wrench. See Photo 7.
10. Attach the driver and passenger brackets to each side of the grille using the supplied 1/4” x 5/8” bolts and nuts.
Tighten using a 5/32” Allen and 7/16” wrench. See Photos 8 & 9.
11. If you are installing the grille without lights, skip to step 20.
12. Attach the supplied light brackets to the grille using the supplied 1/4” x 5/8” bolts and nuts. Tighten using a 5/32”
Allen and 7/16” wrench. See Photo 10.
13. Attach the lights to the brackets using the supplied hardware. Tighten using the supplied Allen. See Photo 11.
14. Wire the lights according to the directions included with the lights.
15. Unplug the horns. See Photo 12.
Photo 8
Photo 10
Photo 7
Photo 9
Photo 11 Photo 12
Tighten lower mounting plate. Attach dr and pass side brackets.
Attach dr and pass side brackets. Attach light mounting brackets.
Unplug horn.Install lights.

16. Using a 10mm socket, remove the horns and bracket from the truck. See Photo 13.
17. Using a 10mm socket, remove the horns from the factory bracket. Retain hardware for reuse. See Photo 14.
17. Install the horns on the supplied horn bracket using the factory hardware. Tighten using a 10mm socket. See Pho-
to 15.
18. Install the horn assembly on the grille using the hardware that was previously installed. Tighten using a 5/32” Allen
and a 7/16” wrench. See Photos 16 & 17.
19. Using a flat screwdriver, remove the 4 clips from the bottom of the factory grille. See Photo 18.
Photo 17
Photo 13 Photo 14
Remove horn assembly.
Photo 18
Photo 15 Photo 16
Install horns on supplied bracket. Attach horn bracket to grille.
Remove horns from bracket.
Remove lower grille clips.

21. Install the 4 factory clips on the lower mounting plate. See Photos 19 & 20.
22. Using a T25, remove the side mounting hardware from the truck. Retain for reuse. See Photo 21.
23. Install the grille assembly by gently pushing in on the bot-
tom until all clips are secured.
24. Plug in the lights and horn if installing the light combo
grille.
25. Using a T25 and the factory hardware, attach the side
mounting brackets to the truck.
26. Using the factory bolts, bolt the top mounting plate to the
truck and tighten using a 10mm socket.
27. Install the radiator cover using the factory push pins.
Photo 19 Photo 20
Install clips on lower mounting plate.
Photo 21
Remove side mounting bolts.
This side against the grille.
Lower Plate Mounting Bracket
Upper Plate Mounting Bracket
This side against the grille.

By purchasing any item sold by Rough Country, LLC, the buyer expressly warrants that he/she is in compliance with all
applicable , State, and Local laws and regulations regarding the purchase, ownership, and use of the item. It shall be
the buyers responsibility to comply with all Federal, State and Local laws governing the sales of any items listed, illustrat-
ed or sold. The buyer expressly agrees to indemnify and hold harmless Rough Country, LLC for all
claims resulting directly or indirectly from the purchase, ownership, or use of the items.